High Frequency
High Frequency operating at 3–30 MHz.
-
Product
Artificial Power Supply Network
KH3762
-
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
Product
Tri-phase High Power Programmable AC Power Source
APS50000
-
Advanced direct digital frequency sythesizer(DDS) waveform generation technology, high frequency stability, good continutyMeasurement precision is high, suitable for current half-sinusoid and its similar waveforms with DC component measurementProvide embedded intelligent PC monitoring systemAdjustable output voltage from 0 to 150V, 0 to 300V, step distance 0.1VOutput frequency 45-120Hz(40-500Hz optional), step distance 0.1 HzOutput current limiting functionWith 9 sets of memory, you can store commonly used parameters for easy invocation when using themWith RS232C communication interface 【IEEE488.0(GPIB)optional】, instruction execution times is less than 10mSProtechtion mode: over voltage, over current, overload, short circuit,current limit, ectProvide RMS voltage, RMS current, active power, frequency, power factor, ectFor 100% load removal, voltage stabilizing reaction time within 20ms, strong overload capacity, instantaneouscurrent can with stand 3 times of rated current
-
Product
Selective Level Meter
Model SLM620
-
- Digital Synthesized Local Oscillator- Two Selective Bandwidths : 20Hz, 3.1KHz- Wideband, Low Noise and Low Distortion Measurements- dB/dBm Operation- High Frequency Stability- Internal Calibration Facility- Recorder Outputs- Frequency Tracking Facility with Level Oscillator SLG620- Storage of Nine Spot Frequencies- Reference Level Set Facility- Autotune Feature- Operates on AC Mains or Internal Rechargeable Battery- Built in charger- Graphic LCD Display with Backlight
-
Product
DC - 12 GHz High Efficiency GaAs HBT MMIC Divide by 4 Prescaler
HMMC-3024
-
The HMMC-3024 is a DC - 12 GHz divide by four pre scaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
Product
4-Way Power Dividers From 0.5 To 60 GHz
-
Pulsar Microwave's 4-way power dividers are available in narrowband and broadband configurations, covering frequencies from 500 MHz to 60 GHz. They are designed to handle from 10 to 30 watts input power in a 50-ohm transmission system. Microstrip or stripline designs are utilized, and optimized for best performance.Units come standard with SMA or N female connectors, or 2.92mm, 2.40mm, and 1.85mm connectors for high frequency components.
-
Product
Standard 0.80 (22.00) - 4.00 (114.00) High Frequency Probe
CSP-03G-003
High Frequency Probe
Current Rating (Amps): 6Bandwidth @ -1dB (GHz): 3.70Return Loss @ -20dB (GHz): 1.80Nominal Impedance (Ohms): 50Dielectric VTE Rating (k VAC): 1Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Overall Length (mil): 1,090Overall Length (mm): 27.76
-
Product
EMC Testing
-
D.L.S. Electronic Systems, Inc
EMC testing and consulting services to the Electronics, Medical Equipment, Automotive, Aerospace, Computer, Telecommunications, and other industries. We are a NVLAP certified test facility, capable of testing electronic equipment to today's high frequency requirements. Our 14 Test chambers and 3 Open Area Test Sites can perform full scan Immunity and Emission testing at frequencies up to 40 GHz. Please contact us for your specific requirements.
-
Product
Bandwidth-Controlled Seismic Source
eSource
-
Teledyne Bolt, Inc. has engineered a new type of airgun designed to reduce the potential impact of seismic acquisition operations on marine life while also delivering optimal bandwidth for subsurface imaging. eSource is designed to reduce the high-frequency components believed to have most potential for causing disturbance to marine life while retaining the low-frequency components critical to seismic exploration.
-
Product
6 Channel Function Generator / Flow Simulator
DP-cPCI-2601
-
DP-cPCI-2601 is a 6 Channel 2MS/s Waveform Generator with high frequency performance, versatility and compact size in an economical cPCI bus format. Signal output in the range of 10 mHz to 5 KHz with 14 bit vertical resolution makes this single slot, 6U-sized cPCI card a powerful solution to meet most demanding test stimulus.DP-cPCI-2601 uses Direct Digital Synthesis (DDS) technique to generate stable and accurate output waveforms down to 0.01 Hz resolution. DP-cPCI-2601 offers Sine, Square, Ramp, Triangle, Pulse as built-in wave shapes and user defined arbitrary waveform.DP-cPCI-2601 can frequency sweep any of its function outputs. User can sweep upwards using linear sweeps.
