Filter Results By:
Products
Applications
Manufacturers
Conducted Immunity
EUT's resilience to an injected disturbance through associated cable.
See Also: Immunity Test, Coupling Decoupling Network
-
product
Conducted Immunity Test System
Conducted RF immunity tests acc. to IEC/EN61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL-STD 461 CS 114 Signal generator,RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-caseStand-alone operation possible with optional available netbookControl-software includedMost important parameters are shown on an integrated displayAutomatic EUT-monitoringOperation via USB port of a PC or NotebookComplete range of CDNs available
-
product
RF Conducted Immunity Test System
RFCI61000-4-6
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
product
EMC Testing Services
Our sophisticated technology can meet the diversified needs of customers. Component Tests: Immunity, Radiated Immunity, ALSE, TEM cell, Bulk Current Injection, Stripline, Conducted Immunity, Transient Immunity, Power Supply Variations, Electrostatic Discharge Emissions, Radiated Emissions, Conducted Emissions, Transient Emissions. Vehicle Tests - Radiated Immunity, Radiated Emissions.
-
product
EMC Testing Knowledge & Equipment
Creating, delivering, installing, and training on EMC test systems; RF Immunity systems, RF Radiated and Conducted Emissions systems, Conducted Immunity and Pre-compliant EMC systems.
-
product
Immunity
EFT coupling
s used for direct-contact measurements of impulse immunity in IC pins, according to IEC 62215-3 and IEC 61000-4-4.
-
product
Immunity
ESD coupling
is used for conducted coupling of Langer ESD pulses (200ps rise time) into ICs.
-
product
Immunity Testing Systems
CIS Series
The CIS series test systems are configured to perform conducted immunity testing according to IEC 61000-4-6. The system includes an ACS series power amplifier, coupling/decoupling Network (CDN), directional coupler, 150Ω to 50Ω adapters, power attenuators, cables and [optional] CSAT software. These systems, when properly configured, are capable of testing your products to all levels given in IEC 61000-4-6 up to 230 MHz. You can choose from three systems. Follow the links below for detailed information, including a comprehensive datasheet listing system specs.
-
product
Conductivity Sensors
Conductivity sensors measure the specific conductance of liquid processes. The specific conductance is directly related to the presence of ionic species and their concentration. Barben Analytical offers a full range of two electrode and four electrode contacting conductivity sensors for a variety of industrial measurement applications.
-
product
Conductivity Meters
GAOTek conductivity meters report the conductivity of a substance as an inverse function of resistivity. Resistivity is measured in ohms/cm, while conductivity is measured in mhos/cm. Our portable conductivity meters and testers are ideal for water conditioning, medical, beverage, laboratory, and other industrial applications. Our high-performance conductivity meters are reliable, high quality, accurate and affordable equipment that facilitate easy inspection and testing. They are compact, portable instruments that allow a user to conveniently work in complex conditions in a lab or onsite.
-
product
Immunity
RF coupling
is used for the conducted measurement of the immunity according to IEC 62132-4.
-
product
Conductivity Sensor
ACF60-35
Knowing the conductivity of liquid samples is a key parameter to control product quality throughout the production process. The optek ACF60 conductivity sensor fulfils technical requirements of international regulations for reliable measurements ensuring quality and consistency.
-
product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
product
Transient Immunity Tester
KES7700
Transient Immunity Tester KES7700 Series are transient surge tester that utilizes a compact unit system. A surge generator circuit is installed for each pulse unit as the tester meets the requirement of ISO7637-2, ISO7637-3, ISO16750-2, JASO D001, SAEJ1113, and other standards. The KES7700 Series meets a broad range of independent automobile manufacturer standards as well.
-
product
Ultra-Compact Immunity Tester
AXOS5
The AXOS5 is an ultra-compact immunity tester that performs all the most commonly used transient immunity tests, including Surge, EFT, Dips/Interrupts and AC/Surge Magnetic Field. The simplified user interface provides quick selection of tests and test levels, and even lets you change test parameters “on the fly” while running a test.The actual EUT power mains voltage and current are indicated in the display. Using the Electronic-Fuse function, the user can set an upper limit for EUT power mains current. This feature is useful to protect the EUT from unnecessary damage.Whether you test to the IEC 61000 series “CE Mark” standards, the IEC 60601 Medical Device standards, or any number of telecom and product specific standards, the AXOS5 tester is your one stop test station for everything from precompliance to full compliance to product development testing.A wide range of cost-efficient Coupling / Decoupling Networks for symmetrical and asymmetrical data- and signal-lines is available as an option.
