Product

Temperature Wire Sensors

-

Omega Engineering, Inc

Omega Engineering, Inc

Temperature Wire Sensors

Product

Digital Low Resistance Tester

TH2512

-

Shenzhen Chuangxin Instruments Co., Ltd.

TH2512 - Shenzhen Chuangxin Instruments Co., Ltd.

The TH2512 series digital dc low resistance tester i s an intelligent, wide range, high-precision tester which suitable for transformer, inductor copper resistance, relay contact resistance, switches, connectors, wire resistance, contact resistance component solder contact resistance, PCB line, welding hole resistance and metal detection, etc. It’s applied to the production line and can use HANDLER interface and GPIB interface (option) output good/bad signal, in order to improve production line automation testing capability.

Product

Telephone Wire Cable Tester For Testing Continuity With Sender And Receiver

PHCT55

-

Pyle Audio Inc.

PHCT55 - Pyle Audio Inc.

The PHCT55 is a two-piece item that tests telephone wire continuity. Play a test tone on one end and listen on the other, judge continuity, and diagnose break points.

Product

U Type Glow Wire Loop

IEC60695-2-10

-

Shenzhen Chuangxin Instruments Co., Ltd.

IEC60695-2-10 - Shenzhen Chuangxin Instruments Co., Ltd.

Thermo resistance, spare part set of Glow Wire Apparatus Acc IEC60695-2-10. Thermo resistance loop is a wire loop that is defined at a temperature and is pressed against a stan­dardized test platelet made of plastic (or other materials) for a prescribed period of time under precise test condi­tions.

Product

80-1000V AC Non-Contact Voltage Tester

5226

-

Peaceful Thriving Enterprise Co Ltd

5226 - Peaceful Thriving Enterprise Co Ltd

This non-contact voltage tester, can be used to test the presence of AC voltage from 80V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.

Product

LXI WTB Adaptor, Thru line

60-982-001

-

Pickering Interfaces Inc.

60-982-001 - Pickering Interfaces Inc.

The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.

Product

Test Contactor/Probe Head

xWave

-

Cohu, Inc.

xWave - Cohu, Inc.

Highest performance and most robust RF broadband production solution for package, wafer, or Over-the-Air (OTA) test for 100 GHz.The xWave™ test contactor / probe head utilizes patented hybrid contacting technology to optimize RF performance and provide robustness for production testing of the most challenging cmWave and mmWave devices. Inside the xWave test contactor / probe head are embedded patch antennas and coplanar waveguides for both wireless and wired communication.

Product

RF/Microwave Assembly Capability

-

Teledyne Defense Electronics

Teledyne Defense Electronics

Teledyne Labtech offers a comprehensive build-to-print microwave module and microwave components manufacturing service. This includes MMIC placement, Au wire bonding, SMT assembly and test.Our microwave MIC production facility is housed in a class 10,000 clean room that accommodates manual chip placement and semi-automatic wire bond assembly. Dedicated microwave components manufacturing is undertaken within production cells established to meet specific customer or product requirements.

Product

Thermometer, -20°C to +400°C, 7.9 ", 2.7 ", 1.2 "

72-6700

-

Tenma

72-6700 - Tenma

Infrared Thermometer*Three thermometers in one...Infrared, Pt100 ohm and Thermocouple*Accommodates 4 wire Pt-100 ohm probes and thermocouple types K, J, R, T, and E.*Selectable readings °C or °F*Data Hold function*Min./Max memory function*Laser guide for IR function*RS 232 output*Auto power off

Product

Multi-Modular Cable Tester

3PK-NT005N

-

Prokit's Industries Co., Ltd.

3PK-NT005N - Prokit's Industries Co., Ltd.

Multi-modular cable tester is applied to quickly test by auto scanning most of modular cable, USOC 4 / USOC6 / USOC 8 terminating with RJ 45, RJ12, and RJ11 modular plug, wires continuity and miss-wiring.It can be also used for testing the cable is crossed pinning or straight through. Moreover, with the remote terminator, it can be further used in remote testing even the cable has been already installed.

