High Frequency
High Frequency operating at 3–30 MHz.
-
Product
Dual Channel Digital Receiver
MS 1740
-
Dual Channel Digital Receiver is a complete high−frequency dual−channel A/D converter capable of sampling rates up to 210 MHz. It accepts two front panel analog inputs and delivers digital output samples over four FPDP (Front Panel Data Port) connectors utilizing FPDP standards. The Dual Channel Digital Receiver features two 12−bit Analog Devices AD9430 A/D Converters, and two user−configurable Xilinx® Virtex−IV Series FPGAs. It also features a VME A64/D64 slave interface for setting up operating modes and selectable A/D range, and optionally provides 32−bit access from the VMEbus to the FPGAs. It is an ideal system as a high−speed data acquisition front end for real time recording and digital signal processing systems.
-
Product
Mini Receiver
FB7-NX
-
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
Product
Login Digital Epstein Tester Model
Model EP400
-
Digital Epstein Tester EP-400 is designed to measure AC magnetic properties of flat rolled magnetic materials at high frequency by using Watt-meter, Ammeter, Voltmeter and Source. Epstein bridge test method is a fundamental method for evaluating the magnetic performance of flat-rolled magnetic materials in either sheared or stress relief annealed condition. This test method is suitable for design, specification acceptance, service evaluation, and research and development.
-
Product
Super Phosphor Oscilloscopes
SDS2000X-E Series
-
The SDS2000X-E series employs a new generation of SPO technology. With its excellent signal fidelity, background noise is lower than similar products in the industry. It has a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400,000 frames/sec (sequence mode). It also employs a 256-level intensity grading display function and a color temperature display mode not found in other models in this class. Siglent’s newest oscilloscope offering supports multiple powerful triggering modes including serial bus triggering and decoding. History waveform recording and sequential triggering allow for extended waveform records to be captured, stored, and analyzed. Also included is the deep memory FFT. This math function uses upto 1 M samples for the FFT calculation, providing the SDS2000X-E with very high frequency resolution. The hardware co-processor executes true fast measurement and math to all of 28M sample points so that there is minimal distortion on analysis. It also supports searching and navigating, on-screen Bode plot, 16 channel digital /MSO (optional), an external USB powered 25 MHz AWG function generator module (option), a USB WIFI adapter for wireless control and monitoring (option), and an embedded application that allows remote control via web browser. The features and high-performance of the SDS2000X-E oscilloscopes cannot be matched else anywhere at this price.
-
Product
4-Way Power Dividers From 0.5 To 60 GHz
-
Pulsar Microwave's 4-way power dividers are available in narrowband and broadband configurations, covering frequencies from 500 MHz to 60 GHz. They are designed to handle from 10 to 30 watts input power in a 50-ohm transmission system. Microstrip or stripline designs are utilized, and optimized for best performance.Units come standard with SMA or N female connectors, or 2.92mm, 2.40mm, and 1.85mm connectors for high frequency components.
-
Product
Event Based Image Sensors
EVS
-
Event-based Vision Sensors (EVS) help alleviate this issue by only sending data from pixels who have detected a change in intensity. This allows them to minimize the volume of data that is transmitted over the sensor’s data bus while minimizing the processing resources need to analyze the image. On top of this, individual pixel autonomously responds to illuminance changes allowing the sensor to detect small and/or high frequency changes with lower bandwidth requirements.
-
Product
PXI Dual 8 to 1 Mux 2GHz 50Ohm SMB
40-748-511
-
The 40-748 is a dual 8 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-748 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
Product
Products for High-Frequency Measurement
-
This product range includes passive high-frequency test probes and accessories as well as touch-protected BNC plug connectors, insulated BNC panel-mount sockets, leads with RG58 or RG59 cable, adapters and converters. Our test probes are suitable for use in CAT III- and CAT IV environments (Measurement Categories), such as the analysis of house and building installations with mains analysis/mains monitoring devices. Our high-frequency accessories are designed with clearance and creepage distances in accordance with IEC/EN 61010-031.
