Light Fixture
-
Product
Optical Light Sources
FLS100 Series
-
Shanghai Tarluz Telecom Tech Co., LTD
FLS100 Optical Light source could provide maximum 4 wavelengths in one unit, it is an cost effective solution to work with FPM100 series optical power for installing fiber optic network. The unit support Single mode and Multimode (50/125um or 62.5/125um MM fiber) optical cable in one unit. It could support FC, SC, ST, LC and 2.5mm universal optical connector.
-
Product
CTR Test Fixtures
-
Designed to hold electronic components or assemblies in place during testing, particularly for verifying the Current Transfer Ratio (CTR) of optocouplers.
-
Product
Evaporative Light Scattering Detector for HPLC
ELSD-LT III
-
The evaporative light scattering detector (ELSD) is a general-purpose universal detector that can even detect components with no UV absorption, such as carbohydrates, lipids, surfactants, and synthetic polymers. With exceptional sensitivity, a wide dynamic range through Analytical Intelligence features, and easy operability using LabSolutions™ software, the ELSD-LT III contributes to more effective analysis in a wide variety of fields.
-
-
-
Product
Ultra-Broadband Light Soure
Cannon
-
Cannon provides a turnkey portable source of broadband laser pulses without reqiring any user-adjustments to the fiber coupling. Optical Spectrum - 1000 - 1900 nm.
-
Product
In-Line Functional Test Fixtures
-
Add an advantage to in-line production with fast change over interchangeable fixturing. Circuit Check’s in-line board handlers and in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading handlers.
-
Product
RF Chamber Fixtures
-
- 12” W x 12” D x 8” H internal dimensions- RF mechanical chamber can fit various wireless and Bluetooth products- test either commercial or consumer
-
Product
Light Analysis
-
Welcome to Thorlabs; below you will find links to detectors and instrumentation that measure the various properties of light, a subset of our entire line of photonics products. Thorlabs offers an extensive selection of instruments that measure the properties of light. Our versatile power and energy meters can be used with over 25 different sensors in order to make NIST-traceable power and energy measurements. If the convenience of a meter is not desired, our selection of detectors includes basic photodiodes (uncalibrated and calibrated), photodetectors (biased, amplified, and avalanche), CCD and CMOS arrays, position detectors, integrating spheres, and photomultiplier tubes. The Beam Characterization category contains beam profilers (camera and scanning slit), a wavefront sensor, spectrometers, and interferometers, while the Polarimetery link leads to a selection of instruments used to measure and control the polarization of light.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg
-
Product
Functional Test Fixtures
-
EMC Technologies designs and manufactures discretely wired and wireless functional test fixtures used for performance verification of PCBs and Electronic Assemblies. Commercial applications have included work in support of many industries including: satellite TV, computer servers, medical, networking, and telecommunication.
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
Test Fixtures
-
Pneumatically actuated Kelvin connection to custom manufactured device inserts either to complement ART's wide range of precision parametric test equipment or for use with third party measurement hardware.
-
Product
C-Band ASE Light Source
ASE5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ASE5000 series is C-Band ASE light source with featured with high stability and high output. It is mainly applied for testing of C-Band optical components and optical communication equipments as well as Fiber Optical Sensor etc. Huatai ASE5000 has three types of exterior structure, suitable for different customer’ requirements.
-
Product
Stand-Alone Test Fixture
MA 2013/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 22,00 kg
-
Product
Enhanced UV Light Source
Model 30E
-
The Model 30E Enhanced UV Lightsource is highly efficient and may be utilized in a variety of applications. Light is collected by an ellipsoidal reflector and focused on an integrating/condensing lens array to produce uniform illumination at the exposure plane. This UV light source is available in various beam sizes up to 24 inches square with output spectra ranging from 220 nm to 450 nm, using the appropriate lamp (included). Output power ranges from 200 watts to 5 kilowatts. All OAI UV Lightsources are easily equipped with quick-change filter assemblies, enabling the user to customize the output spectrum with little effort. Optional remote exhaust fans are available.
-
Product
Universal Test Fixture
Series 48
-
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
Product
LED Light Measurement System
-
RayClouds Photoelectric Technology Co.,Ltd.
The LED optical measurement system includes Blue Light Analyzer, Glare Analyzer, LED Light Intensity Measurement, LED Goniophotometer, Lighting Electrical Measurement System, LED LightBar Measurement System, LED Photochromic Tester.
