OBD 2
-
Product
PXI 2 Amp MUX, Quad 8-Channel 1-Pole
40-635-108
-
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 12-Slot BRIC Matrix, 92x8, 1-Pole (2 sub-cards)
40-560B-321-92X8
-
The 40-560B-321-92x8 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays
-
Product
Radiator Test and Repair Stand, Type 2 (Two Station)
9001
-
The Radiator Test and Repair Stand, P/N 9001, meets all requirements of military specification MIL-S-4534C, is completely self contained and requires only connection to a source of shop air and gas to place in operation.
-
Product
PXI Single 2 Channel Fibre Optic SC/PC
40-855-212
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
K-Type Thermocouples Wire, Fiberglass (32deg F to 900deg F) 2 m
745690-K002
-
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm - SPST
50-294-111
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
High Power, Contact, ITA, 150 Amps, 2 AWG
610150101
-
Primary mating contact 610149101. (May mate with other Receiver contacts, as well.)
-
Product
SIMRC - 8 x 2 Matrix 1-Pole Screened Relay
1030-R-8-2-1RF-5/1D
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 2 9-Pin Female D-Subs, for RS-232
540127010101
-
Cable Assembly, Receiver, TriPaddle, 20", 2 9-Pin Female D-Subs
-
Product
USB-6003, 8 AI (16-Bit, 100 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device
782608-01
-
8 AI (16-Bit, 100 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device - The USB‑6003 is a low-cost, multifunction DAQ device. It offers analog I/O, digital I/O, and a 32‑bit counter. The USB‑6003 provides basic functionality for applications such as simple data logging, portable measurements, and academic lab experiments. The device features a lightweight mechanical enclosure and is bus powered for easy portability. You can easily connect sensors and signals to the USB‑6003 with screw-terminal connectivity. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Thin Film Based Thermopile Detector: 2 or 1 Channels
DR46
-
A two-channel or a one-channel compensated thin-film thermopile in a TO-8 package. Each active area is 4mm x 0.6mm. Offers high output with excellent signal-to-noise ratio. An internal aperture minimizes channel-to-channel crosstalk increasing sensitivity.
-
Product
16 Bit Digitizer PCIe Gen-3 Oszilloscope, 2 Channels 1GS/s 4GS Speicher
RazorMax / CompuScope Express 161G2
-
The new extremely fast and high-resolution Gage digitizers of the series RazorMax Express CompuScope offer with a half long Single slot PCI Express card a resolution of 16 bit and a sampling rate of 1 GS/s (per channel).
-
Product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
782250-01
-
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Micro Power, Header Insert, Receiver/ITA, SIM, Right Angle, 2 Pos, 2 Slot
510181103
-
This header insert contains 2 right-angle micropower contacts and is designed for soldering directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 2 of the 34 slots in this module.
-
Product
CombiVolt™ 2 Voltage/Continuity Tester
DL6790
-
The three-in-one testers with a rugged, ergonomically formed housing for perfect handling.
-
Product
PXI 2 Amp Multiplexer, 1-Bank, 64-Channel, 1-Pole
40-657A-001-1/64/1
-
The 40-657A-001-1/64/1 is a 1-bank, 64-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Product
PXI 38 Channel 2 Amp Multiplexer Card
40-656-001
-
A 38-channel multiplexer, 2-pole switching, suitable for switching signals to 2Amp, 220VDC/125VAC. It offers the highest switching density in its class for medium power/ voltage signals. Specifically designed for switching POTS, ISDN or xDSL telephony signals. Bandwidth for most configurations is typically >25MHz. It is paired with a very similar module, 40-655-001, a multi-banked multiplexer.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 2 Channels, High Voltage Outputs
M2P.6571-X4
-
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
PXI-6225, 80 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO, PXI Hybrid, Multifunction I/O Module
779296-01
-
80 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXI‑6225 offers analog I/O, correlated digital I/O, two 32‑bit counter/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
1.5kV, 200 MHz, 2 pF, 10 M, Rise Time < 1.75 ns, High Voltage Differential Probe
T3HVD1500-200
-
1.5kV, 200 MHz, 2 pF, 10 M, Rise Time < 1.75 ns, High Voltage Differential Probe.
-
Product
SCSI-100 To 2*SCSI-50 Shielded Cable
PCL-10250
-
100-Pin to two 50-Pin SCSI-II CableHalf pitch 100 pin: Male gold flash contacts, black insulatorHalf pitch 50 pin: Male gold flash contacts, black insulator x 225 twist pairs tinned and strand copper wire with drain wireAluminum/Mylar foil and braided copper double-shielded cableP.V.C. jacketUL 20276 approvedColor : Black
-
Product
SQFlash EU-2 PCIe/NVMe U.2 2.5" SSD (SFF-8639), Enterprise Series
SQF-CU2 EU-2
-
U.2 (SFF-8639) PCIe/NVMe 2.5" SSD, Compliant with PCIe Gen.5 x 4 interface and NVMe Express 2.0. AES-256 Support & TCG-OPAL Compliant, Support LDPC with RAID ECC. Heat-spreading design with thermal solution, SMART and GUI management tool.
-
Product
PXI-6221, 16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
779629-01
-
The PXI-6221 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI Dual 2 Channel (M Mode) SC 50 Cons
40-855-222-M50
-
The fiber optic switches connect the common to a channelby redirecting the optical signal into a selected output fiber.This is achieved using Micro-Mechanical Mirrors driven bya highly precise mechanism and activated via an electricalcontrol signal.
-
Product
PMC Module With 2 Or 4 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation Of Avionic CAN Bus Systems
AMC825-x
-
ARINC825 (CAN bus) Test & Simulation module for PMC with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AMC825-x PCI Mezzanine Card (PMC) can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
PXI 2 Amp Multiplexer, 38-Channel, 2-Pole
40-656A-001
-
The 40-656A-001 is a 38-channel multiplexer with 2-pole switching, suitable for signals to 2 Amp, 220VDC/125VAC. It offers the highest switching density in its class for medium power/voltage signals.
-
Product
3.5" Embedded SBC With Intel® Atom® X5-E3940 Processor, HDMI, LVDS, 2 GbE LAN And Audio
CAPA311
-
*Intel® Atom® x5-E3940 processor*1 DDR3L SO-DIMM for up to 8GB of memory*2 USB 2.0 and 4 USB 3.0*2 full-size PCI Express Mini Card slots
-
Product
GPIB T8 Cable, 2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender
183164-100
-
2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender - The GPIB T8 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T8 Cable with a pair of GPIB extenders to increase the cable length of your system up to 2 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T8 Cable is offered in different lengths.
-
Product
PCIe 14 Bit High Speed Digitizer - 500 MS/s on 2 Channels
M4I.4450-X8
-
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PCI 2 Amp Multiplexer, Quad 4-Channel, 2-Pole
50-635A-109
-
The 50-635A-109 is a quad 4-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