-
Product
Corona Resistant Tester of Enamelled Wire
DPT-1000S
-
Shanghai Dean Electrical Co., Ltd
·The tester is comply with the requirements of standards GB/T 1707-2008, GB/T 24122-2009, GB14711-2013, meet the requirement of standard JB/T 10930-2010;·Multiple samples can be tested at same time;·Used for testing the feature of high frequency pulse resistance (performance of Corona-resistance).
-
Product
High Frequency LCR Meters up to 30MHz
11050
-
Chroma Systems Solutions, Inc.
The Chroma 11050 Series HF LCR Meter is a precision test instrument designed to accurately measure and evaluate passive components at high speeds. Its measurement capabilities cover the primary and secondary parameters required for testing the inductance, capacitance, resistance, quality factor and loss factor of passive components. The HF LCR Meter has a broad testing frequency range 75kHz~30MHz/1kHz~10 MHz/60Hz~5MHz suitable for analyzing component characteristics under different frequencies. Its 0.1% basic measurement accuracy provides stable and highly reliable results. A fast 7ms measurement speed effectively increases productivity when working in an automated environment.
-
Product
Voltage Meter
MN3I
-
М-module МН3И is a mezzanine module designed to measure the instantaneous voltage value of high-frequency signals via 3 galvanically isolated channels from each other, control circuits and crate frame.
-
Product
Compact Loudspeakers
ULTRA-X40
-
The ULTRA-X40 brings the technology breakthroughs in our flagship LEO Family line arrays to a versatile, compact loudspeaker. Its innovative concentric-driver configuration couples two 8-inch cone drivers to a rotatable waveguide surrounding a 3-inch high-frequency compression driver, to deliver smooth response across its entire range and directional control down to 400 Hz.
-
Product
High Frequency Current Transformer
HFCT Ø 140mm
-
Techimp Clamp High Frequency Current Transformer model 140 is an inductive sensor for partial discharge measurements. It is suitable for online /off line PD tests on : large diameter cables ; grounding rod bar ; etc. A TNC termination is available to connect the Clamp HFCT 140 to the TechImp PD analyzer : PDCheck , PDBase etc. The arrow indicates the requested input current (Iin) direction to get coherent output voltage (Vout) polarity respect to ground. When the sensor is installed with the arrow directed to ground, the detected voltage signal (Vout) has the same phase of the input current (Iin).
-
Product
QDRII/DDRII/ QDRII+/DDRII+ SRAM
-
DDR II / II+ (Double Data Rate) SRAMs and QDR^(TM) II / II+ (Quad Data Rate) SRAMs are the ideal memory devices for next generation networking and communications systems. These ultra-fast devices can support high bandwidth systems that require memories capable of very high operating frequencies combined with low latencies and full cycle utilization.
-
Product
CFL Testing Instruments
-
CFL testing instruments of Lisun Group includes: High Frequency Fluorescent Lamp Test, Adjustable Reference Ballast, Digital Torsion Meter, Multiplex temperature tester, Lamp cap gauge, etc.
-
Product
High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor
GP-X
-
Panasonic Industrial Devices Sales Company of America
The inductive displacement transducers of the GP-X Series use eddy current techniques and are particularly noted for their highly accurate measurement at a resolution of 0.02% F.S. with minimal linearity error, a high sampling frequency of 40kHz and low temperature dependence. GP-X Series Sensors are ideally suitable for the highly accurate motion and distance control of metal objects in harsh industrial environments.
-
Product
Transistor Arrays
-
Renesas' portfolio of transister arrays include NPN, PNP, NPN-PNP combination transistor arrays based on our complementary UHF-1 SOI process. This portfolio also includes ultra high frequency transistor arrays for VHF/UHF amplifiers, VHF/UHF mixers, IF converters, synchronous detectors. Dual long-tailed pair transistor arrays and Gilbert Cell UHF transistor arrays are also available for wireless communication systems, radio and satellite communications and high performance instrumentation.
