Conductivity
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
Designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment), ITU-T K21 and ITU-T K44.
-
Product
RF Attenuators
-
Home > Products > Test and Measurement > AttenuatorsBird - The RF ExpertsRF AttenuatorsBird manufactures a broad spectrum of devices from 2 W to 4000W. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators with a wide range of connectors and attenuation values.
-
Product
Low Temperature Gas Source
-
Get a low-cost means to introduce a gas without thermal pre-cracking using Veeco’s low-temperature gas source for molecular beam epitaxy (MBE) systems. The source features a large conductance tube for fast gas switching and a diffuser end plate for good growth uniformity. It is an ideal gas injector for CBr4 for carbon doping in GaAs and NH3 for GaN growth, as well as any other gases that do not require thermal pre-cracking. Enhance system capabilities further by combining the source on one mounting flange with an Atomic Hydrogen Source or 5cc Dopant Source.
-
Product
4-Wire Universal Cable/Harness Tester
LX-850
-
Shenzhen Lian Xin Technology Co., Ltd.
Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V·The system adopts the advanced four-wire measurement, and the minimum measurable range is 1mΩ.·The maximum test spot is 256.·640×480 full Chinese/English large color display .·All varieties of linearity and safety tests are available.·Fully programmable continuous test is available.
-
Product
IC Measurement Technology
Emission
-
is used to measure conducted emissions (measurements with direct 1 Ohm/150 Ohm-coupling) according to IEC 61967-4 at IC pins.
-
Product
Portable Thermal Conductivity Meter
TLS-100
-
The TLS-100 is a portable thermal conductivity meter used to measure thermal conductivity and thermal resistivity at the push of a button. Each TLS-100 comes equipped with a 100 mm sensor for testing soil, polymers, and other soft materials. An optional 50 mm sensor was designed for testing harder materials, like rock and concrete. The collected data is automatically analyzed, and results are displayed instantly.
-
Product
Salinity Concentration Pocket Water Meter
LAQUAtwin Salt-11
-
The only pocket meter that directly measures conductivity in 0.12ml sample and converts it into salinity or salt concentration. No need for a beaker to calibrate the meter or measure a sample. Just place few drops of the standard or sample onto the sensor. This procedure saves you time and prevents wasting your precious sample.
-
Product
400W to 600W - Single Output
CUS600M Series
-
*400W (600W Peak) Convection Cooled*600W with Forced Air*Medical Certifications (2xMOPP)*Class B Conducted and Radiated EMI*Suitable for Class I and Class II installations*Compact 3 x 5 x 1.46" size
-
Product
Centralized Warning Panel
MS 1116
-
The Centralized Warning Panel Test Rig is used for conducting Pre Installation Test of Airborne Centralized Warning display unit of Advanced Light Helicopter.
-
Product
Coupled Cavity TWTs
-
Communications & Power Industries
• Frequencies from 2.7 to 37.5 GHz• Peak levels: 500 W to 180 kW• Cooling type: air, liquid, conduction• Depressed or grounded collectors• CW (Continuous Wave) and Pulsed
-
Product
Corrosion Test Chamber
CME SF-CCT
-
CME SF-CCT chambers are designed to be flexible enough to comply with as many different CCT specifications as possible. These may be programmed to conduct a whole range of corrosion tests such as wet cycle, dry cycle, controlled humidity as well as the salt spray test in a single chamber. This can occur in any sequence and be repeated automatically. A wide range of optional accessories enable additional climates to be added to further extend the number of climates and conditions that can be created.
-
Product
Wires and Pipe Locator
LKZ-720
-
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
Product
Aluminum-Polymer
OS-CON™
-
Panasonic Industrial Devices Sales Company of America
Panasonic's OS-CON™ Aluminum-Polymer Solid Capacitors are available in both surface-mount and through hole types. These Solid Electrolyte Aluminum OS-CON™ Capacitors utilize aluminum and a highly conductive polymer material to offer low ESR, excellent noise reduction and ripple current capabilities. The OS-CON Series parts are characterized by a long-life and minimal ESR changes throughout the entire product line’s rated temperature range.
-
Product
Inducitive Switch Transient Test Circuit
NSG 5071
-
The basic philosophy of this test circuit is better reproducibility of actual switching transients. The reproducibility of this test circuit comes not from the output characteristics as in traditional conducted automotive immunity tests, but from a fixed design of the generator using several pre-defined components. Many of these components are defined in the standard as "critical" with no substitutions allowed. These components are used as required in the standard.
-
Product
Dissolved Ammonia Delivery System
DI-NH3
-
MKS' DI-NH3 is a compact, stand-alone system providing dissolved ammonia water. With Semiconductor 3D IC architectures using new materials like Cu-Co and Si-SiGe, the ability to wet clean with precise alkaline chemistries is growing in frequency and importance. The DI-NH3 delivers dissolved ammonia, providing optimal cleaning capability in an alkaline chemistry, minimizing material loss and contamination and inhibiting Electrostatic Discharge (ESD). Using closed-loop control, conductivity and pressure are kept stable under changing flow conditions. The dissolved ammonia concentration is monitored and adjusted, delivering the specific NH4OH concentration needed. Dissolved ammonia’s alkaline chemistry provides ESD protection during rinsing, particle lift-off, and residual photoresist removal in middle-of-line (MOL) and prevents corrosion of cobalt/copper interfaces.
