V.35
-
product
V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF
SBL- 5037533550-1515-E1
50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.
-
product
Automated Meter Test Boards
WECO 4050X, 4150X and 4330X
WECO Electric Meter Test Boards have set the standard at electric utility meter shops and meter manufacturers across North America for over 35 years. The WECO 4000X Series raises that standard once again.
-
product
Acquisition Of Strain Gauges, Isolated, 18-bit
APCI-3300-4
4 channels for the acquisition of strain gauges. 4 onboard voltage sources. 18-bit resolution. Optical isolation 1000 V. Software linearisation. Direct connection of the pressure sensors with terminal board PX3200
-
product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-912
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Test Contactor/Probe Head
cBoa
cBoa™ test contactors and probe heads are the solutions for contacting high-frequency devices for package test or final test at wafer. The robust design and materials of the cBoa probe withstand the rigors of high-volume test by providing longer life and higher yield. The homogeneous DUT side plunger provides longer run times between cleaning and increased probe life.The cBoa features a stainless-steel spring for tri-temp testing and performs in operating temperatures of -55°C to +155°C and bandwidth of up to 35 GHz @ -1 dB.
-
product
Serial I/O Boards
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
product
DC/DC Converter 2 W
REM2-3.305S
DC/DC converter 2 W from Recom | input ranges 3 - 3.6 VDC | output 5 V | operates in ambient temperature from -40 to +95 °C
-
product
Advanced Power System - DC Power Supply, 20 V, 50 A, 1000 W
N6951A
When designing high performance ATE systems, there's an art to the tradeoffs you make when asked to "integrate fast and test faster within budget." That's why Keysight's N6900 Series DC power supplies are small, flexible and market-leading fast. And with our VersaPower architecture, you can tune the N6900 for the optimum balance of test coverage, quality and time.
-
product
AC/DC Power Supply 25 W
CFM25S360-T
AC/DC power supply with 25 W from Cincon | input ranges 90 - 264 VAC | output 36 V | operates in temperature from -30 to +70 °C | class II | wafer version
-
product
Digital I/O
With digital I/O cards, static or dynamic bit patterns can be generated or recorded. Each bit is assigned a control signal for an output and a sensor signal for an input. The usual voltage range for the inputs and outputs is between 2 V (TTL) and 24 V (automation).
-
product
Capacitor Charging Power Supplies
Excelitas Capacitor Chargers are tailored to meet your exact needs by configuring modular platforms based on proven designs. Single-phase AC input designs are capable of up to 6 kW of output power and our three-phase designs provide up to 35 kW of output power. A modular design approach results in lower cost, higher reliability, and faster time-to-market. Typical applications for capacitor charging power supplies include flashlamp pumped laser systems (Nd: YAG, pulsed lasers, dye lasers, Intense Pulsed Light Systems (IPL) and aesthetic Medical Laser Systems, Medical Holmium YAG Laser), excimer lasers, pulsed UV curing and sterilization, radar and RF systems.
-
product
Automatic Measurement
Mylab V
For performing automatic measured simply and easily scenario tabular to make with software such as Microsoft Excel, Mairabo V is the instrument control tool regardless of manufacturer.
-
product
Belt-Pack Transmitter
SMQV
To meet the demand for both extended operating range and extended battery life, the "V" series SM transmitters offer selectable output power (See specific model data sheets for details). A third selection at 50 mW is provided for some theatrical applications where the system design specifies lower transmitter power.
-
product
USB-6525, 16-Channel, 60 V, 8 Solid-State Relays, 8 Inputs, Ch-to-Ch Isolated Digital I/O Device
779640-01
The USB-6525 is an industrial, bus-powered USB I/O device that can automate even the most demanding applications. The solid-state relay outputs are ideal for controlling pumps, valves, motors, and various other industrial actuators. The USB-6525 features channel-to-channel isolated digital inputs that you can use to read from industrial digital sensors, and eight solid-state relay outputs featuring 60 VDC/30 Vrms switching voltage and 500 mA per channel maximum switching current. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators.
-
product
Portable Stroboscopes
Monarch Instrument has been manufacturing Stroboscopes for visual inspection and speed measurement for over 35 years. We are recognized as the leading manufacturer of portable hand held stroboscopes. We have xenon flash tube and LED versions available in a variety of different models to suit your application requirements.
-
product
sbRIO-9425, Non-Enclosed, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
783950-01
Non-Enclosed, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The sbRIO‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The sbRIO‑9425 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
product
16 Relay Output Board, 8 Isolated Digital Input Channels, 24V
APCI-2200-16-8
16 electromechanical relays with change-over contacts ? Max. switching voltage for the relays: 60 V/DC, 48 V/AC ? Max. switching current: 1 A ? Short response time ? Option: 8 input channels for AC voltage, optically isolated, input voltage range: 12 - 24 V DC ? Watchdog: software-programmable release, stop and time selection.