-
Product
High Impedance Active Probes
34A
-
Engineered to meet the stringent demands of advanced high frequency circuit designers. This high impedance probe combines full DC capability, rise/fall times of 120 ps, and a nominal loading input impedance of 10 megohm shunted by 0.1 pf. Signal attenuation is 20:1 with a 50 ohm oscilloscope input.
-
Product
Differential Probe
DP-100
-
*This is the first detachable design (patent for 15 years)*High frequency, big power using. Max. Measuring is 7000Vp-p.I*t is capable for any brand of digital and analog oscilloscopes.*Additional AC Adaptor.*16MΩ high input impedance.
-
Product
PWM Amplifiers
SA Series
-
Covering a power range of 5 to 20 KVA, the MCS line of high frequency PWM servo amplifiers utilizes the latest in solid state power circuitry and power devices to provide the greatest amount of flexibility available in the brushless motor drive market. The SA Series is a stand alone system with integral power supply designed for industrial application where the system will mount inside a NEMA type enclosure.
-
Product
RF Cable Assemblies
-
Radiall's extensive range of RF cable assemblies features outstanding electrical performance, low loss and high frequency. The range includes flexible, semi-rigid, corrugated and hand-formable cable assemblies with a combination of RF cables and connectors optimized for each market or application. Custom RF cable assemblies are also available.
-
Product
Passive Probe, 10:1, 150 MHz, 1.2 M
N2841A
-
The Keysight N2841A low-cost passive probe provides a 10:1 attenuation and features a high input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.
-
Product
Fan Type Ionizer
ER-F
-
Panasonic Industrial Devices Sales Company of America
With a compact size of 150 x 166 x 62mm and a fan of 120mm in diameter, the ER-F Fan Type Ionizer belongs to the leading class of compact Fan Type Ionizers. The system employs a high-frequency AC method and boasts a +/-2kV discharge output voltage that discharges electrostatic contaminated objects quickly and safely. Louvers for long distance and wide area applications are shipped with the Ionizers. Standard fan types for faster charge removal times and low-volume types for discharging small parts or film are available.
-
Product
Signal Generators
ZTX-Series
-
RPG's Signal Generator Extenders allow high performance frequency extension of microwave sources into the THz range. The available models cover a Frequency Range from 50 GHz up to 1.1 THz. These modules combine high test-port power with low phase noise to offer exceptional performance. Contact RPG to discuss Signal Generator Extenders configurations that will gain the best performance for your application.
-
Product
Amplified Photodetectors
-
Hinds Instruments' photodetector modules are specifically designed for use with high frequency optical signals including those generated in Photoelastic Modulator (PEM) applications.
-
Product
MIPI Camera Serial Interface
CSI
-
Arasan provides a Total MIPI CSI-2 IP Solution supporting two options: MIPI CSI-2 v1.2 for D-PHY physical interface only, and MIPI CSI-2 v1.3 for the new MIPI C-PHY v1.0 and D-PHY v.1.1, v1.2, and a future v2.0. Arasan offers the C-PHY in a combination configuration that supports both C-PHY interfaces and D-PHY interfaces. Our implementation makes efficient use of the high frequency signally pins for a minimal overhead to support both physical interfaces.
-
Product
Charged Plate Monitor
Model 280A
-
Simco-Ion’s Model 280A incorporates enhanced circuitry that enables it to more accurately measure the performance of high frequency AC ionizers, as well as pulsed DC ionizers and steady-state DC ionizers. The Model 280A can be used as a portable CPM and is capable for of up to 6 hours of operation on the internal battery before recharge.
-
Product
MOD MONITOR
TYPE HFX-1
-
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
Product
Occupational Health & Safety RF Meters, High Frequency
-
Occupational Health & Safety RF Meters by Sensory Perspective LLC
-
Product
RF Switch
-
RF switches are components used for switching the signal paths of high frequency circuits in wireless communication devices.
