Product

Testing Aircraft Tachometers

-

Magtrol Inc.

Magtrol Inc.

The test bench is comprised of a TMB 304 Torque Transducer and a custom fixture for the tachometer and corresponding inertia wheel. A servo motor is incorporated to provide speed to the tachometer. The entire drive train is conveniently mounted on a base plate with the appropriate couplings, bearing support and flywheel.

Product

VXI Module

VDSP-31

-

ALPHI Technology Corporation

VDSP-31 - ALPHI Technology Corporation

The VDSP31 is a VXI based, multi-channel data acquisition system and digital servo control module. The VDSP31 offers a complete solution for high performance closed loop applications. The VDSP31 has been designed to solve specific problems related to the control of hydraulic actuators. Signal conditioning modules can be combined on a per channel basis to configure the VDSP31 for load or displacement feedback.

Product

Solid State Synchro Control Transformer and Solid State Resolver Control Transformer

SCT-RCT Series

-

Computer Conversions Corporation

SCT-RCT Series - Computer Conversions Corporation

The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems. They simultaneously accept a 3 wire synchro input (0) and a digital angle input (0), and provide an ouput which is the sine of the difference between these two input angles (A sin wt sin (0-0) ("wt" is the synchro excitation frequency).

Product

Energy-Conservation Unit For Servopulser Hydraulic Power Supply Unit

ECU1/ECU2 Series

-

Shimadzu Corp.

ECU1/ECU2 Series - Shimadzu Corp.

Up to 50 % energy savings. Contributes to reduced CO2 emissions and lower running costs. The conventional hydraulic power supply unit for fatigue and endurance tests is always driven at full power to achieve the maximum test force and maximum velocity and the hydraulic power supply unit is selected in order to satisfy the maximum test performance. Therefore, depending on the test conditions, energy is excessively consumed. With the ECU Series the motor rotational speed and the supply pressure of the hydraulic power supply unit can be set in multiple stages, so energy savings of up to about 50% can be achieved depending on the test conditions and test circumstances. It is used in combination with the Servo Controller 4830. (The Servo Controller 4830 is provided separately.) * Appearance and specifications are subject to change without notice.

Product

Closed-Loop Servohydraulic Test Bench Control System

-

ZETLAB Company

ZETLAB Company

Closed-loop servohydraulic test bench control system is based on digital devices of ZETSENSOR series with CAN interface. This system has fast response characteristics, high precision, and compact dimensions. The system enables comprehensive control of the servo drive in automated mode in compliance with the set test parameters such as pressure (force), displacement, along with the parallel control of other system parameters such as temperature, pressure, filter plugging, oil pressure, etc.

Product

STPOWER SLLIMM Intelligent Modules

-

STMicroelectronics

STMicroelectronics

Nowadays, the market requires high-performance solutions able to satisfy the increasing energy-saving requirements, compactness, reliability and system costs in home appliances and in low-/medium-power motor drive applications as well as in HVAC, servo motors and other high-power industrial drives.

Product

Servopulser Table-Top Fatigue And Endurance Testing Machine

EHF-L Series

-

Shimadzu Corp.

EHF-L Series - Shimadzu Corp.

This revolutionary fully digital servo controlled multi-functional materials testing machine opens up a new era in fatigue testing systems. It provides excellence in all aspects, including precision, reliability, and expandability, through its fully digital control achieved by bringing together the latest technologies.

Product

Brushless/Servo/Stepper Motor Tester

-

Shanghai Aoboor Electric Co., Ltd.

Shanghai Aoboor Electric Co., Ltd.

Applicable to brusheless, servo,stepper motor performance test.

Product

Coordinate Measuring Machines

-

Dongguan Kejian Instrument Co., Ltd.

Dongguan Kejian Instrument Co., Ltd.

Standard series full automatic vision measurement machine is with Full CNC close-loop axis motion control, servo motors and joystick, ensures stable and fast movement, increase the measuring accuracy and efficiency. Also the package solution for the control system offers stable performance of the machine, minimizing the maintenance.

Product

Automatic Vision Measuring Machine

-

Sinowon Innovation Metrology Manufacture Ltd.

Sinowon Innovation Metrology Manufacture Ltd.

