Controllers
direct and or manage action.
-
Product
Power Management & MMI Module
H73000700
-
This module, named “6TL-MMI”, is designed to be the interface between an operator and a SYSTEM as well as being a metered power distribution unit (PDU) for it. The module is providing also safety controls, data bus interfaces, temperature control and timers. The 6TL-MMI is suitable for any ATE, and specially for those based on CAN bus controlled devices, because in addition to the above functionalities, this module is also providing galvanic isolation up to 1500V for the CAN bus. This isolation will block potential disturbance towards the DUT.
-
Product
DC Bench Power
XEL Series
-
AMETEK Programmable Power, Inc.
The Sorensen XEL benchtop power supply is as easy to use as simple analog power supplies but offers the flexibility of advanced digital features. The user interface allows easy control with single-turn knobs including a fine control knob for voltage.
-
Product
Data Analytics
-
KLA’s data analytics systems centralize and analyze the data produced by inspection, metrology and process systems. Using advanced data analysis, modeling and visualization capabilities, our comprehensive suite of data analytics products support applications such as run-time process control, defect excursion identification, wafer and reticle dispositioning, scanner and process corrections, and defect classification. By providing chip and wafer manufacturers with relevant root cause information, our data management and analysis systems accelerate yield learning rates and reduce production risk.
-
Product
Production Process Automation System
OPLAN
-
OPLAN v2.6 is a system for production process automation of a television company. The system supports all the stages of operation. From the content ingest, description and preparation, creation of preliminary line-ups and daily broadcasting schedules, registration of commercials and arrangement of commercial blocks, broadcast preparation and automation, to the control and analysis of broadcasting results.
-
Product
SP3T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures 3-way absorptive and reflective switches for use in 50-ohm systems. These SP3T switches operate from 100 MHz to 18 GHz and handle 200 mW input power. VSWR performance is often 1.6:1 or better with 100 ns switching time. Minimum isolation of 60 dB is specified for most units. Absorptive and reflective switches require +5V and -5V power supply to function. Control logic is from 0 to +5 volts. All voltage and ground connections are made by feed thru and turret terminals, respectively.
-
Product
Secure Access
-
Schweitzer Engineering Laboratories, Inc.
Devices with secure access authenticate users, control privileges, and create audit trails.
-
Product
PCI to PMC Adapter / Carrier
PCIBPMCx2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With the PCIBPMCx2´s two slots; a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card.
-
Product
PXI Remote Control Interface Cable, 3m
41-924-300
-
The 41-924-300 is a 3m cable accessory for the PCIe to PXI Remote Control Interface Kit. The kit provides a seamless connection between a PC’s PCIe slot and a PXI chassis and is suitable for providing an interface to any PXI chassis.
-
Product
cRIO-9054, 1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 100T FPGA, 4-Slot CompactRIO Controller
786425-01
-
1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 100T FPGA, 4-Slot CompactRIO Controller - The cRIO-9054 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and four slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Hot Swap & ORing
-
Renesas' positive and negative hot swap controllers enable power supply designers to increase the long-term reliability of their systems. Our latest hot swap controllers include advanced features such as IntelliTrip™ (dual-response to degree of overcurrent condition), adjustable current regulation duration, load current monitoring and integrated charge pumps, making them ideal for hot swap applications.
-
Product
Liquid Thermal Shock Baths
TSB Series
-
CSZ's Liquid thermal shock chambers consist of separately controlled hot and cold baths. Product is submersed in fluid and thermally stressed between the hot and cold baths, resulting in immediate product temperature changes. CSZ uses perfluorinated fluid that does not coat the product or conduct electricity for use in both the hot and cold baths to eliminate cross contamination and reduce evaporation losses.
-
Product
Powered VME64x Crates
6U VME64x 6023
-
The WIENER VME 6023 crate series is the newest generation of 19" integrated packaging system for standard VME/VME64 bus systems with 6Ux160mm cards. Designed primarily for applications in data acquisition, control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
Product
Brushed DC Motor Drivers
-
ST’s STSPIN motor drivers for brushed DC motors integrate a dual current control core and a dual full-bridge power stage to drive two brushed DC motors.
-
Product
High Power DC Electronic Load（1250V）
36300E Series（50KW/60KW）
-
36300E Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
Product
PXI BRIC4 FIBO Matrix Dual 40x4 3pin brkout
40-592A-002
-
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
DC Bench Power
XDL Series
-
AMETEK Programmable Power, Inc.
The Sorensen XDL series II represents the "next generation" of high performance laboratory power supplies. The XDL provides multiple ranges for increased current capability at lower voltages and uses pure linear technology. Unlike other digitally controlled units, the XDL series II provides both numeric and rotary control while the illuminated keys and display legends provide instant confirmation of settings and status.
