Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
Product
Cable Assembly 44-Pin D-Type Female to Unterminated With Tinned Ends, 2m
A044HF4-T-0A200
Cable Assembly
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Super MUTT Deluxe Edition Electrical Circuit Tester
#9008-DL
-
Innovative Products of America
The Super MUTT places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation over both air brakes and lights. Built to facilitate a one-man testing operation, the Super MUTT reduces guesswork and inspection time to prevent failures that lead to expensive road calls and citations. The remote control allows for repetitive air brake actuation at each axle to reveal developing problems often missed by normal testing procedures.
-
Product
Wireless Bridge Device
BR-300AN
-
BR-300AN is a wireless bridge device which can easily convert a 10/100/1000BASE-T wired LAN device to a wireless LAN device. It supports a wireless LAN communication in the 2.4GHz and 5GHz bands and enables a wired LAN device to join in a wireless LAN environment easily. It also supports enterprise security which allows you to use the Wireless Bridge BR-300AN reliably even in environments such as offices and healthcare sites which require security. This product is not available in North America.
-
Product
Loop Antennas
-
A loop antenna is a radio antenna consisting of a loop or coil of wire, tubing, or other electrical conductor, that for transmitting is usually fed by a balanced power source or for receiving feeds a balanced load.
-
Product
SM / Expansion Unit
-
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
-
Product
PXI Switch - 24-CH 2-Wire Multiplexer Module
PXI-7921
Matrix Switch Module
ADLINK PXI-7921 is a relay multiplexer which consists of 24 2-wire relays (DPDT, 2 Form C). As a multiplexer, the PXI-7921 provides 48x1 1-wire, 24x1 2-wire and 12x1 4-wire configurations. Users could choose one of the configurations by software. PXI-7921 typically connects one instrument, such as a DMM, a digitizer or a signal source, with many points which need measurement or excitation. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7921, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
Product
ITA, ICon, With Protective Cover
410123101
ITA
The iCon ITAs small width and inboard handle allow for easy side-to-side stackability. The u-shaped cable clamp allows modules to be pre-wired before assembly and offers a maximum cable bundle diameter of 1.21". The slide-off cover allows easy access to wiring for maintenance and probing.
-
Product
Cable Assembly 15-Pin D-Type, Female to Female, 2m
40-970-015-2m-FF
Cable Assembly
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products.
-
Product
Power Supplies
CM Series
-
The CM-300 is perfect for those with smaller computer cases – tiny in size, but huge in effectiveness with an anti-corrosive nickel plated chassis. Within this power supply is an 80mm silent cooling fan designed to cool at maximum efficiency with the lowest noise level. And to power your CPU, the CM-300 comes with an 8 pin Xeon connector ready in a tube-tide design to keep all your wires tidy. The CM-300 is the ideal combination of power efficiency in a sleek body kit.
-
Product
8-Pin Power D-Type Cable, Female to Unterminated, Ferrules
A008PF4-F-5A050
Cable Assembly
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
Product
Split type AC Current Sensor
CTF-50A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of terminal feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
Product
Analogue ELCB Tester
1810 EL
-
Standard Electric Works Co., Ltd
● Taut Band movement.● Simple operation.● Wiring check.● Robust.● Can be used on 2 wires L-E (ELCB/RCCB/GFCI tester).● Can be used on 3 wires L-E-N (with wiring check).● No battery required.● Sense automatically 50 or 60 Hz.● Current injected in phase with the voltage.● Other voltage optional (110V).
-
Product
Stud Sensors
-
Stud Sensors such as the MSV100 and MSV350D comprise a category of their own. Each uses electromagnetic induction to sense the presence of (and thereby locate) a stud, pipe, batten, current-carrying wire or other metallic object behind a wall or above a ceiling. The two instruments differ in their choice of the display technology (LED or LCD) used to pinpoint position.
-
Product
PXI-4065, 6½-Digit, ±300 V PXI Digital Multimeter
780011-01
Digital Multimeter
6½-Digit, ±300 V PXI Digital Multimeter—The PXI‑4065 is a 6½‑digit, 300 V DMM, which makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m HV, Exit Away From Pin 1
A050DM4-T-HA050
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Unterminated, Tinned Ends, 2m
A025CFR-T-5A200
Cable Assembly
This 2m long female 25-Pin Micro-D to unterminated (with tinned ends) cable assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connector to its associated product.
