Down Converters
Change a higher frequency signal to a lower frequency.
-
Product
Single-Mode Fiber Optic To RS-232/422/485 Converter
ADAM-4542+
-
1 x SC fiber connectorOperation mode: Point-to-Point,Redundant and Ring(half-duplex)Half/Full-duplex, bidirectional transmission modeAutomatic RS-485 data flow controlLED indicator to monitor status
-
Product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
-
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
-
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
-
Product
HCU/DC-DC Converter ATS
8900
-
Low power testSleep mode current testInput overvoltage limit testLine regulation testEfficiency testLoad regulation testOutput ripple voltage testDC-DC load testOvercurrent testPower doen and isolation test
-
Product
Synchro to Digital-Resolver to Digital Converters
HRDCK-HSDCK
-
Computer Conversions Corporation
HSDCK and HRDCK series are the highest accuracy, miniature tracking synchro and resolver to digital converters in the marketplace. They are designed specifically for ultra precise requirements in the most demanding industrial and military applications.
-
Product
8 channel 16 bit Digital to Analog Module
CPCI-DA8-2
-
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system.
-
Product
Isolated DC-DC Converters
-
power supplies that convert one DC voltage level to another while maintaining galvanic isolation between the input and output circuits.
-
Product
Downed Conductor Detection
-
Schweitzer Engineering Laboratories, Inc.
Downed conductor detection technologies detect many high-impedance faults on a distribution system, improving safety as well as mitigating wildfire risk.
-
Product
1000 Watt AC/DC Power Converter, 6U VPX
VPX56H-6
-
The VPX56H-6 is NAI's latest high power, 1000 Watt AC/DC converter which accepts either a 3Ø 115VAC L-N inputs or a +270 VDC input. It plugs directly into a standard 6U VPX chassis with a (VITA 62) 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Synchro to Digital-Resolver to Digital Converters
MRDC
-
Computer Conversions Corporation
Computer Conversions’ MRDC64-3 is a miniature single chip solution for providing a complete 1 x 64 speed resolver interface into any demanding industrial or military application.
-
Product
Digital to Synchro Converters
DSP
-
Computer Conversions Corporation
The DSP Series are high efficiency, AC Reference powered, Transformer Isolated, continuously updating “whole” Digital to Synchro Converters, designed for high performance Military and Industrial applications.
-
Product
Run Down Adapters
-
Testing power torque tools is essential for product quality and regulatory compliance. A run down adapter is designed is to simulate the fastening process of a screw. Mountz run down adapters improve testing repeatability by adjusting for the impact force and irregular peaks of power tools. Mounted in-line between the tool's driver and transducer, a run down adapter provides consistent and reliable torque readings.
-
Product
Feather & Down Filling Power Tester
TF135
-
TESTEX Testing Equipment Systems Ltd.
Pressure on the sample by dropping the platen is applied to the filling material at a constant speed and after a stipulated time the level of the platen is noted. The massic volume is calculated with regard to the height and the known diameter of the graduated cylinder.
-
Product
Press - Down Fixture Kits
-
*Supports most press - down testers *High - Quality *Precise & Reliabe
-
Product
500 Watt DC/DC Converter, 3U VPX
VPX55H-3
-
The VPX55H-3 is NAI's latest high power 500 Watt DC/DC converter that accepts a +28 VDC Input and plugs directly into a standard 3U VPX chassis with a VITA 62 0.8” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
725-Watt (270VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX57HS
-
NAI’s VPX57HS-31 is NAI's latest +270 VDC Input, VPX DC/DC Converter. The VPX57HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Optical-Electrical Converter - MATRIQ
-
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
Converter
CTD-2160
-
The STD-2160 converter is a device for continuous monitoring and protection of rotary equipment. STD-2160 measures, controls and records signals from sensors continuously through 16 channels.
-
Product
Universal Converter
C8000
-
Multi channel converter for all optek photometric and conductivity sensors and electrochemical pH electrodes. Flexible configuration of sensors, measuring ranges, units and product specific setups make the C8000 converter series a powerful device in process monitoring in both conventional and single-use systems.
-
Product
RF Converters
-
Typically designed for radar or wideband EMC test applications, our frequency converter modules are designed for the conversion between complex baseband waveforms and higher transmitted frequencies. These modules are ideal for integration with digitising modules.
-
Product
Frequency Converter
-
Our frequency converters, which we offer with outputs of up to 500 kVA, can be used to supply alternating current consumers with constant voltages that deviate from the input network.
-
Product
Photometric Converter
C4000
-
The C4000 converter is a multi channel controller capable of operating all optek photometric sensors. The C4000 converter allows for easy programming and operation, and can supply up to four real time configurable 4-20 mA output values correlated to any units of measure. The C4000 offers configurable relay alarms, can record and download process data, and can operate up to four sensors simultaneously.
-
Product
Signal Converters & Load Cell Signal Converter
-
Mantracourt provide a range of signal converter modules which take load cell or strain bridge inputs and provide a data output in a variety of bus and protocol formats. Hardware formats include RS232, RS422 RS485, CAN and USB. Signal converter protocols include Industry Standards such as MODBUS, or Mantracourt’s own proprietary protocols which have been optimised for either ease of use (MantraASCII2) or higher speed communications (MantraBus2).
-
Product
400-Watt DC/DC Converter
VPX55-3
-
NAI's VPX55-3 is 400-Watt DC/DC Converter that plugs directly into a standard 3U VPX chassis with a VITA 62 0.8" power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
IP Converters
-
SMPTE-2022 compliant standalone solutions for conversion between IP and "traditional" DTV signals such as ASI and QAM. These IP converters are hardware-based, providing low latency and zero-jitter transmission of IP signals.
-
Product
Converters
-
ENTES Ethernet Modbus Gateway is an Ethernet / RS-485 MODBUS network gateway which is designed to enable communication with a PC via Internet(WAN) and Intranet(LAN).
-
Product
Scalers / Converters
-
Converter/Scalers provide two essential functions. First, they convert the input signal from one format to another (e.g. analog VGA to digital HDMI). Second, they allow the user to select the resolution of the output signal for display on a flat screen display or projection system. In many cases the quality of the output signal from our Converter/Scalers will be better than what is possible using a direct input on the display because of the price/performance limitations of consumer scaling engines.
-
Product
RS232 to DMX Converter
DS232
-
RS232 to DMX Converter Controller Driver. Connect an RS232 terminal or computer port and drive DMX controlled dimmers and devices. A set of commands and auto fade rates offer power and flexibility for controlling DMX equipment. Use any RS232 terminal application to create command strings to: turn on, off, fade up, and fade down dimmer 256 DMX channels.
-
Product
Antenna Impedance Converter
-
The low noise impedance matching equipment has a high impedance input with minimized capacity. With the 50 Ω output it can be used with common EMI receivers or spectrum analyzers to measure the emissions received by an antenna on a vehicle.
-
Product
Resolver-to-Digital Converter
MSX-RDC-17
-
The resolver-to-digital converter MSX-RDC-17 is a device for supplying and acquiring a resolver. It converts the position value given by the resolver into a digital incremental output signal. The resolution of the incremental encoder output can be defined using the switch on the front side of the MSX-RDC-17.