-
product
Datalogging Light Meter (RS-232)
DLM 536
Spectrum of photo sensor meets C.I.E. photopic curve V(l). 16000 Records Data logging capacity. RS-232 interface (software included). Measurement of luminous intensity(PC Software)
-
product
Quadrature Position & Rate Meter
Accepts low-level differential or single-ended 5 V logic level quadrature signals from shaft encoders to display scaled position or scaled rate. One, two or four transitions may be counted at a maximum combined rate of 250 kHz and be mathematically scaled to display in engineering units from -999,999 to +999,999. An analog output scaled to the display and relay outputs are optional.
-
product
Photometric Radiometric Transmitters
HD2021T6 / HD2021T7
The transmitters allow converting the photometric quantity “equivalent veiling luminance” – HD2021T7 – or a photometric quantity Luminance (cd/m2) – HD2021T6 – into a current (4…20 mA) or a voltage (0…10 V) signal according to the version chosen. If the acquisition station is far from the probe (>50m), it is necessary to use the current output version.The probe is used for the control of street lighting, in particular, the measurement of equivalent veiling luminance is essential to determine the threshold luminance at the entrance of the tunnels (UNI 11095:2011).
-
product
Handheld Water Quality Meters
LAQUA WQ-330-K
Triple channel. Large colour graphic LCD screen (70 x 52 mm) with backlight. Built-in foldable meter stand. IP67 waterproof and dustproof. Battery and USB powered. Eco-friendly, shock-proof, scratch-resistant, and non-slip. Built-in sensor holders. Efficient sensor locking mechanism. Sensor's LED light as reading stability indicator. No sensor adapter needed for attaching multiple sensors together. Compatible with conventional electrodes having BNC and phono connectors and long cables. Sensor status indicator. Temperature sensor indicator. °C & °F temperature units. Sample ID setting. Detailed calibration data. Auto stable, Auto hold, and Real time measurement modes. Customizable meter kit - up to 35 meter-sensor kit combinations. Hands-free testing. Ergonomic design. Multi-language options. Versatile channel and adaptive display. Up to 3 simultaneous calibrations and measurements. Automatic sensor recognition function. Data transfer via USB or wireless communication. Printer communication. 3 years meter warranty.
-
product
Non-Contact Voltage Testers
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-02
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers
-
product
Advanced Power System: Dynamic DC Power Supply, 120 V, 16.7 A, 2000 W
N7976A
The N7976A is designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
product
Cryocooler
CryoTel® DS30
The CryoTel® DS 30 Stirling cryocooler offers efficient, reliable, compact and high power cooling to the market in the temperature range of 35 to 250 Kelvin. The DS30 was optimized for applications in which SWAP (size, weight and power) and reliability are concerns. The DS30 consumes considerably less power than other cooling alternatives and requires no maintenance, making it ideal for strategic as well as industrial applications. Both the cold head and the pressure wave generator can be mounted in any orientation. Application examples include semiconductor manufacturing, large infrared detectors, RF receivers or antennas, astronomical telescopes, laser cooling, high-temperature superconductivity, cold traps, and others.
-
product
DC/DC Converter 60 W
XRCM60-12DQF
DC/DC converter with 60 W from Bel Power Solutions | input ranges 16.8 - 137.5 VDC | output 12 V | operates in temperatures from -40 to +70 °C | provides 20 ms hold up time | O-ring FETs and built-in fuse
-
product
Potentiostat Galvanostat
EchemLab XM
EchemLab XM includes a reference grade potentiostat and frequency response analyzer (FRA). EchemLab XM has a built-in 100 V high voltage amplifier which can be used for not only for compliance measurements but also for high voltage cell polarization. This is useful in many high solution resistance applications, for example in organic electrochemistry. In addition to high voltage, power boosters can also be integrated to combine high current and high voltage in many specialized plating applications.
-
product
Basic AC Power Source, 2000 VA, 310 V, 10 A
AC6803B
This basic AC power source offers stable, reliable power up to 2000 VA. An intuitive user interface and flexible I/O connectivity.Increase your uptime with stable, reliable AC power source.Engineer reliability into your designs with a basic AC power sourceTest your designs with confidence.Test under real-world conditions - fluctuating voltage or transient spikes.Easily access setup and measurement information.
-
product
Electrostatic Meter
STS 1
The electrostatic sensor STS 1 is a compact electrostatic meter with a digital display for measuring static charges in the range of positive and negative numbers easily and precisely. The wide range of measurement, the high accuracy, the reduced drift and a resolution of up to 1 V make the electrostatic sensor STS 1 an all-rounder for all fields of electrostatic measurements.
-
product
Regenerative Power System 1000 V, ±90 A, 30 KW, 400/480 VAC
RP7982A
The RP7982A regenerative power system is a single output, bi-directional, regenerative DC power supply with safety features to protect your people and your DUT.
