Bus Analyzers
analyze and debug systems based on standard bus formats.
See Also: Serial Analyzers, PCI Analyzers, Bus
-
Product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
VME Bus Analyzer / Exerciser
VME650
-
The VME650 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to MBLT protocol.
-
Product
Bus Analyzer / Exerciser
VME850P2
-
The VME850P2 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P2 connector. This module allows the user to monitor and stimulate the A, C and D rows of the 160 pin P2 connector. Although the VME850P2 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P2 connector must be less then 5V in order to prevent damage of the analyzer.
-
Product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
ARINC 429 PMC Interface Module
PMC-429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
-
Product
PMC Bus Analyzer / Exerciser
PMC650
-
The PMC650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
ISA Bus Dual Redundant MIL-STD-1553 A/B Simulator / Analyzer / Tester
CIC101-4
-
Price: Request QuoteMIL-STD-1553 A, B Simulator/Analyzer/Tester ISA BUS Interface Card. The CIC101 can be used for Validation Testing,Production Testing, full bus simulation and monitoring, as ageneral purpose 1553 interface or a stand alone bus Analyzer. It provides precise message scheduling andmeasurements. Major and minor frame times areindependent of message sequences or retransmissions onerrors. The start of all command messages may be set to beindependent of message length, response time or length ofresponse. The CIC101 features a calibrated Message timingand low jitter RT responses.
-
Product
Bus Analyzer
FireSpy® 3422bT/3822bT
-
The FireSpy3422bT and FireSpy3822bT bus analyzers are DapTechnology's latest 3-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy3422bT/3822bT is the most advanced 1394 test equipment in the market. The FireSpy3422bT/3822bT in fact combine three FireSpy analyzers in one single instrument. They comprises a significantly more powerful on-board processor and improved connectivity to the host.
-
Product
PMC and PMC-X Bus Analyzer / Exerciser
PMC850
-
The PMC850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Bus Analyzer
FireSpy® 4430b(T)/4830b(T)
-
The FireSpy4430bT and FireSpy4830bT as well as FireSpy4430b and FireSpy4830 bus analyzers are DapTechnology's latest 4-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy4430b(T)/4830(bT) is the most advanced 1394 test equipment in the market. The FireSpy4430b(T)/4830(bT) in fact combine four FireSpy analyzers in one single instrument. They comprises a significantly more powerful on-board processor and improved connectivity to the host.
-
Product
Bus Analyzer / Exerciser
PCF650
-
The PCF650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
Bus Analyzers
-
The FireSpy 1394 and AS5643 Bus Analyzer definesnew standards for advanced data monitoring, recording,generation, simulation and scripting.
-
Product
Bus Analyzer / Exerciser
VME850P0
-
The VME850P0 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P0 connector. This module allows the user to monitor and stimulate the A, B, C, D and E rows of the 95 pin P0 connector. Although the VME850P0 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P0 connector must be less then 5V in order to prevent damage of the analyzer.
-
Product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
-
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
Product
Bus Analyzer / Exerciser
VME850
-
The VME850 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to 2eSST protocol. In addition to the VME bus, user defined signals on the P0 and P2 connectors are also analyzed and exercised with optional plug-in modules.
-
Product
8 CHANNELS ARINC 429 Simulator Analyzer Tester
CIC429
-
The CIC429 is a full featured, high performance Serial bus Simulator Analyzer Tester developed by Andor Design for test and simulation of ARINC 429 or similar Avionic buses. The CIC429 is designed as a 5/8 size plug-in card for an ISA bus. An on board microprocessor off loads the host by organizing the data in a predefined structure in the dual port RAM. Programming the CIC429 consists of changing this data, which can be done on the fly for real time applications
-
Product
ARINC825 Cards
-
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
Product
Bus Analyzer
FireSpy® 3430b(T)/3830(bT)
-
The FireSpy3430bT and FireSpy3830bT as well as FireSpy3430b and FireSpy3830 bus analyzers are DapTechnology's latest 3-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy3430b(T)/3830(bT) is the most advanced 1394 test equipment in the market.
-
Product
Bus Analyzer / Exerciser
PCF850
-
The PCF850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
PMC to PCI Adapters
-
The PMC to PCI, PMC to CPCI and PMC to PC/104+ adapters enable the use of the PMC650 or PMC850 bus analyzers in PCI, CompactPCI and PC/104+ systems. The PMC analyzer plugs onto the adapter and then the mated adapter and analyzer plug into a PCI, CompactPCI or PC/104+ system. These passive adapters route the bus signals from the analyzer to the bus with minimal trace length and impedance matching. The adapters provide the full 64 bit interconnect between the analyzer and the bus.
-
Product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
Product
MIL-STD-1553 PMC Interface Module
PMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Compact PCI Bus Analyzer / Exerciser
CPCI650
-
The CPCI650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
Audio Analyzer and Digital Audio Bus Module
DP-cPCI-5667
-
DP-cPCI-5667 is a 6U cPCI Audio Analyzer and Digital Audio Bus Module. This card implements low speed digital audio bus, high speed digital audio bus and audio analyzer features. It is used for general purpose analogue audio analysis and supports low speed digital audio bus and high speed digital audio bus protocols.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Bus Analyzer
FireStealth® FS810bN
-
DapTechnology’s FireStealth810bN with its non-intrusive bus monitoring technology is the world’s first “Stealth Mode” IEEE-1394b analyzer. The FireStealth IEEE-1394b analyzer is a bus monitoring device that is attached to the IEEE-1394b bus leaving the existing topology unaffected.
