OBD 2
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - 40 MS/s on 2 Channels
M2P.6541-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
2 Meter Long SCSI Cable with 100 Pin Connector
U2904A
Digital Cable
The Keysight U2904A is an accessory compatible and recommended to be used with the U2600A Series USB used with the U2600A USB Modular Digital I/O modules. The pin-outs of the U2904A is dependent on the USB Modular Digital I/O module that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2903A is to be used with.
-
Product
PXIe-1083, 5-Slot (5 Hybrid Slots), Up to 2 GB/s PXI Chassis
787026-01
Chassis
PXIe, 5-Slot (5 Hybrid Slots), Up to 2 GB/s PXI Chassis - The PXIe‑1083 features a high-bandwidth, all-hybrid backplane to meet high-performance test and measurement application needs. This PXI chassis features all hybrid connectors, 58 W power and cooling, and an integrated … Thunderbolt 3 MXI-Express controller.
-
Product
PXI Dual 16x8 Matrix, 2 Pole Switching
40-532-022
Matrix Switch Module
This high-density reed relay matrix with 256 crosspoints. This model is configured as a Dual 16x8, model 40-531 is configured as a 32x8. Both modules are available in a choice of reed relay formats: 1-pole, 2-pole and 1-Pole screened. The screened version can be used for switching coaxial signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules. For example, seven PXI modules will form a 224x8 Matrix, a total of 1792 crosspoints in a 7-slot PXI Chassis.
-
Product
Isolated Amplifier - 2 Channel, 50 Vpp
33502A
Amplifier
The Keysight 33502A is a dual-channel, high voltage output amplifier. It has an isolated analog front end with up to 50 Vpp (25 V) output voltage range. It is also a very low-distortion amplifier with < 0.01% @ 10 kHz and 40 Vpp. The 33502A is designed to work as a companion for function generators to offer low-distortion, higher voltage outputs.
-
Product
2 Ports 25GbE SFP28 Network Mezzanine Card
NMC-2501
-
1 x Intel® XXV710DA2, 2 x SFP28 slots, 1 x PCIe x8, Gen3, RoHS compliant.
-
Product
Active Probe, 2 GHz
N2796A
General Purpose Probe
The N2796A is a new generation of low-cost, single-ended active probe with the AutoProbe interface. The probe integrates many of the characteristics needed for today’s general-purpose, high-speed probing - especially in digital system design, component design/characterization, and educational research applications. Its 1MΩ input resistance and extremely low input capacitance (1 pF) provide ultra low loading of the DUT. This, accompanied with superior signal fidelity, makes this probe useful for most of today’s digital logic voltages. And with its wide dynamic range (±8 V) and offset range (±12 V), the probe can be used in a wide variety of applications.
-
Product
Multiplexer 2:1 With De-Emphasis 32 Gb/s
M8062A
Multiplexer Module
R&D and test engineers who need to characterize serial interfaces of up to 32.0 Gb/s can use the M8061A 2:1 Multiplexer with optional de-emphasis to extend the rate of J-BERT M8020A and J-BERT N4903B pattern generator. For the most accurate receiver characterization results, the M8061A provides four calibrated de-emphasis taps, which can be extended to eight taps, built-in superposition of level interference and Clock/2 jitter injection. The M8061A is a 2-slot AXIe module that can be controlled via USB from the user interface of J-BERT M8020A as well as N4903B.
-
Product
DL-HCM Series Accessories Kit with Probe Holder, Micro IC Grabbers (Qty. 2), and Y-Banana Adaptor
DL-HCM-Acc-Kit
-
60 V of common mode and 80 V differential input range with 1 GHz of bandwidth, make these probes ideal for lower voltage GaN power conversion measurements. The 60 V of common mode is well suited for handling any float of the battery and bulk/absorption voltage during charging, while the 80 V differential input range provide margin for any overshoot.
-
Product
PXI 4-Slot BRIC Matrix, 184x4, 1-Pole (2 sub-cards)
40-560B-021-184X4
Matrix Switch Module
The 40-560B-021-184x4 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 2 Amp, 0.5m, 250 Port
A500RMR-F-5C050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
CompactPCI 2 Slot 1U
-
1U, 19″ Rackmount system with hot removable CPCI 3U Power Supply, four Powerful Fans and CompactPCI Backplane. The system support 6U cards Front and Rear. Additional four fans are available for optimal Front and RTM cooling solution. The Backplane is compliant with PICMG 2.0 R3.0 with 64bit 66MHz & supports boards with hot swap capability PICMG 2.1 R2.0. All five CompactPCI connectors (J1-J5) are available on the backplane. The system slot is located on the lower-slot.
