Audio Testers
See Also: Audio Test, Testers, Audio Test Systems
-
product
Flying Probe Testers
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
product
Digital (1kV up) H.V. Insulation Tester
6210A IN (Ranges: 0.5kV, 1kV, 2.5kV, 5kV)
Standard Electric Works Co., Ltd
Microprocessor-controlled. Four insulation test voltages. Insulation resistance; auto ranging on all ranges. Bargraph indicates test voltage; rise and decay can be observed during tests. Visual and audible warning if external voltage is present. Fully protected: crow bar. Carry case. EEPROM calibration.
-
product
Modbus Simulator & Tester
Modbus Poll
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
product
Bench Mounted Tester
Flex 10
The Flex 10 bench mounted ATE is the smallest ‘standard’ tester in our range. The system comprises a single unit, measuring 600mm x 360mm x 660mm. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
product
Gas Chromatography Tester
Gas Chromatography Tester is designed to separate organic solvents. It is able to test solvent residues of printed packaging material, or the purity of a single solvent.
-
product
Field Sync Tester
Sentinel
All-in-one TesterPTP, NTP, SyncE and TDMMulti-port, simultaneous measurementsEmbedded GPS Rx and RubidiumHigh performance. Optional battery to maintain Rb in holdover during transit
-
product
DSE Wire Testers
DSE Test Solutions your gateway to a world of wire technology.We supply high-quality test equipment for the wire and cable industry. Our extensive range of intelligent test equipment is used for quality control and production optimisation of enamelled wire and cable.
-
product
High Insulation Digital Clamp Tester
HCL-5000+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Wide AC current measurements for 0.01A～500A.・Easy operation, Push to Open and Pull to Disconnect Mechanism.・Safe AC current measurements for high voltage circuit (AC80 to 7000V).・Auto power off function and Splash proof structure.
-
product
Brake Fluid Tester For DOT4
6512A
Peaceful Thriving Enterprise Co Ltd
The tester can be used as a digital brake fluid tester suitable for determining brake fluid quality. Quality is tested and indicated on 5 LEDs in terms of "percent of water in the brake fluid". Develop for professional use in automotive repair shops and in servicing.
-
product
HCAI-1 High Current Arc Ignition Tester
HCAI-1
The HCAI-1 High Current Arc Ignition Tester is according to IEC 60950-1:2001, BS EN 60950-1:2001, BS 7002:2000, GB 4943.1-2011
and UL746A, IEC60947.1: 1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-2008 and other standards required simulated safety test project. Parts and components of insulating materials or other solid combustible materials that are prone to flame spread in electrical and electronic equipment may ignite due to proximity or contact with electric arc, causing electrical fire and endangering the reliable operation of equipment and personal safety. -
product
LAN Cable Tester
21-6566-00
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus
-
product
Semiconductor Testers
Designing and manufacturing scalable Automated Test Equipment (ATE) targeted at testing SOC, MCU, RF PA/FEM, Sensors/MEMS and Power and Analog devices
-
product
EV And Pack/Module Tester
Discover the Series 8500, an innovative and fully automated test system engineered to evaluate the performance of Electric Vehicle (EV) components, Energy Storage batteries, Modules, and Packs in real-world conditions. This high-specification system not only delivers accurate results but also allows the energy produced during discharge to be returned to the electrical grid.Using Maccor’s standard fully featured battery test software, the Series 8500 can perform virtually any type of battery test including FUDS, SFUDS, DST etc. for electric vehicle batteries and standard cycling tests for energy storage devices.
-
product
CT Burden Tester
585
The 585 Burden Tester is a hand held unit rated for use up to 20A. The design features a digital LED meter for displaying the current transformer (CT) secondary current. The burden is applied for a specific length of time controlled by circuitry inside the unit to help prevent the burnout of the burden elements.
-
product
Continuity Tester
4102
Peaceful Thriving Enterprise Co Ltd
This product is designed to measure the continuity of electric circuits and components. The measurement result will be indicated by LED and buzzer. The illumination is very helpful when technician is working in dark environment.
-
product
Auto Contact Resistance Tester
KVHL
KV Hipot Power Test Equipment Co.,Ltd
KVHL Auto contact Resistance Tester with advanced large power switch power technology ang electric circuit is a special measurement instrument for testing the contact resistance of high/low switchs, cable wires and welds.
