White Noise
Noise which is equal in intensity across a band, at all frequencies.
See Also: Noise, Pink Noise, RF Noise, Noise Generators
-
Product
Broadband Calibrated Noise Sources
-
Fairview Microwave’s calibrated noise sources cover frequency bands from 10 KHz to 18 GHz. Their performance specifications include output ENR levels ranging from 15 dB to 30 dB and typical VSWR levels as low as 1.25:1. Depending on the model, calibrated frequency points are at 10 MHz, 100 MHz, 1000 MHz, 2000 MHz and 1 GHz steps. The temperature coefficient of these noise sources is < 0.01 dB/°C and noise output variation is < 0.1 dB/%V.
-
-
Product
Precision Calibrated Noise Sources
-
ELVA-1's calibrated noise source ISSN-XX series delivers a uniform level of noise power spectral density within the whole waveguide frequency range. Sources are available in eight waveguide bands covering 26.4-170 GHz.
-
Product
Mechanical Noise Tuner Control
S93027B
-
The S93027B enables to control Maury Microwave’s LXI tuner as the impedance tuner and measure the noise figure of unmatched devices (Gamma opt. < 0.9) with the N524xB PNA-X with option 029 and the S93029B noise figure measurement software.
-
Product
White Light Continuum Generator
JIBE
-
A powerful coherent light source. Due to its amazing wide spectral band, the white light continuum is being applied in different areas such as optical parametric amplification, optical metrology, optical coherence tomography, materials characterization, etc.
-
Product
Noise Source Family
346 Series
-
This series of broadband noise sources has been designed to cover the majority of measurement applications with a range of frequencies, Excess Noise Ratio (ENR) and coaxial connector types.
-
Product
Phase Noise Testing
-
The systems are based in the UK although testing for any company world wide will be undertaken.
-
Product
Ultra Low Noise Preamp
J2180A
-
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
Product
Noise Dosemeters
-
Noise Dosemeters are a type of sound meter designed to measure the levels of noise exposure to an individual over a period of time. All of our dosemeters are compliant to IEC 61252: 1993 / BS EN 61262:1997 and offer high quality and reliable personal noise monitoring solutions.
-
Product
Low Phase Noise Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM is committed to an expanding portfolio of low-phase noise (>150dBc/Hz @ 1k Hz offset) amplifiers for critical signal generation applications in test and measurement and defense. These offerings complement our line of NLTL GaAs comb generators.
-
Product
Site Vibration And Noise Testing
-
Response Dynamics Vibration Engineering, Inc.
Effective vibration isolation is critical to the performance of many systems. It is often much more challenging than expected because the structural dynamics of the supporting structure, and the isolated structure, also affect the isolation performance. Isolation resonances can often create other vibration problems and confound an engineering team. We have successfully designed vibration isolation into countless systems over the years using unique custom solutions as well as adapting standard components and applying them properly to the design.
-
Product
Noise and Vibrations Meters
Ga113
-
Noise e vibrations metersGa113category: Monitoring / Noise e vibrations metersbrand: CASTLEitem: Ga113 The Castle SONUS is a new range of pocket meters designed for ease of use with the power the cover the work you need, from Noise at Work measurements to Environmental monitoring. The SONUS sound level meters are split into a range of meters to suit specific needs.
-
Product
Noise Nuisance Recorder
Trojan2
-
The Trojan2 Noise Nuisance Recorder was designed in conjunction with Local Councils, Environmental Health Officers and Housing Associations to allow you to easily measure, monitor and record noise nuisance.
-
Product
High-Power Noise Sources
-
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
Product
Noise Analysis Software
noiseLAB
-
noiseLAB is a professional software recording and analysis package for making Type 1 Precision measurements to international standards. Precision Recorder: noiseLAB makes high quality recordings of up to 8 channels of sound. Precision Analysis of: Sound Level (Fast, Slow, Impulse, Taktmak. Custom Time Constant, Leq). Statistical Values (L1, L5, L10, L50, L90, L95, L99). Octave Spectra (1/1, 1/3, 1/6, 1/12, and 1/24th octave).....