-
Product
Waterproof Handheld Meter with pH electrode
CyberScan PCD 650
-
A Eutech Star Buy! Combining the strengths of all CyberScan 600 series meters, the CyberScan PCD650 is our top-of-the-line waterproof handheld that enables concurrent measurement of pH, conductivity, dissolved oxygen and temperature, all at the same time.
-
Product
PXI High Density MUX BRIC, 96-Chan, 10-Pole
40-570-416
-
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Coupling Decoupling Network
TBCDN-M1
-
The TBCDN-M1 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
Product
Electromagnetic Flowmeter for conductive liquids
Picomag
-
Reliable measurement and monitoring of industrial water, cooling water or warm water. Simultaneous measurement of flow and temperature. Flexible integration into all fieldbus systems via IO-Link. Commissioning and operation via Bluetooth® and SmartBlue App. Minimum conductivity ≥20 μS/cm. Fluid temperature –10 to +70 °C (+14 to +158 °F).
-
Product
Personal Grounding Tester
PGT120
-
Electronic test apparatus for checking personnel grounding systems such as electrostatic wrist straps and conductive footwear. The unit is equipped with two separate measuring circuits and is therefore capable of checking wrist straps and footwear separately or in parallel. The test result is signaled visually, acoustically (only if error is detected) and via contacts.
-
Product
CWDM Power Meter
OCC-50
-
OCC-50 Handheld CWDM Optical Channel Checker is specially designed for CWDM installation, maintenance and troubleshooting, which is able to measure and monitor power values of up to 18 CWDM channels. OCC-50 can replace high-cost spectrometers and conduct quick and reliable measurements in all environments. Thanks for its light, compact and sturdy design, OCC-50 is the ideal tool for CWDM installation and maintenance technicians.
-
Product
Semiconductor
-
Scientific Computing International
Materials which have a conductivity between conductors (generally metals) and nonconductors or insulators
-
Product
Water Conductivity Sensors
-
Water conductivity sensors are used in water-quality applications to measure how well a solution conducts an electrical current. This type of measurement assesses the concentration of ions in the solution. The more ions that are in the solution, the higher the conductivity.
-
Product
PXI 3A Power MUX BRIC, 9-Channel, 16-Pole
40-571-203
-
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Conductivity Sensor
-
Conductivity sensors from Aanderaa are compact, fully integrated sensors for measuring the electrical conductivity of seawater. Conductivity is a key parameter for in-situ measurements of several fundamental physical properties of seawater.
-
Product
EMI/EMC Testing
-
This type of testing is required for devices, systems, and applications within the military and aerospace industries. Weapons, aircraft, ground and support equipment, electrical, and electronic systems must meet the established requirements.During electromagnetic interference the component's electrical circuit is affected due to either electromagnetic conduction or electromagnetic radiation from an external source.
-
Product
Universal Tensile Testing Machines
-
Dongguan Amade Instruments Technology Co., Ltd
Universal tensile testing machines are testing equipment that are used to conduct mechanical testings of static load, tensile, compression, bending, shearing, tearing, stripping, applied to plastic sheets, pipes, tapes, rubbers, electric wires, springs, sponges, fibers etc. Tensile test is performed to measure and analyze the physical performances of different types of materials and finial products, playing an important role in developing new materials and controlling products quality. From the perspective of function, universal tensile testing(UTM) machine is an omnipotent instrument Just as the name implies. Clamps or fixtures are interchangeable on the basis of different test pieces, enabling various testings to be carried out on one tensile testing instrument. Options of single-column stand or twin-column stand can be available based on the specimen’s tensile/compressive force and dimension. Computerized tensile tester is preferred rather than microprocessor version If users want testing results including curve graphics between time, force and displacement.
-
Product
pH/DO/Conductometer
867/856 Modules
-
With the 856 Conductivity Module and 867 pH Module, you can build your own, customized solution – whether you are analyzing large sample loads or multiple parameters, or you want to enjoy full freedom when it comes to method programming and applications.
-
Product
CTDs: Profiling
-
Profiling CTDs make continuous measurements as they travel through water. When lowered over the side of a ship or integrated with an autonomous vehicle, they map a vertical column of water's characteristics. Compared to moored CTDs, profiling CTDs account for dynamic errors introduced by moving through water and sample rapidly to generate a high-resolution dataset over a short period of time. Sea-Bird Scientific profiling CTDs are:*Designed to perform under unique dynamic conditions found on moving platforms.*Pumped and ducted for constant flow to match temperature and conductivity response.*Plumbed so measurements are made on the same sample of water with a predictable delay and predictable flow effects.*Built with a rugged design for shipboard and autonomous deployments.
-
Product
Fully Automatic 4 Point Probe System for Silicon Wafer
WS-8800
-
*Measurement of resistivity, thickness, conductivity(P/N) and temperature*Tester self-test function, wide measuring range*Thickness, measurement position and temperature correction function for silicon resistivity*Number of cassette station can be changed by customers request*Host (CIM) communication and SMIF or FOUP compatible
