Dividers
-
Product
Power Dividers
-
Powers plitters can divide one signal into two or N way equal or non-equal energy, in reverse,they are also used as combiners by combining multiple signal into one. They are mainly used in feed network in antenna array, mixer and balanced amplifier, finish the work of distributing, combining and measuring power, isolating signal sources and measuring swept reflected coefficient etc.
-
Product
Power Dividers
-
We currently offer coaxial resistive power dividers (aka power splitters), which are inherently broadband and have excellent low frequency response (0!) albeit with poor isolation; and also Wilkinson Power dividers, aka Wilkinson Splitters. We have as connector options SMA, N, 1.95mm, & 2.92mm. Our power dividers cover DC-70Ghz. While most of our power dividers are 2-ways, we also have 3, 4, & 8 way dividers. The resistive power splitters are implemented with tiny resistors. Wilkinson splitters can be microstrip or stripline. RF Power Dividers are often lumped element, Microwave Power Dividers are often microstrip.
-
Product
Analog Multipliers & Dividers
-
An analog multiplier/divider is a device that produces an output voltage or current that is proportional to the product of two or more independent input voltages or currents. In addition to multiplying and dividing, multipliers can perform squaring, square-rooting and modulation functions. Applications include radar, communications, and industrial controls where a real-time response is required. Analog Devices’ offers the widest selection of multipliers and dividers.
-
Product
Frequency Dividers
-
These instruments feature a simple front-panel interface and provide low-jitter frequency division. A reset input (and manual switch) provides a method of synchronizing a high-speed input pulse train with lower-speed devices on the output.
-
Product
Voltage Dividers
-
Measurements International Ltd.
A series of resistors or capacitors which can be tapped at any intermediate point to produce a specific fraction of the voltage applied between its ends.
-
-
Product
Power Dividers/Combiners
-
Macom Technology Solutions Holdings Inc.
MACOM’s power combiners and dividers are used in aerospace and defense, wireless, and wireline communications applications. These devices can also be used for broadband CATV applications. They are available in a variety of connectorized and surface mount packages. Available in subsets operating between the 400 kHz to 26 GHz frequency range, our dividers and combiners are characterized as both 50 and 75 ohm devices
-
Product
DC Blocking L-Band Splitters, RF Power Dividers
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless offers DC-blocking power divider / combiners optimized for L-band power splitting applications. Standard configuration includes DC pass on one port to power a remotely located active antenna. Additional models available blocking DC to all ports. All models pass the 10 MHz reference signal through all ports.
-
Product
High Voltage Dividers
-
Ohm-Labs manufactures precision resistive high voltage dividers. By individually characterizing each resistor in the divider, voltage and power effects are minimized.
-
Product
Couplers & Power Dividers
-
*High power handling 750W Ultra-broadband devices support from 555 to 3800 MHz*Very low PIM <-160 dBc with low insertion loss*Outdoor rated unit with support for 7-16 and 4.3-10 connectors*Designed and produced to ISO 9001:2008 centrfication standards for reliability and quality
-
Product
6-Way Power Dividers From 0.4 To 22 GHz
-
Pulsar Microwave manufactures 6-way power dividers in connectorized packages spanning 400 MHz through 22 GHz. These narrow and broadband models are designed to operate in a 50-ohm system and are rated at 30 watts. The 6-way connectorized power dividers are available standard with wither SMA or N female connectors, though other configurations of BNC, TNC, F and male connectors are possible.
-
Product
MLDD 8-Way Power Dividers
-
KRYTAR MLDD 8-way power dividers lend themselves to emerging wireless ultra-broadband designs and many test and measurement applications. KRYTAR’s power dividers offer the widest frequency coverage in a single package on the market and provides superior performance. Targeting broadband electronic warfare (EW) systems and complex switch-matrix applications, for example, KRYTAR has used its proprietary design to produce a wide assortment of matched-line directional dividers (MLDD) with ultra-high performance over a broadband frequency range. Our 8-way power dividers can also be manufactured to meet military specifications.
-
-
Product
Power Dividers
-
Teledyne RF & Microwave offers several In-Phase Two-Way Power Dividers with high isolation, low insertion loss, excellent phase and amplitude balance in a small size for a variety of communications applications.
-
Product
12 / 16 / 32-Way Power Dividers From 0.5 To 8.5 GHz
-
Pulsar Microwave manufactures N-way power dividers in connectorized packages spanning 500 MHz through 8.5 GHz. These narrow and broadband models are designed to operate in a 50-ohm system and are rated at 30 watts.
-
Product
Low Frequency 2-Way Power Dividers To 3000 MHz
-
Power dividers from 4 kHz to 3 GHz are available from Pulsar Microwave in connectorized packages with SMA-female connectors, standard. This series is designed to handle 1 watt input power. They are designed for use in 50-ohm systems, and cover frequencies for VHF, UHF, Cell and PCS applications.
-
Product
2-Way Power Dividers
-
KRYTAR 2-way power dividers lend themselves to emerging wireless ultra-broadband designs and many test and measurement applications. KRYTAR has used its proprietary design to produce a wide assortment of matched-line directional dividers (MLDD) with ultra-high performance over a broadband frequency range. Our 2-way power dividers can also be manufactured to meet military specifications.
-
Product
Coaxial Power Dividers
-
A coaxial 2-way power splitter with a typical insertion loss of 1.2 dB at each output port and a typical isolation of 16 dB across the frequency range of 1 to 18 GHz. The power splitter has a nominal power handling of 30 W (CW) and a typical amplitude unbalance of ±0.4 dB. The return loss for all ports is 13 dB typical. The RF connectors of the power splitter are female SMA connectors.