-
Product
Mini Receiver
FB7-NX
-
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
Product
Hand Multipliers
-
Perfect for service applications, Mountz hand torque multipliers bring power to where your workers need it most. Since they don’t rely on electric, pneumatic, or hydraulic power, hand torque multipliers are great tools for heavy fieldwork. Their small size, light weight, and durable construction make them convenient for field techs to carry, and their strength—up to 36,880 lbf.ft of precisely controlled torque—ensures that your workers can tackle any job. Useful in automotive, heavy machinery, petrochemical, power generation, mining, boring, and shipping, Mountz hand torque multipliers provide maximum capability with minimal investment.
-
Product
Calibration
-
Testwave LLC calibrates electronic, physical, & dimensional test equipment. Our Sparks facility includes a state-of-the-art temperature controlled calibration laboratory, which holds the temperature to within +/- 0.5°C. We send recall notices before your equipment calibration expires, and if we don't hear from you, we will call, to make sure you stay in compliance for your calibration requirements.
-
Product
Temp
-
*Internal and external sensors*Sending an average of values over a given period*Local and remote configuration*Consumption controlled for optimized autonomy
-
Product
Super Phosphor Oscilloscopes
SDS2000X-E Series
-
The SDS2000X-E series employs a new generation of SPO technology. With its excellent signal fidelity, background noise is lower than similar products in the industry. It has a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400,000 frames/sec (sequence mode). It also employs a 256-level intensity grading display function and a color temperature display mode not found in other models in this class. Siglent’s newest oscilloscope offering supports multiple powerful triggering modes including serial bus triggering and decoding. History waveform recording and sequential triggering allow for extended waveform records to be captured, stored, and analyzed. Also included is the deep memory FFT. This math function uses upto 1 M samples for the FFT calculation, providing the SDS2000X-E with very high frequency resolution. The hardware co-processor executes true fast measurement and math to all of 28M sample points so that there is minimal distortion on analysis. It also supports searching and navigating, on-screen Bode plot, 16 channel digital /MSO (optional), an external USB powered 25 MHz AWG function generator module (option), a USB WIFI adapter for wireless control and monitoring (option), and an embedded application that allows remote control via web browser. The features and high-performance of the SDS2000X-E oscilloscopes cannot be matched else anywhere at this price.
-
Product
Pressure Meter
ZET 7112-A VER.2
-
The ZET 7112-A VER.2 pressure meter is intended for use in automated process control systems for various industrial applications:
-
Product
Compressors & Limiters
-
Applied Research and Technolgy
Take control of your dynamics with our range of compressors, limiters, expanders, and gates.
-
Product
Medium Range HD Multi-Spectral Surveillance System
TacFLIR® 280-HDEP
-
The TacFLIR 280-HDEP is an essential system for ground vehicle surveillance and fixed installations. With an all-new stabilized payload assembly for enhanced reliability, the TacFLIR 280-HDEP is ready for a variety of land missions, and the modular and scalable control electronics unit (CEU) is capable of hosting powerful video processing and Aided Target Recognition (AiTR), as well as third-party algorithms. Designed to meet the rigorous demands of military operations, the system delivers best-in-class EO/IR imagery and optional Display Interface Boards (DIB) which allow the operator to stream up to four independent video streams. In addition, there is also a removable terabyte hard drive w/DVR to record over 80 hours of compressed video and 250 screen captures.
-
Product
Panel Controllers
-
AMAX Panel controllers combine HMI displays with CODESYS control in one device, offering various computing options for visualization applications.
-
Product
X2 GPIB Cable,Double-Shielded,Shielded Plug/Receptacles,0.5 m
763061-005
-
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
Product
Heated Dew Point System
DPS3
-
Model DPS3 is a heated dew point hygrometer that can measure dew points up to 95 °C (203°F) and as low as -35 °C (-31°F). This integrated system includes a microprocessor based electronics, a chilled mirror dew point sensor, a sample flow meter/valve, assorted tubing and fittings all contained in a heated, temperature controlled NEMA-4 enclosure.
-
Product
PCI-6518, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Source Outputs, Bank-Isolated Digital I/O Device
779084-01
-
The PCI-6518 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6518 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6518 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
782252-01
-
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Production Stand-Alone
PSA
-
Using PSA, test engineers can build sequences of applications in the built-in AEX (Application EXecutive) manager using if then else goto capabilities. Sequence builders can also include additional capabilities through DOS/Win command line calls, create serial number logged test reports, export tests results to a database etc.. PSA includes drivers for all JTAG Technologies controller hardware past or present.