-
Product
CFL Testing Instruments
-
CFL testing instruments of Lisun Group includes: High Frequency Fluorescent Lamp Test, Adjustable Reference Ballast, Digital Torsion Meter, Multiplex temperature tester, Lamp cap gauge, etc.
-
Product
Passive Probe, 10:1, 75 MHz, 2-Pack
N2142A
Oscilloscope Probe
The Keysight N2142A is an extremely low-cost passive probe that provides a switchable 10:1 / 1:1 attenuation and up to 75 MHz bandwidth. It features a high input resistance of 10 MΩ (switchable to 1 MΩ) to address a wide range of measurement needs with low probe loading. The probe can be adjusted for both low-frequency compensation and high-frequency compensation. For the best measurements, you should compensate your probe to match its characteristics to the oscilloscope. This probe is compatible with Keysight InfiniiVision Series oscilloscopes with 1 MΩ input.
-
Product
Electrodynamic 3-axis Vibration Tester
-
Our unique technology, "special slide mechanism" and "floating mechanism" enable 3-axis simultaneous vibration test in high frequency band up to 2000 Hz, which was difficult to realize so far. A frequency range up to 2000 Hz is essential for vibration testing Of Aerospace Electronic And Electrical Devices. Conventional Single-Axis Vibration Testing Has Been The Mainstream In Conventional High-Frequency Vibration Testing Machines, But High-Frequency Three-Axis Vibration Testing Is Essential To Ensure High Reliability Of Electronic Components Such As EVs, HEVs, motors, inverters, ECUs and PCUs. By performing a 3-axis simultaneous vibration test, it has become possible to reproduce complex vibration generated in a real environment in the test room.You can also select various environmental tanks. It is possible to select a high performance model with low cross talk and high surface distribution performance and a general model .
-
Product
Compact Transmitter Module
AMC-I
-
Virginia Diodes'' Signal Generator Extension Modules (SGXs) provide high performance frequency extension of microwave signal generators into the THz range. VDI now offers integrated Amplifier / Multiplier Chains that provide industry leading performance in a compact package.
-
Product
Memory
-
Renesas is renowned for its product lifetimes, and our memory products are no different. Our wide range of low power SRAM products provide high reliability, stable supply and long lifetime support often not found in these devices, making them ideal for industrial designs. Renesas’ ultra-fast QDR™ (Quad Data Rate) SRAMs are ideal for next-generation high bandwidth communication systems that require memories capable of very high operating frequencies combined with low latencies and full cycle utilization. Our EEPROM realizes high speed, low power consumption and a high level of reliability by employing advanced MONOS memory technology, a CMOS process and low voltage circuitry technology.
-
Product
Personal RF Detection Meters, High Frequency
-
Personal RF Detection Meters from Sensory Perspective Ltd
-
Product
2.5 GHz, 0.9 pF, 1 MOhm Active Voltage Probe
ZS2500
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS2500 is ideal for 2.5 GHz and lower oscilloscopes.
-
Product
Spectrum Analyzers
SK4M Series
-
*Frequency range: 100 Hz to 20/50 GHz*DANL < −165 dBm/Hz*Low Phase Noise −125 dBc/Hz at 1 GHz signal from 100 kHz offset*High Frequency Reference Accuracy ±0.1 ppm*Resolution Bandwidth Range 1 Hz to 10 MHz*Built-in Low-noise Amplifier
-
Product
950~2600MHz. SAT-IF Direct Modulated Optical Transmitter
HDS-26S
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDS-26S (original model: HDBS-3000TX) series satellite L-Band optical transmitter, adopts high linearity DFB laser and direct modulated way. It can transmit 950~2600MHz L-Band analog or digital satellite signal (SAT-IF) receiving by satellite aerial radio high frequency head, to realize total transparency, high quality, long distance transmission through optical fiber. It also can sue satellite L-Band up/down link.
-
Product
Compact Fan Type Ionizers
ER-Q Series
-
Panasonic Industrial Devices Sales Company of America
With Panasonic’s high-frequency AC method and “Sirocco Fan”, the ER-Q Compact Fan Type Ionizer can remove electrostatic charge even at slow fan speeds.ER-Q Ionizers are extremely compact and well suited for removing localized electrostatic charge on manufacturing equipment for electronics or in Semiconductor processes. The ER-Q Ionizers require no compressed air which eliminates air lines and reduces additional maintenance.