-
Product
DAS / 4G LTE Power Dividers, Combiners
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless offers wideband RF power divider / combiners optimized for DAS (Distributed Antenna System), 3G, and 4G LTE modem gateway splitting applications. INSTOCK cell-band and DAS splitters are commonly used for in-building wireless (IBW) network deployments. Available in 2-way thru 48-way configurations spanning 698-2700 MHz with exceptional performance. Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
-
Product
VCOs with Output Dividers
-
Analog Devices offers a range of GaAs inGaP heterojunction bipolar transistor (HBT) MMIC VCOs with output divider options to meet your application and design needs. Members of this product line integrate resonators, negative resistance devices, and varactor diodes, while featuring excellent phase noise performance.
-
Product
2-Way Power Dividers From 0.23 To 70 GHz
-
Pulsar Microwave manufactures a large selection of 2-way power dividers in narrowband and broadband configurations, covering frequencies from 225 MHz to 70 GHz. They are designed to handle from 10 to 30 watts input power in a 50-ohm transmission system. Microstrip or stripline designs are utilized, and optimized for best performance.Units come standard with SMA or N female connectors, or 2.92mm, 2.40mm, and 1.85mm connectors for high frequency components.
-
Product
Power Dividers
-
Power dividers designed, manufactured and marketed by BroadWave are found in applications that include complex telecommunication lab configurations, test equipment, phase arrays and specific test modules.
-
Product
Handheld Micro-Ohmmeters
RMO-H Series
-
The RMO-H is battery operated and handheld micro-ohmmeter. It is designed for a variety of applications for contact resistance measurement of non-inductive test objects. Typical applications are accurate testing of:medium and high-voltage circuit breakers,disconnecting switches,high-current bus bar joints,cable splices,and different high-current links.Even more, it accurately measures in high-induction filed environments and substations, as well as in factory testing.RMO-H Series contains six models in total, divided in 2 sub-series depending on the test leads length requirement and the battery type:RMO-H1, RMO-H2 and RMO-H3 models are intended for use with short cables (e.g. 1,3 m / 3 m / 5 m). The 1-cell Li-Po battery with 8200 mAh capacity provides output voltage up to 4,1 V DC.RMO-H21, RMO-H22 and RMO-H23 models are ideal for applications where test leads with lengths > 5 m are required. The high output voltage (up to 8,3 V DC) is provided by 2-cells 4100 mAh Li-Po battery.The test current is regulated and can be selected in a range of 1 A to maximum 300 A, depending on the maximum test current rating:RMO-H1, RMO-H21 models – up to 100 A DCRMO-H2, RMO-H22 models – up to 220 A DCRMO-H3, RMO-H23 models – up to 300 A DC.Unlike many other handheld micro-ohmmeters available on the market, our instruments have regulated and user-selectable test currents. Therefore, RMO-H instruments generate an automatically regulated test ramp with stable and ripple-free current during measurement. These revolutionary characteristics in a handheld micro-ohmmeters technology are possible by using sophisticated Li-Po batteries. Consequently, modern battery technology enables you to do multiple measurements, and a full day of testing without recharging the battery.With all RMO-H models, it is possible to make tests on Both Sides Grounded testing objects, in an increased safety environment. Finally, these features in combination with a user-friendly interface (1-click to measure) significantly speed-up testing procedure and make it safer.These instruments store up to 1000 measurements on the internal micro SD card.Our free DV Win software communicates with the RMO-H micro-ohmmeters via a wireless Bluetooth interface. Furthermore, it allows you to download test results, analysis and generate fully configurable test reports.
-
Product
Digital Surge Tester
KT-905D
-
Surge Tester of KAST is divided for the use of 3¡40 §Ç by output voltage, and subdivided into type C of manual decision type, type A of auto decision type, type L of exclusive use for low inductance product test and type P loading printer which can printout its wave form and digital scope. Surge test requires only 0.5 second. Because Surge tester already performs 30 times of Impulse voltage test only for 0.5 second. Turn-to-turn short : phenomenon shorted between the side coils.
-
Product
High-Speed A/D 14-Bit Digitizers
Digitizer
GaGe 14-bit resolution digitizer models divide the input voltage range into 16,384 different digitization levels, which improves the delectability limit by a factor of 4 over the 4,096 levels of a 12-bit resolution digitizer model.
-
Product
Power Dividers & Splitters
-
Keysight dividers and splitters are used in a wide range of applications, such as: transmission line fault testing, power combining, source leveling, ratio measurements, power splitting, and critical signal processing applications that require minimal insertion loss and high port isolation.
-
Product
UHF/RFID/TETRA Power Divider Combiners
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless 350-1000 MHz RF power divider combiners are optimized for UHF, RFID, and TETRA power splitting and combining applications. Wireless microphone systems also typically operate in UHF frequencies, making an INSTOCK device ideal for splitting or combining antennas in UHF wireless microphone systems. Available in 2-way thru 48-way configurations with Type N, SMA, TNC and BNC connector configurations INSTOCK.
-
Product
DC - 12 GHz High Efficiency GaAs HBT MMIC Divide by 2 Prescaler
HMMC-3022
-
The HMMC-3022 is a DC - 12 GHz divide by two prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
Product
Low Profile PCI Express 8-Port
7803e
-
The 7803e low-profile PCI Express serial interface provides eight RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize 16C954 UARTs with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