-
product
Shaft Voltage Tester™ Digital Oscilloscope
AEGIS®
Digital Oscilloscope and Multimeter with Conductive Microfiber Probe Tips. Is your motor safe from destructive shaft voltages? For the first time you can get all of the tools to find out in one place. The AEGIS® Shaft Voltage Tester™ Digital Oscilloscope bundle includes the AEGIS-OSC-9100 100 MHz digital osciloscope, shaft voltage probe tips, and a shaft grounding simulator. Armed with these tools, you can quickly and easily find whether your motors are at risk of premature bearing failure due to VFD-produced bearing currents.
-
product
Setaflash ‘Series 3’ Open Cup Tester
6910/2
The Elcometer 6910/2 Setaflash 'Series 3' Open Cup Tester offers the fastest and most accurate flash point instrument at a cost effective price.
-
product
Water Vapor Permeability Tester
QT-WVP
Qualitest Water Vapor Permeability Tester QT-WVP series is used to test the water vapor transmission rate (WVTR) of packaging materials.
-
product
Multi Function Automobile Tester
6521
Peaceful Thriving Enterprise Co Ltd
The multi-function automobile tester has LCD display to indicate the measured result. It has polarity detection with the LEDs for a positive and negative indication of DC voltage. For auto use, the functions included the measurement of DC voltage and current, signal frequency and max/min voltage, resistance and power providing testing.
-
product
CCTV Tester
M-IPC-200A
Fuzhou Metricu Technology Co Ltd
3.5 inch IP camera tester M-IPC-200A with analog, HD-TVI, HD-CVI, AHD
-
product
Trailer Light Tester with Ammeter
Checkmate 1200-A
An improved version of the Checkmate 1200, this reasonably-priced tester comes equipped with a 0-to-20-amp ammeter. It's capable of testing SAE trailers or RV's with electric brakes.
-
-
product
Trailer Light & Air Brake System Tester
Express Garage
The Express Garage Trailer Air and Electrical Systems Tester is a tool that anyone with even basic air brake knowledge can look at and instantly know how to use.
-
product
Buss Interface Unit Tester
BIUT 820
Quickly and reliably check any BIU with the BIUT-820 which provides comprehensive, fully automated testing in the field or at the shop.
-
product
Wafer/Chip/Package Semi-automated ESD Tester
400SW
Tokyo Electronics Trading Co., Ltd.
Semi-automated ESD tester featuring Ecdm 400E, Universal ESD Simulator. Used with a manual wafer probing system or a die manipulator, wafer or die level semi-auto ESD test can be done, as well as packaged device test. Damage is detected by V-I curve or leakage current change detection. Stress level and measurement points are programmed by personal computor via GP-IB. Once test terminals are selected, ESD endurance is automatically measured.
-
product
Digital Multi-Function Tester
MT2
Multi-functional tester with plain slot blade that allows the checking of wiring without dismantling or having any contact with live parts. Applications include 'break point' in wiring, continuity testing, bulb and fuse testing, microwave leakage, socket testing and testing for static. Fully insulated. Full instructional leaflet supplied. Supplied with 2 x 1.5V alkaline batteries.
-
product
Installation Tester
MT-300
Advanced multifunction installation tester for verification of electric safety of private and industrial electric systems
-
product
Electronic Ballast Tester
WT4000
• Measure parameter: 1) Input: Vrms, Lrms, W, PF, Hz, Phasic angle, total harmonic and 0-39 component of harmonic. 2) Output: Lamp voltage, Lamp current, Filament current, Guided cathodic current, Lamp power, crest factor and oscillatory frequency, single high frequency analysis. • Startup: Startup lamp voltage, lamp current, filament current, guided cathodic current curve and parameter, preheating time; • Simultaneously display on 8 windows for input and output parameters, convenient for comparison and analysis; • Test preheat energy, filament preheat time. And the parameters changes from 0 to 5s of filament voltage, filament current and filament power; • Up to 1MHz lrms test content to every EB; • Analysis symmetry of high Frequency curve of lout; • 12-bit high-speed A/D, sampling rate up to 10MHz, can easily analyse signal curve of output; • Finish an input and output testing at the same time within 1 minute; • Portable, can test, display, print without computer. Test report include data and curve, comply with international standard; • Communication port for PC, run under Windows98 or Windows2000, English Version available.
-
product
Gigabit Ethernet Tester
GET-100
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
