OBD 2
-
-
Product
Gigabit (PoE), 2 Port, Network Interface Card
Ethernet Network Interface Card
-
Gigabit (PoE), 2 Port, Network Interface Card
-
Product
Oscilloscope - 350 MHz, 2 Analog Channels
DSOX4032A
Oscilloscope
350 MHz2 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
Oscilloscope, Slim Body, 2 Channel, 30 MHz, 250 MSPS, 10 kpts, 11 ns
72-2580
-
The 72-2580 is a 2-channel 30MHz Oscilloscope with 8-inch color TFT display. This economic oscilloscope provides an user friendly interface with stable readings, making it perfect for the hobbyist, educator or occasional user. The large 8-inch color TFT display provides large and crisp readings.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 44 Pin ML DSub, (2) SMB Plugs, Twisted Pair
540149050101
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 44 Pin ML DSub, (2) SMB Plugs, Twisted Pair.
-
Product
1 GHz, 2 Analog Channels Oscilloscope
DSOX3102A
Oscilloscope
1 GHz2 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add memory, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Receiver, G2, 2 Module, Keying Feature, With Protective Cover
310120110
Receiver
The Receiver for the G2 is equipped with a locking handle and nickel plated steel slides that engage up to 480 contact points. It allows a high amount of I/O within a compact and rugged device. The Receiver is accompanied by a Protective Cover to use when the ITA is not engaged.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 131 Ohm With SPDT
50-293-134
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Pico-ITX SBC With Intel® Atom® X5-E3940 Processor, DisplayPort, LVDS, 2 GbE LAN And Audio
PICO319
-
The PICO319 is powered by the onboard Intel® Atom® x5-E3940 quad-core processor. The noise-free pico-ITX motherboard offers combinations of ruggedness, high computing capabilities and enhanced graphics capability in an extremely compact size of only 100 x 72 mm. Moreover, the board features 12V DC power supply input with AT Auto Power On function. A dual-display capability is available through DisplayPort and 18/24-bit single/dual channel LVDS ports. For extensive storage needs, this compact embedded motherboard has one M.2 Key B slot (22 x 42 mm or 30 x 42 mm) for SATA or PCIe x2 SSD card and one half-size PCI Express Mini Card slot in support of mSATA. The Intel® Atom®-based pico-ITX board comes with rich I/O connectors, including two USB 2.0 ports, two USB 3.0 (USB 3.1 Gen1) ports, one RS-232/422/485 port, one RS-232 port, one HD Codec audio, and 4-channel digital I/O. It also supports SMBus that is compatible with I2C for smart battery support. The PICO319 offers watchdog timer and hardware monitoring function for reliable operation.
-
Product
Infiniium UXR-Series Oscilloscope: 100 GHz, 2 Channels
UXR1002A
Oscilloscope
The UXR1002A is the 100 GHz, 2 Channel, UXR-Series Real-Time Infiniium Oscilloscope
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for six M.2 or NGSFF (NF1) PCIe SSD Modules
SKU-086-36
-
This Squid PCIe Carrier board can support up to six M.2 or NGSFF (NF1) PCIe SSD (solid state drive) modules, with M-key. Supported module dimensions are 2280 or 22110 in length, and a width of up to 32 mm. SSD modules of any capacity may be used, from any vendor, and in any combination.
-
Product
GPS Signal Splitter 16 Way, SMA Jack, 1 - 2 GHz, 50 Ohm Coaxial
GPS161
-
INSTOCK Wireless Components, Inc
Wideband Frequency (1000-2000 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA Max on DC Block PortsTri Alloy SMA Female (Jack) Low PIM
-
Product
Linear Testfixture (2 pcs. Cassette Included), UTT 105 x 170 mm (2pcs)
MG-05
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (1000N) 650 units for each cassette• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 105 x 170 mm (wxd) each cassette• Outer dimensions: 550 x 400 x 50 x 140 mm (wxdxh1xh2)• Designed for 2 pieces changeable cassette
-
Product
1 Or 2 Stream MIL-STD-1553 PMC Test And Simulation Modules With Prog. Coupling,onboard Bus Network And Variable Output Amplitude
AMCX1553-xT
-
MIL-STD-1553 Test and Simulation modules for PMC with 1 or 2 Dual Redundant streams plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
PXIe 2 A Relay Module, 52xSPDT
42-139A-201
Relay
The 40-139A-201 (PXI) and 42-139A-201 (PXIe) are 52xSPDT relay modules suitable for high density switching applications with medium power and feature 2 A current capacity with voltage rating to 300 VDC/250 VAC
-
Product
2 Channel Charge-Discharge Module 6 V, 100 A
BT2205A
Charge-Discharge Module
The BT2205A is a 2 channel charge-discharge module 6 V, ± 100 A, 437.5 W for module Li-ion cell formation and lifetime cycling solution.