-
product
PH and Conductivity Meters
PeakTech Prüf- und Messtechnik GmbH
It is possible to measure the conductivity of liquids, for example of water. The purer the water, the lower the conductivity (for example, distilled water is purer than normal water and has a low conductivity of approx. <10 µS).
-
product
Thermal Conductivity Analyzers
Teledyne Analytical Instruments
Thermal Conductivity Analyzers by Teledyne Analytical Instruments
-
-
product
Conductivity Type Tester
HS-HCTT
It is strictly designed according to the requirements of the hot-probe thermal EMF conductivity type test in standard ASTM F42: Standard Test Methods for Conductivity Type of Extrinsic Semiconductor Materials. A temperature controlling heating element is installed inside the hot probe so that the hot probe is heated automatically and its temperature is maintained in the range 40-60℃.
-
product
Conductive Emission Measurement
Holland Shielding Systems B.V.
On site testing for exposure limits in working conditions to any international standard. This involve pacemakers and HSE Heath and safety executive, invitarisations worldwide.
-
product
Shielding Effectiveness/ Conductivity Test
EM-2107A | 30 MHz – 1.5 GHz
The EM-2107A is a standard test fixture for evaluation of the electromagnetic shielding effectiveness of planar material. The fixture is an enlarged section of coaxial transmission line and complies fully with the requirements of ASTM test method D4935-1. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred. The EM-2107A is provided with a reference standard test specimen, a dynamic range specimen. Dynamic range of greater than 80dB is achievable, although the cables and other test system components usually establishes the limiting factors.
-
product
Thermal Conductivity Measuring Device
TCM1001
In recent years, there has been a demand for small and thin electronic products such as mobile devices, and printed circuit boards are shifting to thin, multi-layered, and even modularized printed circuit boards. effect of bonding materials, that is, the ability to easily conduct heat, is emphasized, and testing equipment that evaluates thermal conductivity is required .As a business of our company, we have mainly manufactured and sold test equipment for solder wettability tests and solder bonding strength, but there was a need to urgently develop next-generation bonding material test equipment to replace these. Under these circumstances, we received a request from an academic research facility to manufacture a device that can measure the thermal conductivity of conductive adhesives under research and development, and we were able to obtain an opportunity to develop the device. We proceeded with the development based on these requirements .
-
product
Portable Thermal Conductivity Meter
TLS-100
The TLS-100 is a portable thermal conductivity meter used to measure thermal conductivity and thermal resistivity at the push of a button. Each TLS-100 comes equipped with a 100 mm sensor for testing soil, polymers, and other soft materials. An optional 50 mm sensor was designed for testing harder materials, like rock and concrete. The collected data is automatically analyzed, and results are displayed instantly.
-
product
Conductivity Switches
B/W Controls offers a simple conductivity holder and electrode that can be configured for multiple measurement points.
-
product
5lb Conductive Rubber Electrode
PRS-801W
Probe to test resistance of floors, worksurfaces, floor mats, or other flat objects.
-
product
EFT Immunity Measurement
EFT61000-4
EFT immunity tester EFT61000-4 is specially designed according to the characteristics and requirements of EFT measurement and it is an ideal disturbance source of EMS measurement. They have fine performance, such as high stability, high reliability, easy to use etc. It meets the standard requirements of IEC 61000-4-4, EN 61000-4-4, GB/T17215.301, GB/T17215.322 and GB/T17626.4. EFT61000-4 has LCD display in both English and Chinese.
-
product
Software for Immunity Test METES-EMS series
METES-EMS is software for Automated Test Solution to meed Immunity Std. each for Keys : Support for latest Windows OS Access via USB/LAN interface to measurement equipments to achieve
-
product
Conductivity Meters
There are both standard and a waterproof conductivity meter, as well as a conductivity meter available for flowing water or pure water (highly recommended for specific industries) as well as the ones with different conductivity measurement ranges. An important factor is that a conductivity meter normally measures electric conductivity in µS/cm, however it can also take measurements in mg/l (for direct reading of content in dissolved solid substances). The relation is established as follows: 2 µS/cm = 1ppm (parts per million) = 1 mg/l. Compensated temperature in the conductivity meter can be automatic or by hand.
-
product
Pocket Conductivity Testers
Labodam pocket conductivity testers are equipped with platinum sensors and 1 point brush calibration system. These easy to use pocket conductivity meters come with waterproof design features for protection against harsh conditions. The conductivity meters can be used for measuring the conductivity of drinking water, waste water, brine water, and liquids with high, low conductivity.
-
product
Conductivity Water Pocket Meter
LAQUAtwin EC-11
The only pocket meter that directly measures conductivity in 0.12ml sample. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the sensor. This procedure saves you time and prevents wasting your precious sample.
-
