Custom Fixtures
-
Product
Test Fixture (SMD Components)
16034E
Test Fixture
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
Product
Custom Transmitter Modules
AMC and TX
-
Transmit systems are designed for either high-power or broadband operation.
-
-
Product
ARINC HSI / ADI Test Fixture
TA-2000
-
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
Product
Edge Connector Fixture
EDGE
-
An edge connector fixture can be a low cost alternative to a bed of nails fixture. The most important features of this Edge Connector Tester is its portablility, ease of use, intuitive control functions, and durability in a production environment.
-
Product
In-Circuit Test (ICT) Fixtures
Test Fixture
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
Product
Functional Fixtures
-
Joule''s strength is in the design and manufacture of functional test fixtures. Using 3D modeling software to create the fixtures allows us to actuate pneumatics, open and close overclamps, actuate side access units - all before a single part has been machined for the fixture.
-
Product
Custom Pogo Pin Rings & Blocks
-
Reduce your cost-of-test with our pogo pin blocks and interfaces that transform complex DUT boards or breakout boards into universal motherboard-style interfaces. Eliminate the need to purchase or build a new board for every unique device, unit, or package.
-
Product
Press - Down Fixture Kits
-
*Supports most press - down testers *High - Quality *Precise & Reliabe
-
Product
Custom Products
-
As your partner for motion control, we offer solutions including customization, engineering and support. So, when it comes to your requirements, don’t settle. Get precisely what you need.
-
-
Product
Actuation Methods for In-Circuit Test Fixtures
-
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
Product
MIPI Test Fixtures & Software
-
The UNH-IOL has been a contributing member of the MIPI Alliance since 2007 and tests all mobile devices looking for MIPI conformance and physical layer testing including C-PHY, D-PHY, DSI, and CSI-2. All UNH-IOL MIPI Test Fixtures and Tools are available to member and non-member companies. Below are just some of the MIPI Solutions we offer. For a full list please visit our MIPI Test Fixtures page.
-
Product
Specialized Machines And Custom Test Stands
-
PSE AG has been developing test stands for many years for a wide variety of clients and uses. If you don’t see exactly the specialized test stand you need for your innovative research, we will design and develop it for you. The following are some examples of test stand solutions that we have developed in cooperation with research institutes and industry clients:
-
Product
High Speed Spin Fixture
1571P Series
-
The Model 1571 High Speed Rate Table System is designed to provide a precision high velocity testing solution for the development and/or production testing of inertial packages or their components.
-
Product
2-kbit 12C EEPROM for Fixture Coding
FXA-101 I2C EEPROM
-
The FXA-101 is a 2-kbit serial I²C bus EEPROM used for identification of systems components. With it’s DIP switch it’s easily addressable. The FXA-101 may be glued directly to the appropriate component or inserted into a UMK housing from Phoenix Contact and installed on a DIN rail.
-
Product
Universal Test Fixture
CAM/GATE
-
The Low Cost Solution for Accurate and Dependable Universal Functional TestThe CAM/GATE ® Universal Test Fixture System is your afforable, efficient solution for functional test. No need to have multiple fixtures in your test area...
-
Product
Cable Continuity Test Fixture
CCT
-
6 and 8 Wire Cable Continuity Test Fixtures For convienient desk top and bench top The most important features of this cable continuity tester is its ease of use intuitive control functions and durability in a production environment.
-
Product
Clamshell Type Mechanical Fixtures
Series 10
-
Semco MT Series 10: An affordable solution for testing of printed circuit boards.
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
Product
Cryogenic Millimeter-Wave / Microwave Test Fixtures and Calibration Kits
upj10
-
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
Product
Drop-In In-Circuit Test Fixtures
The Chameleon
-
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
Product
Custom Sensing And Imaging Solutions
-
Micro Magnetics has a proven track record of excellence in designing and developing new products and solutions based on our knowledge of magnetic devices and materials. We offer specialized solutions to meet our customers? unique needs. These solutions include single magnetic sensors, sensor arrays, custom electronics and packaging solutions, sensor processing (polishing, dicing, and lapping), and custom film and device deposition.
-
Product
Customized Solutions
-
The design of customer-oriented of systems for scientific experiments in the field of attosecond physics, is a dedicated area of expertise of UltraFast Innovations. We offer thorough consultation in the design phase and reliable and expedient construction according to customer requirements.
-
Product
Custom Engineered Motion Systems
-
Customizing our products and creating new motion designs for a specific application are at the heart of our business. With more than 50 years of experience, we’re the leading manufacturer of custom motion systems and equipment across a broad range of applications and industries. Whenever you integrate a customized Aerotech product or subsystem into your larger system, you can be confident that motion and precision will never be limiting factors in your success.
-
Product
Customized Cards & Modules
-
Tap into the resources of both a world-class electronics manufacturer in Molex, and a proven Engineering team that has been designing complex FPGA products since 1993. It’s a unique combination. Our experienced staff, IP, processes and facilities are the ingredients of a world-class design and manufacturing partner that our customers value for their most important projects.
-
Product
Custom & OEM Products
-
Applicos can provide custom hardware and software for many applications within the Analog/Mixed Signal area. We offer a unique combination of full-service assistance throughout the entire product realization process, from conceptualization to prototyping and manufacturing.
-
Product
Custom Lens USB 3.0 Camera Board (Color)
See3CAM_CU130
-
See3CAM_CU130 is an Ultra HD USB camera board based on Aptina™ AR1820HS sensor. It streams Ultra HD (3840x2160) at 30fps over USB3 in compressed MJPEG format, Full HD (1920x1080) at 30fps and HD (1280x720) at 60fps in both uncompressed and compressed MJPEG formats. This Custom Lens camera board is also backward compatible with USB 2.0, although in USB2, this camera supports fewer resolutions at lower frame rates.
-
Product
Manual Fixture Kit
230373 – CMCSK-04-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Customized Testing
-
Independent Testing Laboratories
ITL specializes in providing custom testing. Let us help you with designing your next R&D project.