-
Product
Becker NAV/RMU/RMI/OBS Test Fixture
TA-3320
-
This NAV test fixture is specific to the requirements for testing Becker Avionics NAV, RMI and RMU products. The panel incorporates specific functionality required for testing these Becker products by the book including special requirements for the RMU 5000 and the IN 3300 series of nav indicators. This BAEE NAV test fixture also facilitates resolver alignment and discrete meter testing through the PG 3300 interface connector. The RM 3300 portion of the panel tests the Becker RMI indicators and allows for sourcing the composite signal from the paired radio or from an external generator. The DME channeling outputs are monitored with discrete LED's as well as the ILS, V/LOC, Glideslope and NAV TEST valids. Discrete test jacks are provided for all the meters and the resolver of the NAV indicator and a dimming source is also provided. When testing the RMU 5000 computer access is through a dedicated connector.
-
Product
Smart Lighting Management
-
Single-chip solutions enable IoT connectivity and precise control of smart lights and replacement lamps.
-
Product
Light Intensity Meter
MT-4617
-
Measures the visible light produced by fluorescent lamp, metal-halide lamp, high voltage sodium lamp or electric incandescent lampBuilt-in precision photo diode sensor and color correction filterAutomatic and manual measured range switchingRelative and peak value measurementMeasures up to 200,000 lux / 20,000 FCExtra functions: Max./Min. value displayOver load indication/Low battery indicationAuto power offBacklightData hold, Zero calibration
-
Product
Xenon Light Sources
-
Our pulsed Xenon light source is used in applications where a long lifetime and high output power is needed, such as in fluorescence measurements. This is an affordable UV source, but the spectral output is not as smooth and continuous as the AvaLight Halogen and Deuterium light sources.
-
Product
Low Light USB Camera With Microphone
Conversa
-
Conversa, camera for conversation (See3CAM_CU38), is a 3.4 MP low light USB 3.1 Gen1 camera with built-in stereo microphone providing 16bit audio @48KHz. This low-light USB camera is the next advanced version of our flagship product See3CAM_CU30, with built-in stereo microphone for crystal clear sound. It is a plug-and-play (UVC and UAC) compliant USB 3.1 Gen1 SuperSpeed camera and is also backward compatible with USB 2.0 host ports. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It has a dedicated, high-performance Image Signal Processor chip (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control).
-
Product
USB-C® – USB 2.0 Plug HS SQ Test Fixture
AUT17094
-
This product is designed for USB-C USB2.0 Receptacle Host Electrical Test.
-
Product
Ambient Light Sensors
-
Bristol Industrial & Research Associates Ltd
Ambient light sensors measure background or ambient light levels. Biral sensors are typically used in aviation Runway Visual Range (RVR) systems and have a well defined field of view.
-
Product
Food Grips and Fixtures
-
AMETEK Sensors, Test & Calibration
We supply material testing instruments to some of the world’s most innovative companies within the food industry. The reason for this is our extensive experience within food testing, combined with our high precision texture analysis and packaging test systems.
-
Product
10 PCS Deluxe Noid Light / IAC Kit
3610
-
Peaceful Thriving Enterprise Co Ltd
Kit packs in a deluxe mold plastic case. Set includes: 8 Noid lights for testing GM PFI, FORD TBI, GEO TBI, BOSCH 2, BOSCH PFI, GM TBI, GM SCPI and GM MULTEC 2. One IAC signal test lights for GM 1982 or newer GM TBI and PFI fuel injection system, and one for GM Model 1987 or newer GM Model 700 TBI and PFI fuel injection system.
-
-
Product
Audio Panel/Amplifier Test Fixture
TA-200
-
The Model TA-200 test panel was designed to allow Avionics shops the capability to test and troubleshoot both today's new generation audio panels as well as the standard audio panels of the past. The testing of these panels over the years has always proven to be a very time consuming job for most shops because of the limited capabilities of any past test panels.
-
Product
Light Section Sensors for Object Detection
-
Leuze electronic GmbH + Co. KG
Switching light section sensors are designed to perform scanning, two-dimensional object detection along a laser line. They are especially well suited for completeness monitoring or product monitoring in the case of multiple track transport. The short measurement time and the detection range from 200 to 800 mm enable an inspection of the content at a high throughput rate even with deep containers. The internal data processing offers programming and differentiation of 16 different object types, thereby conserving control capacity. Complex detection tasks can be solved with one sensor. The compact housing ensures high flexibility during installation and saves installation space.
