Product

Measuring Device for Testing the Effectiveness of Residual Current Protective Devices (RCD) According to DIN EN 61557-6 (VDE 0413-6)

-

PeakTech Prüf- und Messtechnik GmbH

PeakTech Prüf- und Messtechnik GmbH

A residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE).

Product

Hall Effect Proximity Switches/Sensors

-

ChenYang Technologies GmbH & Co. KG

ChenYang Technologies GmbH & Co. KG

A Hall Effect proximity switch is a non-contact electronic switch, which consist of a permanent magnet or ferromagnetic part as trigger intermediary and a Hall Effect sensor IC. The Hall sensor IC detects the change of the magnet field when the permanent magnet comes in the close proximity to it and generates an electric signal. This signal is amplified and rectified to control the output signal of the switch.

Product

Hall Effect DC Current Sensor

CYHCT-L20K

-

ChenYang Technologies GmbH & Co. KG

CYHCT-L20K - ChenYang Technologies GmbH & Co. KG

The sensor CYHCT-L20K is based on open loop principle and designed with a high galvanic isolationbetween primary conductor and secondary circuit. It can be used for measurement of DC current, DCpulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.

Product

RF Shielded Enclosure for Pre-Compliance EMC and CTIA Testing

QuietBox-AR "Mini-Range"

-

Raymond RF Measurements Corp.

QuietBox-AR "Mini-Range" - Raymond RF Measurements Corp.

The Raymond RF QuietBox-AR is a mobile solution for pre-compliance EMC and CTIA testing, 3D antenna pattern measurement, and total radiated power & total isotropic sensitivity testing. Fully equipped with client-specified broadband absorber, integrated antenna and rolling cart, the QuietBox-AR is a cost effective option for product verification prior to fully compliant testing.

Product

10 Ft Shielded Cable For 5xxx/35xx Products (68 Pin)

GT95028

-

Marvin Test Solutions, Inc.

GT95028 - Marvin Test Solutions, Inc.

10 ft shielded cable for 5xxx/35xx products (68 Pin)

Product

Easy-to-assemble and Collapsible RF Test Enclosure With Fabric Shielding, ≥ 90 DB Isolation, 300 MHz - 18 GHz

dbTENT

-

DVTest Inc.

dbTENT - DVTest Inc.

The dbTENT is an easy-to-assemble, store and transport high-performance RF test enclosure. Whether you need to make measurements in the field or in the lab, the dbTENT provides superior 90 dB of isolation over a wide frequency range thanks to its patented double layer conductive fabric design. Featuring an interchangeable customisable I/O panel, the dbTENT meets all your needs for non-permanent isolated testing. With a setup time of only minutes, the dbTENT will get you ready for testing instantly in a wide variety of environments.

Product

RF Shielded Test Enclosure, for Laptop Testing

JRE 2218

-

JRE Test, LLC

JRE 2218 - JRE Test, LLC

Breeze through laptop RFI and wireless tests with the 'bigger than-a-breadbox' 2218! Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan.

Product

MAX31855 J-Type Thermocouple Arduino Shield

SEN-30004-J03

-

Playing With Fusion Inc

SEN-30004-J03 - Playing With Fusion Inc

Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega

Product

MAX31855 T-Type Thermocouple Arduino Shield

SEN-30004-T47

-

Playing With Fusion Inc

SEN-30004-T47 - Playing With Fusion Inc

Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.

Product

Effective Irradiance Radiometric Probe

LP471BLUE

-

Senseca

LP471BLUE - Senseca

The radiometric probe LP471BLUE measures the IRRADIANCE (W/m2) in the spectral range of Blue light.

Product

3 Ft Shielded Cable For All 5xxx/35xx (68 Pin)

GT95022

-

Marvin Test Solutions, Inc.

GT95022 - Marvin Test Solutions, Inc.

3 ft Shielded Cable for all 5xxx/35xx (68 Pin)

Product

Hall Effect Measurement system

HMS-3000

-

ECOPIA

HMS-3000 - ECOPIA

Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.

Product

Rotary Hall Effect Sensor

-

Motion Applied

Motion Applied

The output of the Rotary Hall-effect sensor is a voltage which changes in direct proportion to the shaft angle. The sensor is non-contact, using Hall elements to determine the angle of a magnet. The magnet is either mounted in a shaft integral to the sensor or can be mounted externally to the sensor.

Product

Shield

Arduino MKR ENV Shield rev2

-

Arduino

Arduino MKR ENV Shield rev2 - Arduino

The MKR ENV Shield allows a MKR board to acquire environmental data collected by an array of sensors.

Product

19" Rackmount Drawer with Keylock, Shielded, 7"H x 20"D

DR-071920-K

-

ELMA Electronic, Inc.

DR-071920-K - ELMA Electronic, Inc.

Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock

Product

Hall Effect Speed Sensors

-

SPECTEC Innovative Sensor Solutions

SPECTEC Innovative Sensor Solutions

SPECTEC zero speed Hall effect gear tooth sensors are used in industrial applications to determine shaft or gear speed or direction by detecting fluctuations in the magnetic field. The Hall effect technology fulfills a wide array of applications due to a Hall effect sensor's ability to detect zero speed and the quadrature sensor's ability to detect direction change. The Hall effect gear tooth sensor's digital output is easily read by computers, motion control devices, position monitors and digital to analog converters. Intrinsically Safe zero speed sensors are available for various applications.

Product

RF Shielded Test Enclosure, Slim rack mountable

JRE 1724A

-

JRE Test, LLC

JRE 1724A - JRE Test, LLC

Designed for testing devices with a flat form factor that need plenty of I/O, the rack-mountable JRE1724A is ideal. Similar to our JRE1724, but not as high, you can place multiple devices within its large footprint. Dual I/O panels allow for a multitude of connectors and interfaces. The JRE1724A comes standard with dual honeycomb style vents - pictured is the enclosure with optional cooling fan and USB2.0 interface.

Product

Lightning "Emulator" Shield

SEN-39002

-

Playing With Fusion Inc

SEN-39002 - Playing With Fusion Inc

Arduino shield, ideal for AS3935 lightning sensor development. The lightning "emulator" generates a RF signal that mimics lightning strikes. This board is in an Arduino Uno form factor, and only uses GPIO and I2C, so can be stacked on many form factors (developed on an Uno and Mega).