WAN Emulators
-
product
Relay Data Emulator™
SUBNET SEL
SUBNET SEL Relay Data Emulator Software can automatically learn a SEL relay’s communication capabilities. SUBNET SELRDE Software can then be directly substituted for the physical SEL relay to safely and reliably commission relay communications. Effortlessly change target and meter data through SUBNET SELRDE Software without the inconvenience or risk of physically jumpering contacts or using expensive and often unavailable test sets to directly inject voltage/current.
-
product
Channel Emulator
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
product
GAMA ARINC 429 Emulator
TA-429
ARINC 429 EMULATOR FOR GENERAL AVIATION (4th QTR) Unit will allow viewing multiple labels while receiving as well as when transmitting. Auto-increment when transmitting allows for more dynamic testing of equipment. All presented on a bright 4 line x 20 VFD.
-
product
Regenerative AC Emulator, 1200 VAC, 65 A, 90 KVA, 3‑Phase
SL1213A
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
product
Channel Emulator
ACE9600
The dBm Advanced Channel Emulator (ACE) is the most advanced non-terrestrial RF channel emulation solution to date. The emulated impairments include delay, signal Doppler, attenuation, phase offset, AWGN, frequency hopping, payload and multipath fading. The instrument can house up to four 600 MHz instantaneous bandwidth channels.
-
product
Scienlab Dual-Range Regenerative AC / Grid Emulator, 600 / 1200 VAC, 63 / 32.5 A, 90 KW / 135 KVA
SL1215A
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
product
Smart Network Emulation for All Mobile Device Tests
CMWcards
Use R&S®CMWcards to prepare the tests you always wanted, but never found the time to set up. Create wireless signaling and application tests on the R&S®CMW500 wideband radio communication tester just by setting up a hand of cards – no programming required. Revolutionary card wizards and unique game rules guide you through setting up test sequences that fully comply with test specifications. Thanks to the R&S®CMW500 tester’s unrivaled multi-technology capability, R&S®CMWcards can be used to rapidly reproduce signaling scenarios for various wireless communications standards.
-
product
Network Emulation, Delay Simulation, Bandwidth Emulator & WAN Simulation
GigaNet System’s network emulation appliances provide precision, performance and predictability in your test infrastructure resulting in optimized system performance and robust system behavior under real world network conditions.
-
product
Sensor Signal Emulator
This Sensor Signal Emulator is specially designed for Automotive Technicians to troubleshoot electrical control systems problems in the car. It simulates the signals generated from different sensors in the vehicle and the ECU which enables technicians to pinpoint the actual faults in the electrical control system in cases of doubt over their judgment of replacing the sensors or the entirety of the connecting wires to the ECU.
-
product
Host emulator
E84
Precision Development Consulting Inc
A USB controlled and self-powered emulator for functional testing SEMI E84 implementations. (E84-1000) This was developed because there was nothing like it in the marketplace, and it was clearly needed. This product enables a factory automation engineer to perform E84 functional testing anywhere in the world. Weighing less than 5oz, it is neither a burden, nor a power hog. You will never need to look for an additional power receptacle in the fab. The emulator gives the user full control over the sequence so that any test can be performed. Existing products were large and unwieldy, and provided canned tests that could not be modified to meet the requirements that Fab managers impose on their suppliers.
-
product
Car-to-X Signal Strength Emulator
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
product
Emulates AT8xC5122 Derivatives with 6/12 Clocks/Cycle
FE-5122
* Emulates AT8xC5122 Derivatives with 6/12 Clocks/Cycle * 32K Code Memory * Software Trace * Real-Time Emulation * Frequency up to 40MHz * MS-Windows Debugger for C and Assembler * Keil Vision2 Debugger Compatible * PLCC-68, PLCC-28, LQFP-32 and VQFP-64 Emulation Headers * Serially Linked to PC at 115Kbaud
-
product
Emulates Winbond W78ERD2
FE-WRD2
* Emulates Winbond W78ERD2 * 62K Code Memory * Real-Time Emulation * Frequency up to fmax at 5V * Windows Debugger For C/C++ And Assembler * 44-PLCC Emulation Header * Target Board and Programmer Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
product
ROM Emulator Instrumentation
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
product
Lightning "Emulator" Shield
SEN-39002
Arduino shield, ideal for AS3935 lightning sensor development. The lightning "emulator" generates a RF signal that mimics lightning strikes. This board is in an Arduino Uno form factor, and only uses GPIO and I2C, so can be stacked on many form factors (developed on an Uno and Mega).
