Optic Sensors
Detect and measure light.
-
Product
Optical Gaging Products
-
Quality Vision International Inc.
OGP® pioneered multisensor measurement with vision, touch probe and laser sensors. For over 75 years, OGP has consistently led with a succession of innovative systems and sensors to tackle the most difficult measurement challenges, especially as it pertains to the medical industry. Multisensor metrology is a preferred quality control technology for manufacturers to develop, maintain, and improve the quality of medical devices.
-
Product
Barometer Logger Sensor
NUL-221
-
This logger sensor measures atmospheric barometric pressure and can display data in four common units. kPa kilopascal atm atmospheres in Hg inches of mercury mm Hg millimeters of mercuryThe sensor also offers an option to display the measured pressure values in terms of altitude (in meters).
-
Product
Outdoor AGC Optical Node
SR812B
-
Hangzhou Softel Optic Co., Ltd.
SR812B optical receiver is our new development products that especially used in CATV network. The pre-amp adopts GaAs MMIC amplify module and the post-amp adopts GaAs power doubler amplify module .Support specifical attenuation and equalization inserts if you want.Or as per customer, adopts other module.With optimization design and plentiful technical experience that made this equipment with high performance specification. It is a ideal model for CATV network.
-
Product
Rolling Shutter Image Sensors
-
Rolling Shutter devices start and then stop their exposure line by line. This means that that each line will be recorded at a slightly different exposure time. This effect is pronounced for short exposures which produces images with distortion due to moving objects and short flashes of light.
-
Product
Sensors
-
Omron’s experience in MEMS technology has enabled it to develop advanced micro component sensors ideal for a wide variety of consumer, commercial and industrial applications. Among these component, or micro, sensors are MEMS micro-pressure sensors, micro-tilt sensors, mass flow and velocity/clogged filter sensors. Target applications include medical, HVAC, consumer electronics, networking infrastructure and test equipment.
-
Product
MCCI Catena® 4460 Sensor Wing w/ BME680 VOC Sensor for LoRaWAN™ Technology
-
The MCCI Catena® 4460 Sensor Wing is a flexible open-source IoT device wing designed specifically for use with the Adafruit Feather M0 with LoRa® radio system, but suitable for use with any Adafruit Feather CPU board. Like the Catena 4450, when combined with a suitable CPU, it is a ready-to-use platform for LoRaWAN™ 1.0 and 1.1 wireless IoT applications.
-
Product
Submersible, Waterproof Sensors
-
Linear, rotary and tilt sensors, IP68 sealed for continual submersion to 10 bar (150psi, 100msw depth), 350 bar (5000psi, 3500msw depth). Designed for the marine environment these corrosion resistant sensors offer very long life and high performance.
-
Product
Single Axis AC Magnetic Field Sensor
MGCH-2
-
Macintyre Electronic Design Associa
The MGCH-2 is the lowest noise, highest sensitivity single axis AC magnetic field sensor available for the measurement of sub radio frequency fields. Because of its innovative design, the MGCH-2 amplitude response is insensitive to the frequency of the field over its 10 Hz to 100 kHz frequency band. Accuracy at 10 kHz is 0.1 dB, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
PI/O Optical Transceiver
-
GCI's sensors are the preferred solution for E84 optical communications. GCI's full line of PI/O transceivers are fully compliant and are compatible with other manufacturers' sensors that conform to the SEMI Standard E84. Leading 300mm FABs, OEMs, and EFEM manufacturers choose the GCI sensor for its superior reliability and stability.
-
Product
Optical Tool Kit
TC-406
-
Techwin(China) Industry Co., Ltd
Optical Tool Kit makes ideas happen and makes your work easier.
-
Product
Two-Way Optical Loss Tester
KI23403OLV-INGAAS-APC-50U
-
A Two-Way Optical Loss Tester (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on multimode fiber at 850 / 1330nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. A multimode APC connector on this model is required for reliable ORL test performance.
-
Product
pH Logger Sensor
NUL-206
-
This sensor can be used to measure the static pH values of common liquids (water, milk, soft drinks, vinegar, etc.) as well as the changing values in titrations or experiments such as those looking at the effect of antacids.
-
Product
Inductive Sensors
-
Inductive sensor designed to detect shaft speed, shaft position, gate position, or object presenceTotally sealed constructionMulti-voltage 24 - 240 VAC/VDCDetects ferrous targets up to 5/16" (8 mm)IP 65 Protection
-
Product
USB Sensor Hub
E1736A
USB HUB
Small and light weight, the Keysight E1736A USB Sensor Hub gives users the ability to connect up to four sensors to a PC. Connection from the sensors to the sensor hub is made using interchangeable cables available in 5m, 10m, 15m, and 25m lengths. Connection is made via an easy to snap in connection.
-
Product
Liquid Level Sensors
-
Are used to detect liquid levels or interfaces between liquids such as oil and water or liquids and solids. They can be defined as sensors or transducers, or as integrated systems with instrumentation and control capabilities.
