PMC Adapters
Computer boards that translate the data from the PMC bus to another bus and vice versa. They are used to connect two incompatible buses. (globalspec.com)
-
Product
Pull-Thru Adapter, Wired, for Pickering 40-161-101
510140177
Pull-Thru Adapter
Pull-Thru Adapter, Wired, for Pickering 40-161-101
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, To NI PXI-2529
510150148
PCB Adapter
This PCB Adapter was designed specifically for the NI PXI-2529, which uses 160 signals at 2 amps. This PCB Adapter will accommodate one or two NI TB-2634 terminal blocks. If 192 signals or 3 amps are needed for a different application; use # 510 150 155 which has 6 32-pin ribbon cable connectors capable of up to 3 amps each.
-
Product
Attenuator Interconnect Kit, 2.92 mm
11716D
Interconnect Adapter
The 11716D attenuator interconnection kit provides the necessary parts to connect 84904L and 84906L programmable step attenuators in series.
-
Product
Adapter, 1.0 mm (f) to 1.85 mm (m), DC to 67 GHz
11921H
Coax Adapter
The Keysight 11921H precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2 x 68-Pin FML VHDCI
510150126-1
PCB Adapter
Single PCB adapter p/n 510150126 ships with 2 x 68-pin VHDCI male double-ended 2m cables, packaged separately. Available PXI card solutions for NI PXI-2535 and PXIe-7868.
-
Product
Coax, Contact, ITA, 20/26 GHz, 3.5MM, w/ SMA Adapter, 90 Series Modules only
610102134
Contact Adapter (ITA)
Coax, Contact, ITA, 20/26 GHz, 3.5MM, with SMA Adapter (90 Series modules only)
-
Product
Pull-Thru Adapter, Wired, TriPaddle, f/ NI PXIe-5423
510140249
Pull-Thru Adapter
Pull-Thru Adapter, Wired, TriPaddle, f/ NI PXIe-5423.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (f), 40 to 60 GHz
U281A
Coax Adapter
The Keysight U281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Coax, Contact, Receiver and ITA, 40 GHz
610102114
Contact Adapter (Receiver/ITA)
The 40 GHz Coax contact is a blind mate connector that mates with 3.5 mm and 2.92 mm connectors. It is recommended to use 2.92 mm connectors for frequencies above 35 GHz.
-
Product
Threaded Coupling Adapter, G2, G6, G10, ITA, For Conduit Harnessing Assemblies/Clamps
410112599
Coupling Adapter
The Adapter is designed to accommodate military and commercial circular backshells for conduit or strain relief when designing for general and heavy-duty applications. The male thread size is 1.625-18 for this application.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2529 with six 20" cables
510150153
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2529 with six 20" cables
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female DIN
510140141-2
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female DIN
-
Product
Pull-Thru Adapter, Wired, TriPaddle/Mini Coax, 90 Series, for PXIe-5172
510140248
Pull-Thru Adapter
Pull-Thru Adapter, Wired, TriPaddle/Mini Coax, 90 Series, for PXIe-5172.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, For NI PXI-6509
510140138-1
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, for NI PXI-6509
-
Product
NI-6584, 16 Mbit/s, 32-Channel Digital I/O Adapter Module for FlexRIO
781290-01
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter
-
Product
PXI Module Adapter, Pull Thru Adapter, Receiver, 1 Position
510109462
Adapter Module
PXI Module Adapter, Pull Thru Adapter, Receiver, 1 Position.
-
Product
PMC to PCI Adapter / Carrier
PMC2PCI
-
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.
-
Product
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs
510140111
Pull-Thru Adapter
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs.
-
Product
Adapter Plate, Allows 10 Module ITA To Accept 25 Module Enclosure
410112424
Adapter Plate
The Adapter Plate allows the user to use standard 25 module enclosures with the 10 module ITA. See enclosures in the 25 Module section for more options.
-
Product
PCB Adapter, ITA, VTAC, to (2) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) and (4) RJ45 Connectors
510171114
PCB Adapter
Mates with p/n 510170114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
Product
Test Port Adapter Set, 3.5 Mm (Test Port) To Type-N
85130C
Test Port Adapter
The Keysight 85130C test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to type-N male adapter and a 3.5 mm to type-N female adapter. The frequency range for these adapters is dc to 18 GHz with a return loss of 28 dB or better.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-139-101
510140254
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-139-101.
-
Product
Adapter, 2.4 mm (f) to 3.5 mm (f), DC to 26.5 GHz
11901B
Coax Adapter
The Keysight 11901B is a 2.4 mm female to 3.5 mm female, metrology-grade adapter with dc to 26.5 GHz operation.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, PXI 160 Pin DIN
510140311
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, PXI 160 Pin DIN
-
Product
Adapter Plate, 9050 Enclosure to 9025 ITA
410112772
Adapter Plate
Adapter Plate, 9050 Enclosure to 9025 ITA (ITA Positioned on Upper Part of L-Shaped Enclosure)
-
Product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
Test Port Adapter
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2x68 Male SCSI Connectors
510150125
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Male SCSI Connectors
-
Product
Test Port Adapter Set, 1.85 Mm To 1.85 Mm
85130H
Test Port Adapter
The Keysight 85130H test port adapter protects the test set port from being directly connected to the device under test. This adapter has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 1.85 mm to 1.85 mm male adapter and a 1.85 mm to 1.85 mm female adapter. The frequency range for these adapters is dc to 67 GHz with a return loss of 23 dB or better.
-
Product
Adapter, 2.4 mm (m) to 3.5 mm (f), DC to 26.5 GHz
11901C
Coax Adapter
The Keysight 11901C is a metrology grade, 2.4 mm male to 3.5 mm female adapter with dc to 26.5 GHz operation.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (f), 50 to 75 GHz
V281C
Coax Adapter
The Keysight V281C is a 1-mm female to V-band waveguide adapter with a frequency range of 50 GHz to 75 GHz. The V281C is used with the Keysight 8510XF systems.
