Manual Fixtures
Connect a UUT's test nodes to test connections by hand.
See Also: Mechanical Fixtures
-
Product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
-
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
Product
Automatic Fixture Removal
S95007B
-
Many devices do not have coaxial connectors and so they are put in fixtures in order to measure them in a coaxial environment. You must accurately remove the effects of the fixture to get a good measurement of the device under test (DUT). This option adds a powerful application wizard to guide you through characterizing a fixture and removing it from the measurement. The S95007B software is compatible with M980xA PXI Vector Network Analyzers.
-
Product
Grips and Fixtures for Force Gauges
-
AMETEK Sensors, Test & Calibration
We supply a range of grips and fixtures for the Chatillon force gauges. Below you will find a selection of our most popular grips and fixtures. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
Product
Fixture Design
-
TestEdge offers quick, cost effective test fixture design services for low-speed, full-speed, and high-speed devices. Based on our experience in developing high performance test fixtures for a wide variety of devices, test sockets, and tester platforms, we provide a premium quality test and engineering validation environment for everything from high power (40W) to high pin count to high speed ECL to high speed SerDes (3.25Gb) devices.
-
Product
Test Fixture and Test Programing
-
Landrex Technologies Co., Ltd.
Test Fixture and Test Programing
-
Product
Mechanical Test Fixtures
MMI series man-machine interface
-
Designed to meet the needs of the most discerning customers and the latest market demands, our MMI series guarantees a natural posture for both the operator and the sitting position when performing the test on the adapter. The newly developed lever mechanism, which has been registered as a utility model, is specially adapted to the hand movement of its employee and ensures a heart-loving strain on the operator.
-
Product
Debug Fixture
-
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
Product
Manual Ranging Digital Multimeter
UTLDM1
-
UEi Test & Measurement Instruments
The UTLDM1 is a CATIII 600V Manual ranging multimeter
-
Product
Manual Test Stands
-
AMETEK Sensors, Test & Calibration
This manual test stand is ideal for tensile testing, compression testing, peel, and flexural testing. It may be equipped with a quick-action lever or precision hand wheel for controlling crosshead speed and travel.
-
-
Product
2-kbit 12C EEPROM for Fixture Coding
FXA-101 I2C EEPROM
-
The FXA-101 is a 2-kbit serial I²C bus EEPROM used for identification of systems components. With it’s DIP switch it’s easily addressable. The FXA-101 may be glued directly to the appropriate component or inserted into a UMK housing from Phoenix Contact and installed on a DIN rail.
-
Product
INTERFACE TEST FIXTURE KITS
GENRAD 2270
-
Test-X GR Series CAM/TRAC® kits offer the same "Z" axis motion as the standard CT Series with the advantage of interface compatibility.Standard features include locking handle assembly, 3/8" FR4 probe plate, and 12 position I/O block interface..
-
Product
Manual Switch Boxes
-
RTI's manual switch box is a portable and versatile test solution for quick IC electrical verification tests. RTI's 96-pin manual switch boxes integrate with a variety of test configurations that are customized to your test and device needs. It requires no software and connects directly to an external power supply for bias test, and performs quick comparison tests using an A/B relay box.
-
Product
Vacuum Fixture Kits
-
*Perfect Sealing *Precise Operation *Stable Construction *Self Closing - Opening Covers
-
Product
Becker Transponder Test Fixture
TA-3400
-
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
Product
Test Fixtures
-
Pneumatically actuated Kelvin connection to custom manufactured device inserts either to complement ART's wide range of precision parametric test equipment or for use with third party measurement hardware.
-
Product
Guidance Laser with Manual Line Adjust
GL3000PM
-
The GL3000PM Guidance Laser uses an ultra high visibility green laser to establish visual line control. Used for highway paint striping, asphalt pavers, road wideners, pavement profilers, or virtually any application requiring vehicle line control. The GL3000PM is also particularly effective for gun carriage alignment on paint striping trucks.
