Prototype Boards
-
Product
EIA Based VectorPak
-
VECTOR Electronics and Technology, Inc.
VectorPak™ subracks offer versatility within a 19” rackmount format. All racks are adjustable in both height and depth, offering standard product solutions for standard and custom requirements. All Subrack sizes are compatible with Vector prototyping boards (see Vectorbord® Plugbord™ section), and can accommodate other sizes as well.
-
Product
HES Prototyping Boards
-
HES™ is a feature-rich family of SoC/ASIC pre-silicon physical prototyping and hardware emulation boards. The family features boards with high-performance devices from either Xilinx (including Virtex-7, Virtex UltraScale, Virtex UltraScale+ and Zynq UltraScale+) or Microchip (PolarFire and SmartFusion2).
-
Product
RF Prototyping Kit
VXI-5501
-
* VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
Design for Test
-
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
-
Product
Breadboard to DAQ Converters
0001026-1 / -2
-
VI Control Systems has designed two converter boards that make it easy to connect data acquisition boards to breadboards and allow easy computer control and monitoring of prototyped electronic circuits. The converter boards are 0.8 x 3.5 inches and have silk-screened pin numbers for every pin on the board. The 68-pin SCSI converter can also be used to connect 68-pin SCSI cables to prototype solder boards that have 0.1 inch centers.
-
Product
TySOM Embedded Prototyping Boards
-
TySOM™ is a family of embedded system prototyping boards. Depending on the board, one of three FPGAs will be at its heart: a Xilinx Zynq® UltraScale+™, a Xilinx Xilinx Zynq-7000 or a Microchip PolarFire SoC. The boards are compatible, through industry standard interfaces (FMC or BPX), with Aldec’s wide range daughter cards, making Aldec’s TySOM embedded prototyping boards ideal for the rapid development of applications that include automotive (and ADAS, in particular), artificial intelligence (AI), machine learning (ML), embedded vision, embedded-HPC (including edge-processing), IoT, IIoT and industrial automation.
-
Product
Digital System X
DSX
-
We have developed this technology, not only for our customers, but for our own unique needs in the areas of prototyping and test. We found that many of the standard digital prototyping boards (FPGAs, PLDs, etc…) that are available on the market, did not have the flexibility or the base architecture to provide the prototyping capabilities we need in developing our own solutions.
-
Product
RF/MicrowavePrototyping Boards and Housings
MicroAmp2
-
MicroAmp2 is a new series of RF/microwave prototyping boards and housings that allow for rapid construction of custom circuits in a fraction of the time and cost of traditional solutions. With the MicroAmp2 series of MB boards, a designer can quickly build amplifiers, filters, passive networks, multipliers, prescalers, log detectors, oscillators, and opamps using many popular components. A growing line of MB circuit boards are available to fit many of the industry-standard components, which can be easily assembled and mounted into shielded RF housings to create fully functional modules. Select parts from popular manufacturers such as Analog Devices, Avago, CEL, M/A-COM, Mini Circuits, RFMD, Triquint, and others.
-
Product
DUT Prototype Board
DPB8800
-
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
Product
PXI, CPCI Development And Prototyping Board
TE2100
-
Team Solutionsí PXI Development and Prototype board is the fastest road for system integrators to deliver a PXI customized product and provides design engineers with a speedy avenue to release PXI based prototypes and products.
-
Product
Supported Test Systems
-
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
Product
Software
HES Proto-AXI
-
The HES Proto-AXI™ software package, when combined with our HES™ prototyping boards, provides an efficient and robust environment for rapid design prototyping and/or algorithm accelerator development and bring-up.
-
Product
Prototyping Kit
VXI-5502
-
* VXI-5502 has a Sea-of-holes Prototyping Board with multiple power and ground planes for analog and digital prototyping applications.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
VXI Prototyping Kits For RF Modules, Analog And Logic Circuits
-
• VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.
-
Product
Boundary Scan Test
-
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
Product
PXI Prototyping Module, 2-Slot, 37-Pin D-Type
40-225A-202
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 2-Slot, 15-Pin D-Type
40-225A-602
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Digital I/O And Prototyping Modules
Prototyping Module
Programmable Input Threshold and High-Side or Low-Side Drive Capability Available on Some ModulesOptically Isolated Input/Output for Interfacing to Electrically Noisy Environments Available on Some ModulesTTL Inputs and Outputs Suitable for Interfacing to External LogicOpen Collector/Drain Transistor Output Versions Suitable for Driving Internal or External Relay Coils
-
Product
COM Express Type 6 evaluation carrier board
ATX-M-CC462-T6
Carrier Board
The ATX-M-CC462-T6 is a fully featured COM Express Type 6 evaluation carrier board designed for use with the WINSYSTEMS Intel® Tiger Lake UP3 COM Express and other COM Express Type 6 modules.
-
Product
PXI Prototyping Module, 1-Slot, 50-Pin D-Type
40-225A-501
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 1-Slot, 25-Pin D-Type
40-225A-301
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
Laser Board
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Product
2-Axis High-Resolution Laser Axis Board for VME
10898D
Laser Board
The 10898D 2-axis high-resolution laser axis board provides the same resolution as the Keysight 10897D high-resolution laser axis board with increased slew rates and reduced noise. The increased stage velocity limits and low noise compared to previous laser systems offer premium positioning repeatability and accuracy for advanced applications such as IC fabrication equipment.
-
Product
Quad QSFP28/QSFP+ FMC+ Module
FPGA Board
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
Product
34945EXT Distribution Board, For One 87204x/206x Or 87606B Switch And Two N181x Switches
Y1152A
Distribution Board
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
Product
PXI Prototyping Module, 2-Slot, 9-Pin D-Type
40-225A-702
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Digital Output Board
VME-2128A
Digital Output Board
VME-2128A 128-bit High-Voltage Digital Output Board with Built-in-Test
-
Product
Extreme Rugged PC/104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM1-BT1
Single Board Computer
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
Carrier Boards
ROM-DB7500
Carrier Board
ROM-DB7500 is an Evaluation Carrier Board designed for Advantech's RISC Qseven module. It is compatible with the ROM-7420 Qseven module and provides a thorough environmentfor RISC module board evaluation. It supports wide range temperatures and 12V power input through AC/DC power adapter.
-
Product
Extreme Rugged PC/104-Plus, PCI-104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM3-BT4
Single Board Computer
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