-
product
Scienlab Dual-Range Regenerative AC / Grid Emulator, 600 / 1200 VAC, 63 / 32.5 A, 45 KW / 66 KVA
SL1214A
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
product
Emulation of the Mobile Wireless Environment from 2G to 5G
Base Station Emulator sUTP 5018
Bring a whole mobile network to your lab or production: NOFFZ Base Station Emulator (BSE) creates a customized cellular wireless environment. This makes testing wireless devices easier than ever before.Compact, cost-effective testing of multiple DUTs in parallel from 2G to 5G, including endurance testing for several days.
-
product
Physical Layer Switching Systems for Copper LAN, WAN< DSL, Telco Apps with RJ Style Connectors
RJ Series Switching Systems
The RJ Series of computer controlled switching systems are designed for physical layer switching of multiwire signals on RJ style connectors. Since the system uses mechanical relays it acts exactly like a piece of cable which makes it perfect for testing networks without altering the signals or regeneration.
-
product
Regenerative AC Emulator, 600 VAC, 63 A, 30 KVA, 3‑Phase
SL1201A
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
product
Emulator
GCI E84
The GCI E84 Emulator is the world's leading tester for development, implementation and qualification of products that must comply with the SEMI E84 Standard. It provides the industry-standard automated test plans that are utilized by virtually every 300mm FAB and equipment manufacturer worldwide. GCI testers are the only solutions that guarantee 300mm factory automation interoperability.
-
product
Regenerative AC Emulator, 600 VAC, 63 A, 45 KVA, 3‑Phase
SL1202A
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
product
Ethernet Cable Emulator
Upon different commands, it can simulate different network cable lengths, including 3 Modes: Bypass, Short, 100M. It can be used independently or jointly with other devices.
-
product
Adjustable ISI Channel Emulation Package for M8000 Series BER Test Solutions
M8070ISIB
Simplify receiver testing by offering unprecedented flexibility for handling test channels.
-
product
Propsim Channel Emulation Solutions
Propsim Channel Emulation Solutions are versatile and easy-to-use in a wide range of applications including MIMO, Beamforming, WLAN, Aerospace, MANET and MIMO OTA testing.
-
product
Fading Emulator
RI 241
RI 241 Fading Emulator is a radio channel emulator designed to replace the obsolete Agilent 11757B Multipath Fading Simulator.
-
product
Mobile Comm DC Source w/ Battery Emulation
66321B
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321B mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321B mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads.
-
product
PoE LLDP Emulation (PD) & Analysis for 802.3at & 802.3bt
802.3at and 802.3bt PD Emulation and Protocol Analysis
Integrated PoE LLDP and Load Emulation in a Single Instrument. IEEE 802.3at and 802.3bt LLDP Compliance Analysis. Independent, Per-Port 802.3at and 802.3bt LLDP Emulations. Flexible Single and Dual Signature PD LLDP Emulations. One-Click LLDP Protocol Capture and Analysis. Pop-Up Excel Spreadsheet Reports Assess Protocol Content and Timing. Enables One-Click Emulated Power-Ups and Standard Waveforms with LLDP Power Granting PSE's. Enables 2-Pair and 4-Pair PSE Conformance Test Suties with LLDP Capable PSE's. Enables 2-Pair Multi-Port Suite with LLDP Capable PSE's. Available for PSA-3000 and PSL-3000 Platforms.
-
product
Emulator
Is an advanced on-chip debugging emulator and flash programmer developed with the concept of greater efficiency in development. The combination of its high-speed downloading and various software and hardware solutions will contribute to reducing development times.
-
product
WAN Tester II
The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It is supplied with changeable nickel metal hydride batteries and a built-in charger.
-
product
Air Interface Emulator
Becker Nachrichtentechnik GmbH
With help of air interface emulators radio field propagations can be emulated reproduceable in laboratory environments. For different applications like cellular, wireless networks or broadcast several types of devices are available.