-
Product
Functional Fixtures
-
Joule''s strength is in the design and manufacture of functional test fixtures. Using 3D modeling software to create the fixtures allows us to actuate pneumatics, open and close overclamps, actuate side access units - all before a single part has been machined for the fixture.
-
-
Product
Three Phase Manual Coupling/Decoupling Networks
CDN 3083 Series
-
Three phase 440 VAC/DC and 620 VAC/DC 100 and 200 A manual coupling/decoupling networks (CDNs) for Surge.
-
Product
Clamshell Type Mechanical Fixtures
-
Known in the ATE Industry as “Clamshell” type Test Fixtures, Semco’s Mechanical Test Fixture line is a cost-effective solution to test Printed Circuit Boards and Assemblies. This Test Fixture line is also available with the most widely used interfaces in the test industry.
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
OEM Manual Stage with Piezo Z-axis Top Plate
PZM-2000
-
Applied Scientific Instrumentation
The PZM-2000 consists of ASI's proven piezo top plate mounted within your existing OEM stage. This requires a completely new top plate be machined for the OEM stage, however, this allows us to provide an elegant solution.
-
Product
Collins Radar Fixture with Gyro Simulator
TA-3A/B
-
This weather radar test fixture is a combination of the established WXT-250 series fixture and the RDR-2000 and RDR-2100 radars so that a single panel will provide many features that are still required today. The gyro simulator built into the panel is usable for either radar being tested and eliminate's plugging in any external simulator. The features for both product lines as shown in their respecting CMM's are provided on the panel so that full testing and alignment of these radars and their system components can be tested and/or evaluated. If you require any changes or other product versions please give us a call.
-
Product
Standard & Custom Test Fixtures
-
Both standard and custom Test Fixtures from OAI enable the user to integrate the solar cell with the I -V tester. Fixture configurations range from from simple hold down devices to temperature-controlled fixtures with front and back side contact. We invite you to contact an OAI Application Engineer for help with your fixture design. With our expert guidance, you can expect maximum performance from your I -V Tester and Solar Simulator.
-
Product
Clamshell Type Mechanical Fixtures
Series 11
-
The MT Series 11 dual well mechanical kits are an affordable solution to printed circuit board testing with the advantage of testing two devices. These can be similar devices, or devices that are used together in a functional test. The Series 11 Kits have the same available features and options as the Series 10 Kits.
-
Product
Manual Label-Free Molecular Interaction Analysis Machine, Flexible Research Platform
OpenPleX
-
Designed to meet the demands of biologists, biochemists and biophysicists, the OpenPlex is a flexible surface plasmon resonance imaging system.OpenPlex is your companion for the development of label-free and multiplexed bio-assays and molecule detection. It is a robust and compact system designed for simple use and high versatility. Its open format, dedicated sensor chips and manual operation enable numerous types of experiments to be explored without compromise, covering chemistry, biochemistry, physico-chemistry and biomolecular interactions.
-
Product
Manual Test Press Fixture
750/752 Series
-
RTI's manual test presses are compact, portable, all-inclusive, and easy to use. Single lever operation and 100% vertical compression makes the manual test press an ideal solution for PCB, hybrid module, and high pin count device-level testing when complex test requirements cannot be met with a test socket and breakout board alone.
-
Product
Non-Destructive Resonant Inspection Drop Test Fixture
RAM-DROP
-
The Drop Test Fixture, Model RAM-DROP, Resonant Inspection System, allows automated sorting and quality testing of small metal injection molded (MIM), powder injection molded (PIM), additively manufactured, and other small parts by using the Resonant Acoustic Method (NDT-RAM).
-
Product
Automatic Fixture Removal
S93007B
-
The S93007B automatic fixture removal (AFR) is the easiest way to remove fixture effects from non-coaxial device measurements and runs on the PNA/PNA-L/PNA-X Series B model network analyzers