-
Product
USB-485/2, 2-Port, USB, RS485/RS422 Serial Interface Device
778476-02
Serial Interface
The USB‑485/2 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/2 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
60MHZ, 150 MS/s,16 kpts, 2 Channel, 20 Vpp Function/Arbitrary Waveform Generator
T3AFG60
Arbitrary Waveform Generator
Teledyne Test Tools T3AFG5 and T3AFG10 series Function/Arbitrary Waveform Generators are a new family of low cost, high performance, single channel Function / Arbitrary waveform generators offering a high level of functionality and an excellent specification at a very competitive price point.
-
Product
SIMRC - 8 x 2 Matrix 1-Pole
1030-R-8-2-1-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
Carrier Board
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
PCI 2 Amp Multiplexer, Single 32-Channel, 1-Pole
50-635A-101
Multiplexer Module
The 50-635A-101 is a single 32-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 2 Amp Multiplexer, Dual 16-Channel, 2-Pole
40-635A-006
Multiplexer Module
The 40-635A-006 is a dual 16-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
RF Electronic Calibration Module (ECal), DC/300 KHz To 7.5 GHz, 7-16, 2 Port
85098D
Electronic Calibration Module
The Keysight 85098D RF electronic calibration (ECal) module makes the calibration of vector network analyzers fast, easy, and accurate. ECal is a precision, single-connection calibration technique for your vector network analyzer. Performing a full two-port calibration takes less than half the time and a number of connections using ECal versus mechanical calibration kits. Furthermore, the accuracy of the calibration is comparable between electronic and mechanical methods. Traditional mechanical calibrations require intensive operator interaction, which is prone to errors. With ECal, the operator simply connects the ECal module to the network analyzer and the software controls the rest.
-
Product
PXI 4 Slot BRIC 88x4 1-Pole (2 sub-cards)
40-562A-021-88X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Power, Patchcord, ITA, 36", High Power, 2 AWG, to Ring Terminal (150 Amps)
7-222902688-036
Power Patchcord
Power, Patchcord, ITA, 36", High Power, 2 AWG, to Ring Terminal (150 Amps).
-
Product
Ultra-Low Noise 2 kHz Photoreceiver w/ Si-PIN Photodiode
PWPR-2K-SI
-
Picowatt Photoreceiver series PWPR-2K with switchable gain (10 to the 9th V/A, 10 to the 10th V/A) and a bandwidth from DC to 2 kHz is the perfect choice for cw-measurements, time resolved signal acquisitions and highly sensitive modulated measurements. Si and InGaAs models cover the wavelength range from 320 to 1700 nm.
-
Product
NGFF M.2 2280 SSD Module
SQF-SM8 830
-
SQFlash 830 M.2 2280 SATA SSD. Compliant with SATA III and SATA v3.2 standard. Supports 120 bit ECC correct per 2K Byte data. Quad core processor with stable throughput. Preserved pin on M.2 connector for Voltage Stabilizer support from main board.
-
Product
PXI 4-Slot BRIC Matrix, 2A, 2-Pole 110x4, 2 Sub-cards
40-566B-002
Matrix Switch Module
The 40-566B-002 is a 110x4 matrix with 2-pole switching and is part of a range of high-density large PXI matrix modules with the ability to switch up to 2 Amps or 300VDC/150VAC. They are available in 4 or 8-slot PXI sizes and are constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI 2 Amp MUX, Dual 8-Channel 2-Pole
40-635-106
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PCIe-6374, 4 AI (16-Bit, 3.5 MS/s/ch), 2 AO, 24 DIO, Multifunction I/O Device
785817-01
Multifunction I/O
The PCIe‑6374 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6374 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included DAQExpress™ companion software provides basic measurement and analysis, while the NI‑DAQmx driver provides the ability to create customized automated measurement and control applications.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 0.5m, 250 Port
A500RMR-500RMR-5C050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
Compact High-Performance IoT Gateway With NXP I.MX8M Quad Core Cortex A53, 2 LAN, 2 COM & 1 USB
ECU-150
-
NXP i.MX8M Quad Core Cortex A53 1.3G CPUDDR4 2GB RAM, 16GB eMMC for system storage2 x RS-232/485 isolated serial ports2 x 10/100/1000 Ethernet ports1 x Mini-PCIe for WIFI/Cellular/4GSupport web service for remotely on-line monitoringSupport SD card & on-line firmware updateSupport Modbus, IEC-60870-5, DNP3.0, OPC-UA, BACNet protocol （ECU-150-12A1&ECU-150-12A1U need container EdgeLink）Support Data logger on SD card
-
Product
PXI Dual 2 Channel (M Mode) SC 62.5 Cons
40-855-222-M62.5
Switch Module
The fiber optic switches connect the common to a channelby redirecting the optical signal into a selected output fiber.This is achieved using Micro-Mechanical Mirrors driven bya highly precise mechanism and activated via an electricalcontrol signal.
-
Product
500-Pin SEARAY Connector, Male With Backshell, 2 Amp, 250 Port
C500RMR-4SB-5C
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