-
Product
Optical Channel Monitors
-
DiCon's Optical Channel Monitor is an advancedoptical subsystem, with integrated tunable optical filter, that automatically scans a DWDM network and reports the power of each channel. Network performance is monitored and reported in real time. Feedback from the Optical Channel Monitor can be used to optimize optical power levels, identify performance drift, and verify system functionality. An optional integrated optical switch allows up to 12 separate input ports to be monitored sequentially.
-
Product
Family of Wavefront Sensors
ShaH
-
The family of fast, accurate and reliable wavefront sensors. High quality lenslet arrays optimized for reducing the subapereture crosstalk. An interface to a variety of CCD and CMOS sensors allows a wide range of acquisition bands from UV to near IR.
-
Product
Optical Connectors
-
Radiall's full range of optical interconnect solutions includes standard interfaces, optical termini, optical connectors and custom optical assemblies and subsystems. Suitable for harsh environments and designed for demanding applications where reliability and high performance are required, our cost-effective optical connectors are adapted to the specific requirements for the telecom, industrial, aerospace and defense markets.
-
Product
Smoke Detection Sensor - CE Approved
ENVIROMUX-SDS-CE
-
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.08-0.14 dB/m. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
Transmissive Optical Encoder Module
EM1
-
The EM1 is a transmissive optical encoder module designed to be an improved replacement for the Avago HEDS-9000 series encoder module. This module is designed to detect rotary or linear position when used together with a code wheel or linear strip. The EM1 consists of a lensed LED source and a monolithic detector IC enclosed in a small polymer package. The EM1 uses phased array detector technology to provide superior performance and greater tolerances over traditional aperture mask type encoders.
-
Product
IR FPA sensors
-
IR FPA sensors are the most important modules of thermal imagers. Design of sensor electronics (camera core) is a crucial part of designing of new thermal imager. Knowledge of precise parameters of IR FPA sensor is needed by both professionals involved in both IR FPA technology/thermal imagers technology because parameters of IR FPA sensors determine performance limits of thermal imagers. Therefore test equipment that enable measurement of IR FPA sensors is a vital tool for development of both IR FPA technology/thermal imagers technology. It is commonly known that data sheets provided by manufacturers of IR FPA sensors (both cooled or non-cooled) provide too little details for electronics designers. Sometimes the provided data is not accurate enough and better sensor performance can be achieved using modified control signals. Therefore design teams loose sometimes years to develop electronic camera core optimized for a specific IR FPA sensor. When the type of the IR FPA sensor is changed the whole process is to be repeated. In this situation an universal, flexible camera core that would accept IR FPA sensors from different manufacturers and to carry out semi-automatic determination of optimal signal controls for a specific IR FPA sensor would be highly desirable.
-
Product
Concrete Humidity Sensor
BlueRock
-
BlueRock is a rugged, waterproof sensor designed to wirelessly monitor the relative humidity and temperature of concrete from fresh to hardened stages.
-
Product
Force Sensor Elements
-
TE Connectivity (TE) enables OEMs to measure force using MEMS-based technology load cells. The same proprietary piezoresistive silicon strain gage technology used to measure pressure can also be configured into a reliable, low-cost package to measure force.
-
Product
Optical tables
-
The primary goal of a well designed optical table is to eliminate relative motion between components of test system located on the surface of the optical table because such motion can generate measurement errors.
-
Product
Handheld Optical Refractometers
-
Reichert Analytical Instruments
From agriculture, to food and beverage, to veterinary and automotive fluids.
-
Product
Intelligent Optical Power Meter
FPM300 Series
-
Shanghai Tarluz Telecom Tech Co., LTD
Auto-wavelengths Recognition, Referencing Function, Computer Supported, used with FLS300 series Laser/Light Source.
-
Product
Inductive Proximity Sensors (Square)
SP2
-
Easy installation, high-speed pulse generator, high-speed rotation control, and more. A wealth of models ideal for limit control, counting control, and other applications. Sensing distance from 1~2/2 ~ 6/ 5~ 12/10~15mm. Housing by PBT with strong structure and acid resisting available.
-
Product
Cylindrical Inductive Proximity Sensor
-
Shanghai Pubang Sensor Co.,Ltd.
1.Non-contact position detecting,non-wear,high-reliability2.Clear visible indictor design,easy to estimate the working state3.Various type of Sensor,diameter spec.from Φ4 to Φ34,housing length,from ultra-short,short to standard type4.Equipped cable and connector,easy to maintain5.Protection class IP67(IEC)
-
Product
Optical Filter Sets
-
Our filter sets support a great range of fluorophores for microscopes and imaging systems. Patented design techniques drive some of the most spectrally sophisticated optical filters on the market. High transmission, steep edges, precise spectral edge placement, and optimized blocking combine for more reliable measurements. A wide selection of individual bandpass filters and dichroic beam-splitters support unique applications, and world-class manufacturing and cutting-edge metrology ensure consistent performance that always meets specifications.
-
Product
Strain Gauge Sensor
ZET 7010
-
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
