Magnetic
attraction; of opposite polarity objects, magnets to ferrous materials and themselves.
See Also: Force, Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic Test, Magnetic Field, Magnetic Head, Magnetic Susceptibility, Magnetic Flux, Magnetic Stripe, Magnetic Permeability, H-field, Core Loss
-
product
The Lightest Micro-ohmmeter In The Industry
RMO-H
The RMO-H is a portable, battery-operated micro-ohmmeter based on state-of-the-art technology, using the most advanced battery mode and switching technique available today. The high-capacity Li-Po battery allows the generation of a ripple-free DC current of up to 300 A. The test current is user-selectable and generated in an automatically regulated test ramp. During the test, the RMO-H increases the current before the measurement and decreases it afterwards. This significantly reduces magnetic transients.
-
product
Hall probes
Axial, transverse, multi-axis, and tangential Hall probes for measuring magnetic flux density. Choose from a wide range of lengths and thicknesses—probes are also available for cryogenic applications.
-
product
Free DR and High Field Magnet in Shared Vacuum Space
50 mm 4 K magnet bore, 30 mm sample space in DRSuitable for use with Leiden DR type CF200, CF450, CF650 or CF1000 DR
-
product
Hall Effect Speed Sensors
SPECTEC Innovative Sensor Solutions
SPECTEC zero speed Hall effect gear tooth sensors are used in industrial applications to determine shaft or gear speed or direction by detecting fluctuations in the magnetic field. The Hall effect technology fulfills a wide array of applications due to a Hall effect sensor's ability to detect zero speed and the quadrature sensor's ability to detect direction change. The Hall effect gear tooth sensor's digital output is easily read by computers, motion control devices, position monitors and digital to analog converters. Intrinsically Safe zero speed sensors are available for various applications.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Coating Thickness Meter for Ferrous and Non-Ferrous Materials
CM8826FN
- Operating principle: magnetic induction/eddy current (F/NF)- Measuring range:0-1250um/0-50mil- Resolution; 0.1/1- Accuracy: 鍗?-3%n or 鍗?.5um- Min. measuring area: 6mm- Min. sample thickness: 0.3mm- Battery indicator: low battery indicator- Metric/ imperial: convertible- Power supply: 4x1.5V AAA(UM-4)battery- Auto power off- Operating conditions:0-+45閳?/span>(32閳?/span>-104閳?/span>),閳?0%RH- Dimensions: 126x65x27mm- weight: 81g(not including battery)- Optional accessories: other range 0-200um to 15000um
-
product
EMI Test System
EMI-9KA
EMI-9KA is an automatic EMI receiver. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KA is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem. The test results are according to the international format test report. The EMI Test System EMI-9KA fully meets CISPRl6-1, GB17743, FCC, EN55015 and EN55022.
-
product
Electromagnetic
Promis 10
The Promis device is a multi-frequency, multi-spacing 3 component slingram type EM System for sounding and profiling the soil. This system features a transmitter loop to produce a primary magnetic field that will induce eddy current in conductive materials. These eddy currents will generate a secondary magnetic field that will be measured with the receiver loop. This system measures the in-phase and the out-of-phase components of the secondary magnetic field.
-
product
Magnet Analyzer
Since miniaturization and high accuracy is the most important theme in the motor industry, a progression in the field of magnetizing ripple analysis is demanded. Taking advantage of our spindle motor design experiences, we develop and manufacture many magnet analyzers with high accuracy, functionality, and operability. We also produce a magnet analyzer which fulfills each customer's needs.
-
product
Scanning Probe Microscopy/Atomic Force Microscopy (SPM/AFM Analysis)
Rocky Mountain Laboratories, Inc.
Scanning probe microscopy (SPM) refers to a family of measurement techniques that utilize a scanning probe. The most common measurement is Atomic Force Microscopy (AFM Analysis), which measures surface topography. Imaged areas can be from the nm scale to as large as 100 µm X 100 µm. Heights and depths of features can be measuredand many surface roughness parameters, e.g Ra, can be calculated. 3-D images can also be produced for dramatic data presentation. Magnetic and electrical response can also be measured with SPM.
-
product
SparkFun Breakout
HMC6343
The HMC6343 is a fully integrated high end electronic compass module that can compute and give you a heading direction that’s accurate within a couple degrees. It is tilt compensated and is calibrated to handle magnetic distortions. This breakout board allows for easy use of the HMC6343. All that is required is power and I2C connections to a microcontroller so that the module can receive commands and send data back to the user.
-
product
Rotary Encoders
Absolute encoders
Optionally with magnetic or optical scanning technology, in many different designs, quick and easy to integrate. Baumer always has the right absolute encoder for you - whether traditional point-to-point or high-performance Ethernet interfaces.
-
product
Superconducting Magnet Power Supply
A true 4-quadrant, low noise, stable superconducting magnet power supply. Ideal for small to medium-sized superconducting magnets.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
product
TEM Cells
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
product
Capacitance Sensors
Accumeasure Series
The Accumeasure product line features capacitive sensor products for high resolution gap and displacement measurements that require a high level of accuracy that is both stable and repeatable. A capacitive sensing system consists of a probe and amplifier. Capacitive measurements can be performed in a multitude of environments using non-contact passive capacitance probes that are not affected by magnet fields, temperature, humidity, nuclear radiation, and pressure. This is largely due to the nature of the rugged and passive capacitance probes.