-
Product
Medical Computer Equipped With MXM Graphics Module Supporting NVIDIA Quadro® GPU With 8th/9th Generation Intel® Core™ I7/i5/i3 In LGA1151 Socket. Compliant With IEC 60601-1/IEC 60601-1-2
MLB-3002
Industrial Computer
- 2x PCIe Gen3 x4 expansion slot for Full Height Half Length add on card, each slot is 25W power budget and additional Molex 4 pin power cable (12V/1.5A and 5V/2A) support- ADLINK MXM Graphics module support (Type A/B, up to 120W)- 8th/9th Gen Intel® Core™ i7/i5/i3, Celeron® processor- Dual SODIMMs for up to 64GB DDR4 non-ECC memory (dependent on CPU)- DisplayPort (2 from CPU, 4 from MXM)- 1x M.2 E key supporting 1630 or 2230 for Wi-Fi/Bluetooth module, 1x M.2 B key supporting 2242 or 2280 for SATA storage module- Reliable Molex type 12V DC-in connector- 1x Intel® i219-LM and 3x Intel® i210-AT
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 2 Channels
M2P.6531-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
CIRCUIT MODULE, Riser For ISMB 2U PCIe X16 Riser Card To 2 PCIx8 Expansion Slots, And PCI Card
AIMB-RP3P8-12A1E
-
Support ISG 2U chassis
-
Product
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs
510140111
Pull-Thru Adapter
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs.
-
Product
USB-6003, 8 AI (16-Bit, 100 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device
782608-01
Multifunction I/O
8 AI (16-Bit, 100 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device - The USB‑6003 is a low-cost, multifunction DAQ device. It offers analog I/O, digital I/O, and a 32‑bit counter. The USB‑6003 provides basic functionality for applications such as simple data logging, portable measurements, and academic lab experiments. The device features a lightweight mechanical enclosure and is bus powered for easy portability. You can easily connect sensors and signals to the USB‑6003 with screw-terminal connectivity. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
IntegraVision Power Analyzer, 2 Channels, 1-Phase AC
PA2201A
-
Achieve better power analyzer accuracyAddress multiple test scenarios with the flexibility of wide-ranging, isolated inputsVisualize transients, in-rush currents & state changes with a high-speed digitizerAnalyze voltage, current and power in the time and frequency domains12.1" touchscreen
-
Product
Robust Din-rail Fanless Embedded System With RISC-based (iMX-287) Processor 4 COM, 2 CAN Bus And DIO
rBOX610
-
The rBOX610 din-rail fanless embedded system utilizes the low power RISC-based module (iMX-287) processor and is designed to withstand temperatures ranging from -40°C to +70°C for using in extreme operating environment and industrial automation applications. The rBOX610 box PC features 4 RS-232/422/485 serial ports, dual LANs, 4 digital input channels,4 digital output channels, 2 CAN bus and 1 eMMC onboard 4 GB & 1 x SDHC socket for storage expansion (easy to access) in a compact, IP40 protected, industrial-strength robust case. Two power paths input minimize the risk of data loss in the event of a single power failure. Its vertical din-rail form factor makes it easy to install the system in a small cabinet. Due to the RISC-based architecture, rBOX610 will not generate a lot of heat while being operated. The ready-to-run rBOX610 is specially designed for remote control/monitoring management applications like unmanned control room, industrial machine, automatic parking lot, traffic cabinet and more.
-
Product
Composite 2×12 Video Distribution Amplifier 12VDC
VDA212RM-12
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
cRIO-9034, 1.91 GHz Quad-Core CPU, 2 GB DRAM, 16 GB Storage, and Kintex-7 325T FPGA, 4-Slot CompactRIO Controller
783453-01
Embedded Controller
1.91 GHz Quad-Core CPU, 2 GB DRAM, 16 GB Storage, and Kintex-7 325T FPGA, 4-Slot CompactRIO Controller - The cRIO-9034 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. Additionally, the cRIO-9034 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
CompactPCI 7U 2 Slot left justified, 64 bit, P1-2s
105CPCI702-0157R
-
CompactPCI 7U 2 slot 64 bit with system slot left, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1. User defined VI/O is standard.
-
Product
PXI 2 Amp Multiplexer, Quad 4-Channel, 2-Pole
40-635A-109
Multiplexer Module
The 40-635A-109 is a quad 4-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Fanless Embedded System With Intel® Core™ I7-6600U/i5-6300U/i3-6100U & Celeron® 3955U, 2 HDMI, 2 GbE LAN, 4 USB 3.0, 2 COM And PCI Express Mini Card Slot
eBOX560-500-FL
-
The eBOX560-500-FL is an Intel® Skylake-based fanless embedded system with compact size and full-featured I/O interface. To bring both excellent performance and ultra-low power consumption, the palm-sized embedded box PC is powered by the 6th generation Intel® Core™ i7-6600U or Celeron® 3955U processor (formally codename: Skylake). One 260-pin DDR4-2133 SO-DIMM socket with system memory up to 16 GB is available. The power efficient IP40 embedded system supports 12V DC input with screw-lock and features a user-friendly AT/ATX DIP switch. The compact eBOX560-500-FL is suitable for Industrial Internet of Things (IIoT) solutions, digital signage, retail equipment, smart factory automation, thin clients, industrial controller systems and many more.
-
Product
Oscilloscope 70 GHz, 2 Channels, 1 mm Inputs
UXR0702BP
Oscilloscope
The UXR0702BP is the 70 GHz, two-channel, 1 mm input Infiniium UXR-Series real-time oscilloscope.
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-01
Multifunction I/O
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