-
Product
Noise Figure Measurements With Vector Correction
S93029B
-
The S93029B noise figure application enables high-accuracy noise figure and noise-power measurements of amplifiers, frequency converters, and mixers, utilizing Keysight’s unique vector-source-correction technique
-
Product
End of Line Noise Test System
-
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
Product
Permanent Outdoor Noise Monitor
NMS043
-
For permanent and semi-permanent outdoor noise monitoring where remote access is required, the NMS043 is an excellent choice. When you need online access to noise data for monitoring construction noise, nuisance noises, transportation noise or other unwanted noises, the NMS043 will reliably do the job.
-
Product
Environmental Noise Monitoring System
E-Box LIVE
-
This is the ultimate solution to environmental noise monitoring. The LIVE comes equipped with a modem that connects directly to our Castle Cloud software allowing you to monitor your results from the comfort of your own desk. Combine this with the ability to customise your power supplies and you will see why this is the ultimate solution for environmental noise monitoring.
-
Product
Phase Noise Analyzer
NXA-26
-
This new NXA-26 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 26.5 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range. The NXA-26 combines over 25 years of Phase Noise Measurement Technology with an easy to navigate user interface. System operation requires minimal training that will have you making measurements in minutes.
-
Product
Low Noise Triaxial Cable
PX0102A
-
The Keysight PX0102A is suitable for low current measurement down to the sub-fA level. It supports the Keysight M9601A.
-
Product
Optical Noise Analyzer
A0040A
-
Optical Noise Analyzer is the industry first solution for evaluation of optical frequency noise of lasers as power spectrum density.
-
Product
Noise Receiver Modules And Noise Switching Modules
MT7553 Series
-
Noise Parameters are the non-50Ω extensions of Noise Figure, and are an important modeling and model validation tool to understand how a device-undertest’s performance changes as a function of source impedance. Noise Parameter measurements are typically performedusing a Vector Network Analyzer (VNA) to measure the S-Parameters of the DUT, and a Noise Analyzer (either Noise Figure Analyzer NFA or Spectrum Analyzer SA) to measure the noise power of the DUT. Noise parameters are calculated from a combination of knownsource impedances, S-parameters and noise powers.
-
Product
Noise Test
-
Noise testing is conducted to determine if materials can withstand external noises generated by various sources. It also includes air-borne and structure-borne noise measurements.
-
Product
Phase Noise Analyzer and VCO Tester
FSWP
Phase Noise Analyzer
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
Product
Noise Figure Measurements With Vector Correction
S96029B
-
This software application enables high-accuracy noise figure and noise-power measurements of amplifiers. It utilizes Keysight’s unique vector-source-correction technique, which uses a source-impedance tuner to remove the effects of imperfect system-source match. This approach yields accuracy that surpasses that provided by the Y-factor method and other cold-source implementations, especially for in-fixture, on-wafer, and automated-test environments. A scalar-calibrated method is also available that offers less accuracy but is faster and does not require an impedance tuner.
-
Product
Interferometers (White Light)
interferoMETER
-
The innovative white light interferometers from Micro-Epsilon set a benchmark in high-precision distance and thickness measurements. These sensors enable stable measurement results with sub-nanometer resolution offering a comparatively large measuring range and offset distance. The interferometers are available in 3 series: the IMS5400-DS for high-precision industrial distance measurements, the IMS5400-TH for accurate thickness measurements and the vacuum-suitable IMS5600-DS for distance measurements with picometer resolution.
-
Product
Compact WCA Noise & Vibration analyzer
AD-3651
-
Noise & vibration analyzer, from in-vehicle order tracking to MIMO analysis. Compact WCA for analysis of noise and vibration for in-vehicle order tracking analysis.The long time experience and know-how of A&D in the automobile field of instrumentation and listening to user suggestions are what gives the A&D model the lead with its unmatched specification and functions. Best of all is its compact size and light weight. At the same time, all the functions you would expect to find in multi channel noise and vibration analyzers are included, plus more enhanced features.
-
Product
Low Noise Amplifier
-
The COMM-connect Low Noise Amplifier can be used to amplify signals in a wide range of bands. The amplifier comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
Brake Noise Testing
-
Brake Noise Testing - Brake Squeal AnalysisDewesoft Brake Noise testing solution, also known as Brake Squeal, is ideal for detecting and tracking noise caused by mechanical vibration in various braking systems based on the VDA 303 guideline algorithm.
