Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Tinned Ends, 2m
A026HM5-T-0A200
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
i1 XL (High Power)
Ideal for high amperage applications. Single module offers 4 high power contacts in one connector. Removable backshell allows easy access to wiring for maintenance and probing.
-
product
Pulse generator
9355-1
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
product
Voltage Detectors
Non-contact voltage detectors can quickly detect live AC voltage. These handy devices are great for electricians to safety and quickly check the status of electrical wires.
-
product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
20-Pin GMCT Female Connector, 16A, With Backshell
40-960-020-16A-F
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 14 AWG. Also included is the backshell with screwlocks and cable clamp.
-
product
High density PCB connectors
MHD/MDD/MDP Series
Smiths Interconnect's MHD/MDD/MDP series is an ESA qualified, high density board to board and board to wire interconnect available in up to 400 positions, with available insulators to accommodate coax and power contacts.
-
product
PXI-4071, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter
778271-01
7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter - The PXI‑4071 is a high-performance 7½‑digit, 1,000 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXI‑4071 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXI‑4071 can acquire waveforms at sample rates up to 1.8 MS/s.
-
product
PXI RTD Simulator Module, 20 Channel, PT1000
40-263-103
The 40-263-103 is a 20-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
Pull-Thru Adapter, Wired, TriPaddle, 68 Pin ML VHDCI, f/ AIT PXI-C1553
510140197
Pull-Thru Adapter, Wired, TriPaddle, 68 Pin ML VHDCI, f/ AIT PXI-C1553.
-
product
Impulse Cable Tracer
Wayfind'r
The WAYFIND'R Impulse Cable Tracer was originally designed for electric utility use to accurately identify the route of buried secondary cables. Because the WAYFIND'R imposes an audio frequency signal on the cable, the signal is not induced into adjacent cables or pipes, eliminating false signals. The WAYFIND'R may also be used fro tracing indoor wiring and buried shielded primary cables.
-
product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 122Ω
40-252-012
The 40-252-012 is a programmable resistor module with 4 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-614A-002
510140253
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-614A-002.
-
product
Cable Assembly, 50-Pin SGMC, Female to Unterminated, Tinned Ends, 5A, 1m
A050FFR-T-0A100
This is a 0.5m long female to unterminated 50-Pin SGMC cable assembly with ferrules and is constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
product
4-Pin Power D-Type Cable, Male to Female, 0.5m
40-970-404-0.5m-MF
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
Serial Distance Display
TA903-03
This panel mounted or portable display will read Bendix/King serial distance as generated by their DME systems or GPS products. This long standing three wire format of CLK, DATA and REQ can now easily be displayed without the expense of a KTS143 test fixture. This product is ideal for shop and aircraft troubleshooting. The extruded aluminum enclosure is a standard DIN size(1/8) and the unit interfaces through a 25 pin D connector.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m
A025DM5-T-0A050
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Backshell, iCon, Receiver, with Large Cable Clamp
310113794
This receiver backshell is used with the iCon Receiver and is not mounted to a rack or panel. It provides protection for exposed wiring and is ideal for use together with the iCon ITA for cable-to-cable applications.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 2m, Screwlocks
A068SMR-C-6B200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
K-Type Thermocouples Wire, Fiberglass (32deg F to 900deg F) 2 m
745690-K002
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Ferrules, 1m
A068SMR-F-5A100
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
Internal Communications Platform
Messenger
Using Messenger from Trilogy, you can build a cost effective intercom solution without the installation, operational and future expansion constraints of more traditional 2 and 4 wire systems. From the factory configured Base System, Messenger evolves to suit the emerging communication needs of your organisation.
-
product
Tone Generator
140BMC/6P
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
product
CATx Surge Protector
SP-CAT5-6V
Protects sensors running on CATx unshielded twisted pair (UTP) cable against the effects of electrostatic discharge, faulty wiring and lightning. The use of two protectors on each end of the line will provide increased protection for each end against surges. Protected pins: (1,2) (3,6) (4,7) and (7,8) pass through. Impedance: 85 to 115 Ohms. Surge suppression: 22Vpeak @ 100A 10/1000µs. Maximum continuous voltage: 6Vpeak. Dimensions WxDxH: 1x3.6x0.9 in (25x91x23 mm). Regulatory approvals: GR 1089, NEC 800.100 and 830.100, ITU 703, UL94 V0 Flame Rated.
-
product
High Performance Cables And Accessories
Cables are designed and manufactured by Celadon. Cables are available in lengths custom to the half-meter, and can be manufactured with a variety of industry standard connectors, such as coaxial, triaxial, Type8, Edge 24/48 or 35/70, DSub 9, 15, 25, or 50; or advanced multi-contact. Depending on the overall size of the final product, an anti-abrasion sheath may be used to prevent wire wear.
-
product
PXI Millivolt Thermocouple Simulators
Series 41-760
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channelseach channel providing a low-voltage output across two connector pins capable of providing 20mV with 0.7V resolution, 50mV with 1.7V resolution and 100mV with 3.3V resolution, covering most thermocouple types. These thermocouple simulators use two wire outputs with a remote output reference sense to ensure the modules deliver accurate low-level voltages, even if the system has common mode voltages present. In addition, each simulation channel is also able to provide an open circuit setting to simulate faulty wiring connections to a sensor.
-
product
Proximity, Light, RGB, and Gesture Sensor
APDS9960
Add basic gesture sensing, RGB color sensing, proximity sensing, or ambient light sensing to your project with the Adafruit APDS9960 Proximity, Light, RGB and Gesture Sensor. When connected to your microcontroller (running our library code) it can detect simple gestures (left to right, right to left, up to down, down to up are currently supported), return the amount of red, blue, green, and clear light, or return how close an object is to the front of the sensor. This device uses an I2C interface so it's easy to wire up and use.
-
product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 10A, 0.5m
A020GMR-C-0C050
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
Tone Generator with Cable Tracer
1RA470
Cable tracer is designed to trace wires without damaging the instalations. It has wolume control to increase sensitivity. Power supply is standard 9V battery.
-
product
Stimulus Induced Fault Testing
SIFT
SIFT allows for the analysis of numerous stimuli to identify speed, fault, and parametric differences in silicon. The heart of the SIFT technique revolves around intentionally disturbing devices with external stimuli and comparing the test criteria to reference parts or timing/voltage sensitivities. Synchronous interfacing is possible to any tester without any wiring or program changes. The system can be based on either a motorized probe station or portable microscope stand for test head applications.
