ITA
Interface Test Adapter; Interface Connector Adapter: Interface Device
See Also: Interface Test Adapters, Modules, Receivers
-
product
Mini Pneumatic, Contact, ITA, Push-in Fitting, for 4 mm OD Tubing
610132111
Primary mating contact 610131111.Please note: This contact cannot be used to fully populate any compatible VPC module. The larger head size prevents directly adjacent placement.
-
product
Micro Power, Contact, Receiver, 21 Amp, PCB Mount
610142102
Primary mating contact 610143101. (May mate with other ITA contacts, as well.)Specifications Operating Current 21 amps continuousContact Resistance 1.5 mOhms max.Dielectric Withstanding Voltage (DWV) 1500 VDC min.Contact Body BrassContact Plating 30µ" Au over 100µ" NiCycle Life 10,000 cyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 1.23
-
product
Signal / Mini Power/ Mini Coax, Module, ITA, TriPaddle, iCon Series, 64/8 Position
510161103
Primary mating module 510160103. (May mate with other Receiver modules, as well.)
-
product
ITA, 9025, 25 Module, EMI, with 8" Enclosure
410104304
This 9025 ITA comes with an 8" enclosure for ease of system integration. The ITA is designed to work with the 9025 EMI receiver.
-
product
Mini Coax, Module, Receiver, 90 Series, 19 Positions, for use with right-angle contact (p/n 610104160)
510104319
Use with right-angle mini coax contact (p/n 610104160) for mounting to PCBs. Includes holes for PCB mounting.Primary mating module 510108111. (May mate with other ITA modules, as well.)
-
product
Receiver, 9075, 75 Module, Triple Tier
310104307
The 75 Module Receiver has the highest I/O mass interface available. All three tiers accommodate discrete wiring for any application. This Receiver also accepts the standard 9025, 9050 and 9075 ITAs.
-
product
ID, CASS, 19 Module, Single Tier, Commercial
410113105
ID, CASS, 19 Module, Single Tier, Commercial.
-
product
ITA, G2, 2 Module, Removable Backshell, Keying Feature, With Protective Cover
410120110
The G2 ITA is equipped with a removable EMI-shielded cover. The cover slides up to provide access to wires and connectors and is secured by two screws. The removable and adjustable U-shaped cable clamp is attached by screws to the ITA frame and allows ITA modules to be pre-wired before assembly. The clamp can hold cable bundles with an oblong bushing effective diameter of 1.55". ITA strain relief plates are not needed.
-
product
Digital Signal Processing
Digital signal processing routines can be conducted on raw signal data acquired by GaGe high-speed digitizers either directly on the onboard FPGA of the digitizer card via our eXpert FPGA firmware features or can be optionally conducted on GPU cards receiving real-time streaming of raw signal data acquired by GaGe high-speed digitizers via the PCIe interface.
-
product
Signal, Module, ID, CASS, QuadraPaddle, 800 Position
510114131
Signal, Module, ID, CASS, QuadraPaddle, 800 Position.Mating module is 510113138.
-
product
9025TR - 25 Module Solution with Platform
The 9025TR has over twice the I/O as the G12 and is outfitted with the same 20-inch platform to support enclosures while engaging and disengaging. The front-mount ITA is user-friendly, allowing the enclosure or fixture to be fastened from the mating side. The docking feature of the 9025TR provides an easy way of guiding a fixture into position prior to engagement. Runners along the platform provide a smooth-sliding action, ideal when using fixtures up to 180 pounds. The 9025TR uses all standard modules and contacts, includes a microswitch and is available with optional table legs and keyboard tray kit.
-
product
Coax, Patchcord, ITA, 72", Micro Coax, RG178, Single Ended
7-363178000-072
Coax, Patchcord, ITA, 72", Micro Coax, RG178, Single Ended.
-
product
ITA, iCon, Extended Cable Clamp
410123115
This iCon ITA includes an extended cable clamp to accommodate larger cable bundles. The maximum cable bundle area = 1.97 " sq. or a 1.58"/40.13mm diameter bundle. The clamp may be inverted for smaller cable bundles.Please note: This ITA does not offer an increased bend radius that may occur with a larger cable bundle radius. Larger bend radius is offered by the iCon XL, p/n 410123232.
