Automation
-
product
Multiport Coaxial Switch, DC to 4 GHz, SP4T
87204A
The Keysight 87204A terminated multiport switch provides the life and reliability required for automated test and measurement, signal monitoring and routing applications. Innovative design and careful process control created the Keysight 87204A which meet the requirements for highly repeatable switching elements in test instruments and switching interfaces. The Keysight 87204A is designed to operate for more than 10 million cycles. The exceptional 0.03 dB insertion loss repeatability is warranted for 5 million cycles at 25° C. This reduces sources of random errors in the measurement path and improves measurement uncertainty. Switch life is a critical consideration in production test systems, satellite and antenna monitoring systems, and test instrumentation. The longevity of this switch increases system uptime, and lowers the cost of ownership by reducing calibration cycles and switch maintenance.
-
product
Zeta Potential & Particle Size Analyzer
AcoustoSizer II
The new AcoustoSizer IIs provides thorough characterization of concentrated colloidal dispersions. Directly measuring particle size, zeta potential, pH, conductivity, and temperature, it furnishes the most comprehensive analysis available in a single, turnkey instrument. Based on a flow-through sensor design, the AcoustoSizer IIs can be used in a laboratory batch analysis mode or connected directly to a process slipstream. Built-in syringe pumps provide automated potentiometric and volumetric titration capabilities for accurate isoelectric point and surfactant addition determination.
-
product
Automated DC Parametric Curve Tracer
MultiTrace
MultiTrace curve tracer is a mid-sized benchtop model supporting pin counts from 216-625 pins and includes the PGA-625 fixture as a standard interface. MultiTrace supports a wide range of test applications: Failure analysis, Reliability testing, Counterfeit device analysis, Nondestructive electrical counterfeit test, Opens, shorts leakage testing (OSL), Post decap electrical inspection, Optical fault localization, ESD testing, Latch-up testing, Supply current measurements, and more!
-
product
PXIe-5110, 100 MHz, 1 GS/s, 8-Bit PXI Oscilloscope
785768-01
PXIe, 100 MHz, 1 GS/s, 8-Bit PXI Oscilloscope—The PXIe-5110 oscilloscope has two channels that sample up to 1 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated applications that require flexible measurement configurations and up to 100 MHz of analog bandwidth. The PXIe-5110 also features advanced PXI synchronization and data throughput capabilities. Some options also support CableSense™ technology, which can detect and locate signal path faults, changes, or discontinuities.
-
product
Server Power And Back Up Unit Test Solutions
Built on the proven Chroma 8000 ATS platform, these customizable solutions are specifically designed for automated testing of server PSUs, power shelves, rack power systems, bidirectional DC/DC converters for BBUs, and low-voltage high-current DC/DC converters for motherboards.
-
product
Distribution Automation
Schweitzer Engineering Laboratories, Inc.
Scalable and modular distribution automation solutions help increase system operational efficiency and reduce operating costs.
-
product
Thickness and Flaw Inspection
FOCUS PX / PC / SDK
Olympus offers a complete advanced phased array integration solution that meets the requirements of your most demanding customers. The solution includes the FOCUS PX, a powerful and scalable acquisition unit; FocusPC, a powerful data acquisition and analysis software program; and three software development kits (SDK), FocusControl, FocusData, and OpenView SDK, to customize your software interface based on your application and control FocusPC for a fully automated inspection solution.
-
product
Test Accessories
Qosmotec Software Solutions GmbH
Qosmotec test systems are expandable to adapt your automation environment to increased demands. Standard components that can be easily integrated into an existing test setup are
-
product
Compliance and Data Protection
Locate and protect sensitive and PII data to identify risk and ensure compliance. Monitor system events to identify and proactively respond to potential risks and bad actors. Simplify security operations, reduce risk and lighten security management load with automated ID and authorization cleanup.
-
product
High Performance Fanless Embedded Box PCs
ARK-3000 Series
The Fanless PC ARK-3000 series features high performance computing Intel Core i, up to Quad core i7, boasts versatile expansions – 2 PCI, PCIe x1, PCIe x4, MIOe module and 2 MiniPCIe to fulfill diverse applications. Complete storage options include 2 hard drives or SSD/ 2 mSATA/ Cfast, and there is also optional wireless communication Wi-Fi / 3G / GPS support. As for rugged design, ARK-35 series supports wide-range power input: 9~34V/ 12V D. They combine all the benefits of performance, expansion, and storage ideal for machine automation, factory automation and cabinet integration.
-
product
Open Frame Panel PC
By highly flexible configuration with a high level of modularization, ADLINK's Open Frame Panel PC, leveraging Intel® x86 and NXP ARM-Based solutions, with ready-to-use design helps system integrators, integrated solution providers, and brand vendors quickly deliver cutting-edge functions to individual HMI applications. Leveraging our unique Function Module (FM) design, these industrial panel PCs accelerate prototyping according to the application's requirements while saving considerable time, money, and effort. The SP2 series is ideal for industrial automation, transportation, retail, healthcare, gaming, and other industries.
-
product
Universal Testers
All of our Universal Testers can be manufactured to utilize manual loading, manual loading with auto unloading, or automated load/unload. The interweaving of slip sheets between each PCB is available as well when utilizing an automated load/unload system.