Moving bridge structure, measured workpiece is fixed;◆ Four-axis CNC fully auto close loop control, auto measurement;◆ “00” grade “JINANQING”marble base and pillar, stable and reliable;◆ Imported open type linear scale, resolution is 0.1um, high accuracy, great stability;◆ Imported P grade linear guide, precision grinding ball screw and AC servo motor, ensure accuracy stability of system position;◆ Imported high definition color industry camera, ensure clear observation and stable measurement requirement;◆ 6.5X continue auto zoom lens, precision auto zoom, only need to make pixel calibration once time;◆ Programmable 5-ring 8-division LED surface illumination, contour parallel LED illumination, can realize 256 grade brightness adjustment intelligently;◆ Equipped with imported touch probe, realize 3D measurement;◆ With proprietary fully auto measuring software iMeasuring 4.2, powerful function, simple operation;◆ Optional laser probe, it can also be customized according to customer request;◆ Optional FexQMS Measuring Data Analysis and Real-time monitoring software which enhance program control and reduce material

Product

Dynamic and Satatic Electro-Hydraulic Servo Testing Machine

PLS Series

-

Jinan Testing Equipment IE Corporation

PLS Series - Jinan Testing Equipment IE Corporation

PLS series dynamic and static testing machine is produced according to the dynamic servo test technology. Our design of the electro--hydraulic servo testing system is unitized, standardized and modularized, which enhance the stability and reliability of the system. The electro-hydraulic servo testing system is mainly used to test the dynamic and static mechanical performance of material parts. Equipped with corresponding accessories, the servo-hydraulic testing system can do tensile, compression, low and high cycles, crack growth tests and other mechanical tests for various kinds of materials. The Dynamic and Static Testing Machine is widely used in the fields of aviation and aerospace, ship-building and military industries.

Product

Precision Linear Actuators

ECT-Series

-

Thomson

ECT-Series - Thomson

Thomson's ECT Series of Precision Linear Actuators are our highest performing line of electric cylinder systems. Designed for the most demanding applications, the ECT Series is ideal when powerful performance over a long life cycle is required. With a full complement of drive controls, accessories, options, and mounting types, these systems are adaptable to just about any application environment. As a better choice over hydraulic or pneumatic equivalents, the ECT Series are simpler to install, maintain, and control. This family comes in two different sizes mating our traditional Movotrak T90 and T130 actuators with both AC servo and 3 AC induction motor configurations.

Product

Servopulser Vibration Testing Machine

EHV Series

-

Shimadzu Corp.

EHV Series - Shimadzu Corp.

This machine performs vibration tests on structures, equipment, transport packages, etc. Vibration directions include horizontal and vertical. Large capacity and large stroke can be obtained with the electro-hydraulic servo system.

Product

Integrated Laser Controller + Servo

SILC

-

AOSense

SILC - AOSense

Discover our integrated laser controller with servo which has all the features of the standard ILC with additional servo features.

Product

Automated Programmer Superpro Sb05

-

Xeltek

Xeltek

※ Four Pick & Place nozzles, Eight socket pressing actuators and 2 tape feeders※ High throughput up to 2400UPH※ Embeded with eight ultra-high speed programmers SuperPro / 7500, each with up to 4 sockets, totally 32 sockets. Throughput 60 times higher than SuperPro / SB01 for eMMC devices※ Supports over 80,000 devices from over 300 IC manufacturers※ Supports tray, tape and tube input and output. Supports laser and ink marking※ Short change-over time※ Intelligent s/w cuts learning curve and setup time, makes task management an easy job※ Compact sizeHigh throughput：4 nozzles, 8 independent socket pressing actuators and 2 tape feeders. Up to 2400 UPH for devices with programming time less than 50 sec. Throughput 0.6 to 60 times higher than SuperPro/SB01, especially higher for large capacity devices like eMMC, NAND /NOR FLASH,SPI FLASH. Suitable for both small and large capacity devices. Prog. Time (S) 50 60 120 180 240 300 UPH (unit per hours) 1600 1600 840 560 420 336 Accurate positioning：Equipped with high performance servo system, precise CCD cameras and vision algorithm for device alignment and sockets / pick & place spots positioning.High performance programmers： 8 ultra-high speed universal gang programmers SuperPro/7500 resident. Each with up to 4 sockets, totally up to 32 sockets in the system. Supports up to 100,000 devices from over 300 IC manufacturers and growing.Varied I/O devices：Supports tray, tape and tube input and output. Supports laser and ink marking. Supports packing conversion and can work as a packing conversion machine alone.Short change-over time：I/O devices and socket adaptor are easy to be changed when programming task need to be changed. Socket positioning can be performed automatically. Projects can be loaded automatically with barcode scanning.Powerful and intelligent software：Setup data saved for next operation, log file and statistic reports for quality and yield traceability, flexible sockets prohibition strategy promises high yield rate for unattended operation, graphical user interface cuts learning curve, prevents chip over-lapping by socket checking before chip placing.Remote Control：Remote project loading, quality monitoring, volume control, file security.

Product

EtherCAT Master Multi-Axis Motion Controllers

DMC-52xx0

-

Galil Motion Control, Inc.

DMC-52xx0 - Galil Motion Control, Inc.