Product

SoundLink Underwater Acoustic Modems

-

LinkQuest Inc.

LinkQuest Inc.

With the innovative technologies, LinkQuest's modems have achieved significantly increased data rate (up to 38,400 baud), lower power consumption and unprecedented robustness. All of LinkQuest's modems perform at a bit error rate of less than 10 which is equivalent to the quality of wire line communication. LinkQuest's extensive line of underwater acoustic modems outperform any competing products in technical aspects for both near-vertical, horizontal and extreme horizontal underwater environments.

Product

Measuring Microscopes, Image Processing + Drawing Die And Wire Measurement

Easy Low Cost Wire Drawing Die Measuring Microscope

-

Optik Elektronik Gerätetechnik GmbH

Easy Low Cost Wire Drawing Die Measuring Microscope - Optik Elektronik Gerätetechnik GmbH

Simple optical measuring system for diameter and ovality of wire drawing dies with image processing software.

Product

ABex Terminal Module for Göpel 1149Cx BSCAN Cards

ABex TM-1149Cx

-

Konrad Technologies GmbH

ABex TM-1149Cx - Konrad Technologies GmbH

The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.

Product

Primary Test Equipment

LET-2000-RDM

-

EUROSMC, S.A.

LET-2000-RDM - EUROSMC, S.A.

It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.

Product

Jerking Tester

JLD-10

-

Shanghai Dean Electrical Co., Ltd

JLD-10 - Shanghai Dean Electrical Co., Ltd

Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard:JB/T4279.5-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.000mm and below;Built-in small ultra-quiet air compressor would provide power supply and automatic constant pressure;Samples, while being jerked, would not move and slip out;

Product

H+W (Pylon) 1280 Point Test Interface

-

HW Test

HW Test

H+W (Pylon) 1280 Point Test SystemUp to eight positions for 160 Point Wiring Blocks.

Product

12-600V AC Adjustable Non-Contact Wire Tracer

5221

-

Peaceful Thriving Enterprise Co Ltd

5221 - Peaceful Thriving Enterprise Co Ltd

This non-contact voltage tester, can be used to test the presence of AC voltage from 12V~600V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.

Product

Electrical Insulation Tester Kit with Dual Display

420001

-

Sper Scientific

420001 - Sper Scientific

When undertaking power installations, the 420001-insulation tester can provide special help to test wiring. This unit can provide 125V,250V, 500V and 1000V source for the test, and under each range it can supply 1mA current to feed the capacitance load. With the auto-range function, it can measure up to 4,000 Megaohm with the resolution of 1Kohm.

Product

Industrial Temperature Sensors

-

AMETEK Sensors, Test & Calibration

AMETEK Sensors, Test & Calibration

Temperature measurement and calibration is our specialty, allowing us to provide much more than just standard sensors and assemblies. Our long experience, developing and producing industrial temperature sensors, provides us with a wide knowledge about applications and customer needs. This enables us to build and deliver quick and custom-designed quality temperature sensors for almost any kind of solutions and applications, no matter what industry. We offer a complete range of thermocouple assemblies and resistance thermometers, as well as thermocouple wire, extension wire, temperature transmitters and accessories.

Product

Furnaces

-

Instron

Instron

These three zone resistance wire wound furnaces are of split construction to facilitate fast and easy loading of a pre-assembled specimen train. The case is constructed from stainless steel with aluminium and hardened insulation board end plates. The optional front cut-out allows the use of side-entry high-temperature extensometry. Adjustable stainless steel latches keep the furnace halves locked together during use, but are then easily opened once testing is complete. The furnace is available with optional heavy duty brackets or mountings, which attach to a wide range of testing systems. An extensive range of standard controllers is available to suit most test regimes. Custom variants can be specified should the standard range not include a suitable unit.