-
product
Specific Heat Capacity
The heat capacity probe uses a miniature AC calorimeter to measure the heat capacity of samples weighing as little as one microgram. The AC technique employed is highly sensitivity and combined with the automated Cryogenic Software, is simple to use.
-
product
EBIRST 200-pin LFH Test Tool
93-002-001
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Material Identification Spectroscopy
ChipCHECK
Gastops specializes in advanced fluid sensing and analysis systems specifically designed and developed for critical equipment condition monitoring applications. ChipCHECK offers the fastest way of making on-site equipment maintenance decisions. It is a field deployable analyzer designed for rapid on-site identification of equipment lube oil. This automated maintenance decision-support tool employs innovative laser spectroscopic technology, which enables on-site analysis of microscopic chip debris. ChipCHECK provides the maintainers with quick, reliable, and conclusive information, including the total number of particles, and the size, shape, and specific alloy classification for each individual particle on the sample.
-
product
Automatic Calibration Module
ACM4509
ACM4509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full four-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to 18 connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
product
HART Protocol Stack
softHART
SoftHART is the industry-standard smart HART (Highway Addressable Remote Transducer Protocol) communications stack for industrial automation. HART is a bidirectional protocol and communicates over existing 4-20 mA analog current loops, extending communication capabilities without the inconvenience of installing additional wiring.
-
product
PXI Opto-Iso Digital I/O 32bit out 16bit in
40-491-002
The 40-490 Digital I/O Modules are designed for applications requiring optically isolated digital I/O, typically in industrial automation. This modules features 32 digital outputs and 16 digital inputs which may be programmed by word or individual bit. Power for the isolated section of the module is built onto the board in model 40-490-001, or this can be supplied externally in model 40-490-002.
-
product
PXIe-6375, 208 AI (16-Bit, 3.8 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
783634-01
PXIe, 208 AI (16-Bit, 3.8 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6375 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6375 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Wafer Prober
Prexa
The latest fully automated 300mm wafer prober. The system offers excellent productivity and advanced functions, contributing to KGD (known good die) testing for advanced packaging.
-
product
Signal Analysis Software
Signal analysis software solutions support a wide spectrum of applications ranging from manual signal processing and individual signal analysis to fully automated signal recognition and processing in wideband scenarios. The products are available as standalone units or as integrable subsystem solutions for R&S COMINT system software or third-party system software.
-
product
Particulate Filter Management System
PFS-ONE
The highly precise weighing of emission particles has become increasingly important due to new legislative regulations such as Euro 6, WLTP, EPA 1066 or PM 10. PFS-ONE, the Particulate Filter Management System offers different weighing methods. This supports full compliance with current legislation in the automotive and environmental industry and also allows for flexibility of internal testing processes. The system covers the measurement, organization, tracking and control of particulate filter weighing. Built as a modular system, the PFS-ONE can be expanded from a stand-alone installation up to a fully integrated laboratory module and can be used for manual weighing or automated weighing via a robot.
-
product
Test System
Maynuo Electronic Co.,Ltd a professional R & D and production of programmable DC electronic loads, programmable DC power supply, high power load, power supply, AC power supply, power supply, such as testing high-performance mobile phone test equipment and facilities, as well as electrical, electronic, aerospace, military, chemical, automotive, battery charger, battery, solar cell production lines and other industries to provide automated testing program. The company has many years experience in a number of outstanding technical R & D, product innovation by the majority of users. We are committed to provide users with more accurate and more stable more easily accessible to the higher cost of test instruments, to create the industry in testing the influence of an international brand of excellence.
-
product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
product
Semiconductor Testers
Designing and manufacturing scalable Automated Test Equipment (ATE) targeted at testing SOC, MCU, RF PA/FEM, Sensors/MEMS and Power and Analog devices
-
product
Measurement Hardware
Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.
-
product
Autonomous Vehicle Simulation
Ansys Autonomous Vehicle Simulation provides a solution designed specifically to support developing, testing and validating safe automated driving technologies. This autonomous vehicle simulation solution saves significant time and costs versus traditional development and testing methods by allowing you to exercise your AV/ADAS software stack in a closed loop, with sensor-accurate synthetic data in software-in-the-loop or hardware-in-the-loop context with the driving simulator of your choice.
-
product
Advanced Power System - DC Power Supply, 80 V, 25 A, 2000 W
N6974A
The N6974A is designed for automated test equipment (ATE) applications where high performance is critical.
-
product
PXI-2532B, 512-Crosspoint PXI Matrix Switch Module
782383-01
512-Crosspoint PXI Matrix Switch Module—The PXI‑2532B is a high-density PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring compact reed relays with switching speeds up to 2,000 cycles/s, the PXI‑2532B can be configured in more than 10 matrix topologies by using different terminal block accessories. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
OTDR Automation Software
OASYS.net
Both the 1000i and 1000 OTDR Automation Systems consist of a suite of PK products that accelerate and simplify several time- consuming activities that are a common to the OTDR testing process in cable manufacturing. The cornerstone of both systems is the OASYS.net OTDR Automation Software. OASYS.net provides cable manufacturers with the ability to define comprehensive OTDR testing strategies, to execute these strategies to automatically acquire and analyze the OTDR data, and then organize and package the large quantity of test data in a form that is compatible with existing factory information systems.