-
Product
20-Pin Scorpion Cable, Female to Unterminated, Tinned Ends, 30A, 0.5m
A020AFR-T-3A050
Cable Assembly
This is a 0.5m long female to unterminated 20-Pin Scorpion cable assembly with tinned ends constructed from 37/0.4 (10AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
Wire Crimp Pull Tester (Motorized)
WT3-201M
-
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Product
Cable Assy 78-Pin D-Type F/F 2m
40-970-078-2m-FF
Cable Assembly
A 78-Pin D-Type cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 78-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Low-Temperature Impact Device
DWC-1
-
This low-temperature impact device is compliance with standard requirement of IEC60245, IEC60227, IEC60540, GB5013-2008, GB5023-2008 and GBT2951-2008. It’s used to test all kinds of PVC sheathed cable, wire, soft wire and no sheath of parallel soft PVC insulated impact resistance at low temperature. Specification: • Working temperature: -15℃±1℃ • Impact height: 10~200mm adjustable • Length of specimen: 5D~150D • Material: 304 stainless steel • Completion time once: 3~5s • Completion number of units for once: ≥2pcs • Weight: 100/200/300/400/500/600/750/1000/1250/1500g • Low temperature box to match additionally
-
Product
Test Sockets
-
Yamaichi Electronics Co., Ltd.
A test socket is the ideal point to test your home’s internal phone wiring for faults. You can also use it to identify any potential faults with the phone line outside. Your test socket is located in your master socket. It is the point between the internal phone wiring in your house and the phone line outside. That means by plugging into your test socket you can bypass all the internal wiring and test your device directly on the phone line.
-
Product
AC Power Sources
BPS Series
-
AMETEK Programmable Power, Inc.
The BPS Series consists of multiple high power AC power systems that provide controlled AC output for ATE and product test applications. This high power AC test system covers a wide spectrum of AC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the BPS Series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the unit to its designated location (using included casters), plug it in, and the BPS Series is ready to work for you.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Female, 2m, 45º
A1604F5-1604F5-0A200
Cable Assembly
For applications where a 45 degree cable exit would be preferred. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connectors to have a second fixing then the connector can be fitted with the optional screwlock assembly 40-969-101 where applications permit.
-
Product
Time Domain Reflectometer (TDR) Card
PCI-3127
-
The PCI-3127 is a PCMCIA-form factor TDR that can be used to identify and locate failures in installed wiring and cable systems. The instrument can make high resolution TDR measurements on circuits up to 96,000 feet (~30km) from your Windows XP notebook computer or PC using a low-voltage non-destructive test signal.
-
Product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
Amplifier
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
Product
Flexible Multisensor Probes
IT Series
-
Physitemp multisensors are made with our specially manufactured thermocouple wire. We test and grade this wire to standards better than the accepted ''Special Limits of Error'' and guarantee 0.1°C accuracy in the range of 0-50°C . All multisensor probes conform to NIST standards. These multisensor probes are custom-made and should be ordered to your requirements on number of sensors and spacing between sensors.
-
Product
Solid State Active Synchro Control Differential Transmitter
-
Computer Conversions Corporation
The input is transformer isolated and accuracy applies over the operating temperature range and with +/-10% input amplitude and frequency variations. The operational amplifier outputs are not transformer isolated, and can be driven into external power amplifiers and Scott "T" transformers for 3 wire synchro outputs. A typical application of this series is in a conventional positioning servo system as a complex error processor. The use of the solid state CDX makes possible the design of servo systems that can be digitally programmed by direct computer input to the digital input of the SCDX.
-
Product
Fixed Gas Detectors
OLCT 10 - OLC 10
-
Teledyne Gas & Flame Detection
The OLC 10 and OLCT 10 are designed to detect combustible or toxic gases for tertiary applications (boiler plants, battery charging rooms, car parks, hospitals). Two OLC 10's can be connected to one detection channel to monitor the same area, without an additional junction box or extra wiring. Similarly, up to five OLCT 10's can be connected to one channel for the detection of CO, NO or NO₂ in a car park application. Easy to install and operate, these detectors combined with the MX 16 control unit meet demanding user requirements.
-
Product
Mobile Communications DC Source, 15V, 3A
66311B
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66311B mobile communications DC source provides fast transient, exceptional sourcing, and precision measurement.
-
Product
Gateway
CODA-4682
-
Hitron Americas Technologies Inc.
The CODA-4682 has the capability to receive 5Gbps based on 2 x OFDM + 32 QAM over its DOCSIS 3.1 interface. The integrated Wi-Fi 3×3 2.4 GHz 802.11n and 4×4 5 GHz 802.11ac Wave 2 dual band MU-MIMO Access Point significantly improves customer experience extending range and coverage with blazing speeds. For wired clients, the four Gigabit Ethernet ports offer ultra-fast connections. MoCA 2.0 bonding provides a near-Gigabit wired backbone in the customer’s home for Wi-Fi extension. Its switchable upstream (5~42/5~85MHz) offers the possibility of flexible integration to existing networks.