The DMC-52xx0 EtherCAT Master is Galil Motion Control's first 32 axis motion controller. It is a pure EtherCAT controller capable of controlling up to 32 drives and 2 IO modules on one EtherCAT Network in a small, space efficient package. The DMC-52xx0 makes configuration and programming easy with just a handful of EtherCAT configuration commands and Galil’s intuitive, two-letter programming language. The DMC-52xx0 is offered in 2, 4, 8, 16, and 32 axis formats. Coordinated moves can be done within banks of 8 allowing for minimal changes to Galil’s programming language. Galil supports a variety of EtherCAT drives to accommodate most applications. The DMC-52xx0 operates in Cyclic Synchronous Position mode (CSP). In this mode the servo control loop is closed on the EtherCAT drive while the Galil sends motion profile data at a 1 kHz rate. The DMC-52xx0 features 8 uncommitted opto-isolated inputs and 8 uncommitted opto-isolated high power outputs. It also includes 8 uncommitted analog inputs and 8 uncommitted analog outputs. One 100 Mbps Ethernet port and one USB (serial) port are provided for communication with a host PC or external devices.

Product

Solid State Active Synchro Control transformer and Solid State Resolver Control Transformer

-

Computer Conversions Corporation

Computer Conversions Corporation

The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems. They simultaneously accept a 3 wire synchro input (0) and a digital angle input (0), and provide an ouput which is the sine of the difference between these two input angles (A sin wt sin (0-0) ("wt" is the synchro excitation frequency).

Product

Servo

-

Unitronics Group

Unitronics Group

The Hardware: Drives, Motors, Cables (standard and robotics) – all seamlessly supported by Unitronics’ PLCs, HMIs, & VFDsThe Software:One integrated software for your complete motion application: PLC, HMI, Servo, VFD, and I/O

Product

PWM Amplifiers

SA Series

-

Motion Control Systems, Inc.

SA Series - Motion Control Systems, Inc.

Covering a power range of 5 to 20 KVA, the MCS line of high frequency PWM servo amplifiers utilizes the latest in solid state power circuitry and power devices to provide the greatest amount of flexibility available in the brushless motor drive market. The SA Series is a stand alone system with integral power supply designed for industrial application where the system will mount inside a NEMA type enclosure.

Product

Precision Positioning stage

N-661

-

Physik Instrumente GmbH & Co. KG

N-661 - Physik Instrumente GmbH & Co. KG

Miniature Linear Stage with NEXACT Drive Travel Range 20 mm Self Locking at Rest, no Heat Generation, no Servo Dither Compact Design: 70 x 50 x 20 mm Zero-Wear Piezo Stepping Drive, Ideal for Micro- and Nano-Manipulation Integrated Linear Encoder Option for Highest Accuracy with 20 nm Resolution Two Operating Modes: Continuous Stepping Mode and Continuously Variable, High-Dynamics Analog Mode for 30 pm Resolution** Up to 10 N Force Generation

Product

Inspection System

Pixie

-

Ginolis Ltd.

Pixie - Ginolis Ltd.

3-D Metrology for automation. Pixie is a standard system for automated optical quality inspection. Pixie can be configured with 2 to 5 servo driven axis movement and the high-speed measurement capabilities make it suitable for inline and stand-alone solutions.

Product

Advanced Telemetry System

HTS-SS

-

Hitec RCD USA

HTS-SS - Hitec RCD USA

Our HTS-SS Advance telemetry sensor station works compatibly with all our existing sensors as well as the HTS-ETEMP, HTS-AS, HTS-VM and HTS-SM.  Delivering on its name, the HTS-SS Advance provides more advanced telemetry capabilities than any other RC telemetry system and is capable of monitoring all types of models.  It also provides engine temperature via the HTS-ETEMP sensor, air speed via the HTS-AS sensor, sensitive rate-of- climb tracking via the HTS-VM sensor and servo performance via the HTS-SM sensor. This leading-edge telemetry module provides the most reliable and comprehensive communication with your model yet. Expect More! Expect Hitec!

Product

Transmitter (Export Only)

SMDB

-

Lectrosonics, Inc.

SMDB - Lectrosonics, Inc.

The input section features the unique servo bias input circuitry with a standard TA5M type jack for use with electret lavaliere mics, dynamic mics, or line level signals. A DSP-controlled analog audio limiter is employed before the A-D converter. The limiter has a range of more than 30 dB for excellent overload protection and a dual release envelope that makes the limiter acoustically transparent while maintaining low distortion. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels to keep audio distortion low while preserving short term dynamics.

Product

MCB Tripping Current Characteristic Test Bench

-

SCR ELEKTRONIKS PVT. LTD.

SCR ELEKTRONIKS PVT. LTD.

The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.