-
Product
50 Pin SGMC Connectors for Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize the 50-pin SGMC connector.
-
Product
Automotive Back Probe Pins
142-5
-
Flexible 1.5 inch silicon pins provide easy back probing connections for DMM and Scope measurements
-
Product
BNC (M) To Stacking Pin Tip Plugs
3901
-
BNC (m) to stacking pin tip plugs. Miniature banana plug springs are gold plated Beryllium Copper for excellent electrical connection.
-
Product
Extractor Tool for MS-M RF connector pin
40-969-501-ET
Extraction Tool
Extractor tool for RG178 co-axial pins fitted into MS-M connector housing.
-
Product
Single Pin Horizontal EFS
-
Teledyne DGO offers an advanced, high-reliability subsea wellhead single channel electrical feedthrough system for use in intelligent completions with permanent downhole instrumentation. The connection system is designed for long-term reliability in the demanding subsea and downhole environments with sour well (H2S) conditions, as well as aggressive production and packer fluids.
-
Product
9 Pin D-Type Connector, Male
92-960-009-M
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed when using this product.
-
Product
High Density 68 pin
HDEterm68
-
The high density 68 pin SCSI II/III connector is being used for purposes other than SCSI interfaces because of board and front panel space limitations. For example in the PMC environment the SCSI connector provides an excellent size and pin count for the front panel space allowed. The SCSI connector while dense, is not easy to connect to with wiring intended to go to multiple locations
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
25 Pin 1.27mm Pitch Micro-D Connectors
-
The connectors below are suitable for high-density applications including Pickering’s LXI DIO/Trigger port.
-
Product
44 Pin D-Type Connectors For Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a 44-pin D-type connector.
-
Product
Trailer Buddy 4/5 Pin One Man Trailer Wiring Tester
220
-
*Tests 4 & 5 Pin Flat connector wiring *Each signal from vehicle emits a unique tone *Loud beep can be heard over shop noise *One person makes complete test in 30 seconds! *Just apply brakes, turn signals, running lights& engage reverse *Tester also emits unique tone for any shorts in the wiring! *Greatly reduces time spent verifying vehicle trailer wiring *Very simple & easy to use - saves time!
-
Product
2 Meter Long SCSI Cable with 100 Pin Connector
U2904A
Digital Cable
The Keysight U2904A is an accessory compatible and recommended to be used with the U2600A Series USB used with the U2600A USB Modular Digital I/O modules. The pin-outs of the U2904A is dependent on the USB Modular Digital I/O module that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2903A is to be used with.
-
Product
Additional Products: 160 Pin DIN 41612 Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
PIN Diodes
-
PIN photodiodes convert light to current – without a bias voltage having to be applied. Silicon is commonly used as an inexpensive detector material in the Vis range. For higher demands, InGaAs is used; it covers the widest spectral range from the Vis to the NIR. We offer silicon carbide as a “solar-blind” detector specifically for the UV range.
-
Product
SP2T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
Product
20 Pin GMCT Cables - Connector to Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 20-pin GMCT connector
-
Product
25 Pin D-Type Connectors For Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a 25-pin D-type connector.
-
Product
SP6T RF Pin Diode Switches To 12 GHz
-
The SP6T series of 6-way absorptive and reflective switches manufactured by Pulsar Microwave cover applications from 300 MHz to 12 GHz. They have an isolation of 60 decibels and most models specify 1.6:1 or better return loss throughout frequency band. These 6-way switches require a +/- 5VDC supply to operate. Switching control uses individual 0-5V TTL control logic. Voltage and logic control interfaces into a system using a 9-pin D-SUB connector installed.
-
Product
Cable Assembly, Receiver, 36", TriPaddle, 68 Pin ML VHDCI
540120030201
Cable Assembly
Cable Assembly, Receiver, 36", TriPaddle, 68 Pin ML VHDCI.
-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
37-Pin D-Type Male Solder Pin HV
92-960-037-MHV
D-Sub Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
Pin Type Moisture Meter
2022
-
Peaceful Thriving Enterprise Co Ltd
The moisture meter measure the moisture by the conductivity between the two pins. It can be widely apply for fiber material, for example, building and its construction material, various nonmetallic material, paper, wood, bamboo products, herb, tobacco, cotton, textile, soil and so on. Easy operation, clear indication; LCD screen will display the moisture of the target.
-
Product
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 18"
515109119
Cable Assembly
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 18"
-
Product
SP3T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures 3-way absorptive and reflective switches for use in 50-ohm systems. These SP3T switches operate from 100 MHz to 18 GHz and handle 200 mW input power. VSWR performance is often 1.6:1 or better with 100 ns switching time. Minimum isolation of 60 dB is specified for most units. Absorptive and reflective switches require +5V and -5V power supply to function. Control logic is from 0 to +5 volts. All voltage and ground connections are made by feed thru and turret terminals, respectively.
-
Product
68 Pin 1.27mm Pitch Micro-D Cables - 68 Pin to Alternative Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 68-pin micro-D connector.
-
Product
Additional Products: 8 Pin Power D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Adapters & Pin Converters
-
Need to adapt your emulator's JTAG connection? We have a variety of pin converters to help connect your debug probe to your target board's JTAG connection, such as TI, MIPI, ARM, and Cortex.
-
Product
MICROWAVE SILICON LIMITER PIN DIODES
-
Insight Product Company offers Microwave Silicon Limiter PIN Diodes with p+-i-n+ structures are designed to be used in microwave protective  devices included in hybrid integrated circuit (HIC) hermetically sealed, design of which provides protection against  moisture, salt, fog, mycelial fungus, hoarfrost, dew, decreased and increased pressure.
-
Product
6 Round Pin Trailer Circuit Tester
PT7897
-
Tests trailer circuits on most light/medium duty trucks and campers.Traces each lighting function to the terminal in question.
-
Product
68 Pin 1.27mm Pitch Micro-D Connector & Cable Accessories
-
The 68 Pin 1.27mm Pitch Micro-D Connector is used on high-density PXI modules that require 1A current rating and voltage handling up to 150Vdc.