-
product
Enclosure, 50 Module, L-Shaped
410112770
The L-Shaped Enclosure provides significant area for external I/O devices. It features three access panels (front, top and bottom) with removable covers that use 1/4 turn fasteners. The housing is painted black and the access panel covers are black anodized. This enclosure is designed for a 9050VXI ITA, and with the use of adapter plates, can be used with 9050 and 9025 ITA's.
-
product
Signal, Contact, ITA, QuadraPaddle, Male PCB Pin
610138123
Signal, Contact, ITA, QuadraPaddle, Male PCB Pin.
-
product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position
510150115
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
product
Signal, Contact, ITA, TriPaddle, Round Post, PCB Mount
610110000
Primary mating contact 610110179. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAAVG Mating Force(lbs) 0.41Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 Cycles
-
product
Signal, Module, ITA, QuadraPaddle, 90 Series, 480 Position, Unloaded
510151106
NOTE: Part # 510151106 Rev E and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150116. (May mate with other Receiver modules, as well.)
-
product
RJ45 (Ethernet 100 Base T) to 90 Series Interface
J90RJ45I
RJ45 Ethernet connector for VPC Tripaddle ITA moduleUp to 3 connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
-
product
Protective Cover, G20, 6.75" Series Adapters, ITA
410112797
Protective Cover, G20, 6.75" Series Adapters, ITA
-
product
Custom PCB Enclosures
Our customers have shared a long history of using printed circuit boards (PCB) in the interchangeable test adapters (ITAs) of their automated test equipment (ATE) stations. Whether you are designing a self-test fixture and want to save space, improve signal integrity, and/or reduce cable management headaches, VPC has a team of engineers with the expertise needed to help.
-
product
ITA 192-Pin PCB Adapter to 3x IDC 64
YAV90Q06
3x 2 IDC 64 x 1000mmCables set J6200560 (Order Separately)
-
product
ID, CASS, 19 Module, Single Tier, Extended
410113111
ID, CASS, 19 Module, Single Tier, Extended.
-
product
Receiver, ICon, Reverse Module Configuration For ICon ITA Modules, With Protective Cover
310123103
Receiver, iCon, Reverse Module Configuration for iCon ITA Modules, with Protective Cover
-
product
Mini Fiber Optic, Patchcord, ITA, 36", Multimode, 62.5/125, to ST
7-415804506-036
Mini Fiber Optic, Patchcord, ITA, 36", Multimode, 62.5/125, to ST.
-
product
Signal / Mini Power/ Mini Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/8 Position
510160102
Primary mating module 510161102. (May mate with other ITA modules, as well.)
-
product
Signal, Module, Receiver, QuadraPaddle, iCon Series, 160 Position, loaded w/ Twin Female Contacts and Round Posts
510160122
Fully Loaded with Twin Female Contacts and Round Posts (Adapter Pins) (p/n's 610138200 and 610138117).Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
product
LabVIEW Tools for Digital Filter Design and Implementation
LabVIEW Digital Filter Design Toolkit
The LabVIEW Digital Filter Design Toolkit extends LabVIEW with functions and interactive tools for the design, analysis, and implementation of digital filters. New digital filter users can explore classical designs with the built-in interactive design tools, while experienced users can find a breadth of algorithms, filter topologies, and analysis tools for both fixed- and floating-point digital filters. For fixed-point filters, you can model quantization effects, optimize numeric representation/topology, and deploy the design on a digital signal processor or FPGA using automatically generated ANSI C or LabVIEW FPGA code.
-
product
Digital to LVDT Converters
ST-DLVA
Computer Conversions Corporation
The SLVT Series are complete, low profile, continuously updating, single channel, Isolated Digital to LVDT Converters used to simulate the output of LVDT's (Linear velocity displacement transducers), RVDT's (Rotary...) and other phase/voltage sensitive AC devices.
-
product
Mini Fiber Optic, Patchcord, ITA, 36", Multimode ,62.5/125, Single Ended
7-415804000-036
Mini Fiber Optic, Patchcord, ITA, 36", Multimode ,62.5/125, Single Ended