-
Product
4.0 GHz, 0.6 pF, 1 MOhm Active Voltage Probe
ZS4000
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.6 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS4000 is ideal for 2.5 GHz and 4 GHz oscilloscopes.
-
Product
Dual Voltage Buffer with Current Drive
BUF-01
-
The BUF-01 Voltage Buffer is a dual channel buffer capable of driving up to 50 mA of current on each channel at up to ±10 V output. The buffer has a 2nd order low pass filter with 3 dB point of 119 kHz to remove high frequency noise. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues.
-
Product
Advanced 4-Axis Servo & Stepper Motion Controller with Modular Design
PCIe-8154
Motion Controller
The PCIe-8154 delivers high-frequency pulse rates up to 6.55 MHz and hardware-controlled emergency stop, software security protection, card index switching, and simultaneous linear/ circular run, exceeding industrial cost/performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and any pulse-train controlled servo and stepper drives, the PCIe-8154 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous contouring. Applicable for a variety of linear and circular trajectories, the PCIe-8154 delivers the smoothest motion control for a wide range of manufacturing applications. Modularized configuration accommodates ADLINK extension boards for distributed I/O control and high-speed triggering functions.
-
Product
Compact Range for 5G & High Frequency Wireless Communications
-
Wireless devices are moving toward higher frequencies, and 5G is coming soon. With that in mind, we partnered with WavePro to build an ultra-precise, high-frequency compact range (up to 300GHz) with 50% quiet zone efficiency. Customers can now measure an accurate radiation pattern of a laptop with built-in WiGig transmitter within a 1.2m x 1.2m x 2.2m space.
-
Product
Oil Resistivity Test System / Million Meg Ohm Meter (MM1)
OTD-45
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Model : OTD-45OTD-45 is single self contained unit containing oil test cell, high frequency induction heating with temperature controller/sensor; dielectric loss measuring bridge, AC test voltage source, SF6 filled standard capacitor; high resistance meter; DC voltage source and all digital circuits.
-
Product
Very High Frequencies Analyzer
VHF104
-
VHF104 is an innovative Dynamic Mechanical Analyzer that applies a direct experimental method to measure the material viscoelastic properties over a very high frequency range from 100Hz up to 10kHz.
-
Product
MXA Signal Analyzer, 10 Hz To 50 GHz
N9021B
Signal Analyzer
The optimum choice in wireless for 5G and other new-generation devices Evolve test needs of advanced wireless R&D and manufacturing with the widest analysis bandwidth in its class and superior phase noise performance at high frequencies See through the complexity of challenging signals with RTSA and industry-leading PathWave 89600 VSA software Simplify testing with one-button measurements from PathWave X-Series measurement applications Enable faster test time with enhanced frequency sweep algorithm and hardware-based signal processing without compromising RF performance
-
Product
Ultrasonic Flaw Detector
-
Shenzhen Graigar Technology Co.,Ltd.
Flaw detection is the most commonly used technique among all the applications of industrial ultrasonic testing. Generally, sound waves of high frequency are reflected from flaws and generate clear echo patterns.
-
Product
Frequency Expansion Modules
-
bsw TestSystems & Consulting AG
Up To 1.5THz For Network Analyzers Modern communication standards, like for instance 5G, place high demands on components (mixers, amplifiers, antennas, etc.), which have to be examined in high frequency bands (millimeter waves); the requirements include: broad frequency coverage, sufficient output power to operate the components under compression, high dynamic range and stability as well as a reduced dynamic content within the spectrum.
-
Product
PXI Dual 8 to 1 Mux 2GHz 50Ohm SMB
40-748-511
Multiplexer Module
The 40-748 is a dual 8 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-748 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
Product
Isolated ADCs
-
Isolated analog-to-digital converters (ADCs) are second-order sigma-delta modulators that convert analog values into a 1-bit stream and are able to withstand high common-mode voltages.Combining a high-frequency external clock input and wide bandwidth, our isolated ADCs provide very high accuracy thanks to the improved signal-to-noise ratio (SNR). The isolation grade and a high level of transient immunity are keys to reliably sensing currents and voltages to ensure the robustness and high performance of many industrial applications.