-
product
E-Field Generators
TDK E-Field Generators - generate controlled, high-intensity electric and magnetic fields over the frequency range of 10kHz to 100 MHz
-
product
Contactors
Mitsubishi Electric Automation, Inc
Compact dimensions, modular expansion options and a power-saving design are the key characteristics of the MS-N and MS-T series magnetic contactors. DIN rail mountable and standardized terminal covers make installation and wiring user friendly and cost effective.
-
product
Low-Noise Fluxgate Sensor
FL1-100
Fluxgate magnetic field sensor with sub-nanotesla resolution and exceptionally low noise. Suitable for detection of fine metal parts in food, measurement of magnetic signatures, paleomagnetic applications, precision navigation, surveillance, shielding technology, and more.
-
product
Dewpoint Meter
319
A hand-held dewpoint meter with both manual and automatic data logging in one gaugeIntegrated magnets allow the dew point gauge to be attached to the substrate during remote loggingStores 25,000 records in up to 999 batchesDustproof and waterproof gauge with fully sealed sensors (equivalent to IP66)Gauges can be recertified at Elcometer Authorised Service CentresRobust temperature sensorsEasy to use, intuitive menu structureMeasure and record climatic parameters:Relative humidityAir temperatureSurface temperatureDewpoint temperatureTΔ (the difference between surface temperature and dewpoint)Dry Bulb temperatureWet Bulb temperatureExternal temperature correction (K-type)Specific HumidityVisual and audible indication of user defined limits for any or all parametersUSB and Bluetooth® data output to ElcoMaster® software
-
product
Magnetic Core Selector
UI9702
• Measure relative value of μm, Bs, Br, Hc integrated factor• No need of wiring, direct testing, being convenient• Automatic selecting, out of limit alarming, freely setting of the selecting limit• Driving current for test: 0-2A, frequency for test: 20-50kHz, both continuously adjustable, Comply with actual working situation of electronic ballast• No need of adjusting the instrument every day• Digital display, easy to read, simply and quickly to operate• Print B-H curve
-
product
Complete Overview Of Magnetic Field Measuring Devices Teslameter Gaussmeter
The field strength measuring instruments are ideally suited for measuring magnetic field strength but also for residual magnetism (remanece)andetermination after demagnetization of metals.
-
product
MM-Wave Sources From 36 To 178 GHz Based On BWO
Insight Product Company offers a BWO based MM-wave sources of radiation at frequencies from 36 Ghz to 178 Ghz. Each source includes millimeter-wave BWO tube and a specially designed permanent magnet system. BWO tube is installed inside the permanent magnet and does not require any adjustment by the customer. Offered sources are the most wide-banded, they are very reliable, small sized, powerful and easy to operate.
-
product
Radiating Loops
The magnetic, handheld coil was designed to generate defined mag-netic fieldstrength in the frequency range from DC up to 5 (7) MHz. The main application is immunity testing against magnetic fields.
-
product
Industrial Gaussmeter
The industrial gaussmeter IGM11 is used to measure magnetic DC and AC fields. The measurands are flux density in Tesla or Gauss and the field strength in Amps per meter.
-
product
Speed Switch
M100T/M5000T
Features• Internal sensor• SPDT relay output• 5-100 rpm (M100T), 100-5,000 rpm (M5000T)• Terminal block for easy wiring• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Works with Electro-Sensors magnetic pulser discs/wraps• Explosion proof (XP) housing• UL Listed Class I, Div I (C, D) Class II (E, F, G)
-
product
EMC Probes
The Beehive Electronics 100 series EMC probes allow the accurate measurement of magnetic and electric fields. They are useful for EMC troubleshooting, field strength measurement, and troubleshooting of RF circuits.
-
product
Magnetic Pole Indicator
identification of the field-direction of a magnet (north - south). It simply ascertains, fast and reliably the polarity of permanent magnets and electromagnets. This reliable device is simply to be served. It is indispensable for all industrial areas and fields of investigation which deal with magnetic applications.
-
product
Small/Medium Capacity Type High-Speed Rotation Torque Detector
TH-2000/1000 Series
The TH-1000 series torque detectors employ a new magnetic phase difference method with improving functionality while maintaining the advantages of Ono Sokki's conventional torque detectors. They incorporate high durability and long service life---the biggest features of our torque detectors. The new magnetic phase difference method does not require AC power supply to an auxiliary motor for rotation detection change. TH-1000 series is a standard type torque detector with the rotation speed range up to 6000 r/min. The TH-2000 series is a high-speed rotation type which can be used for torque characteristic test of high-speed rotating motor such as an EV/HEV motor, a centrifuge machine or the like. The characteristic data of the detector can be automatically set up on the TH-5100 torque meter when power is turned on.
-
product
Calibration & Demag.
Model 8515-D
The Model 8515-D is a medium-energy, high voltage, and capacitor discharge type ringing demagnetizer capable of desaturating Ceramic and Rare Earth magnetic materials. The Model 8515-D is easily adapted to a wide range of production and laboratory demagnetizing requirements. A modern solid-state electronic control circuit, coupled with a rugged, heavy-duty discharge SCR and fixture, make this demagnetizer a highly reliable, low maintenance unit. The electronic voltage control circuit prevents the Model 8515-D from being discharged before the preset energy level has been reached, avoiding incomplete magnet desaturation. An easy to read front panel meter monitors the capacitor voltage. The energy storage level can be easily changed in the field. Integral electrical interlock and fail-safe circuitry provide a high degree of operator safety.
