Protection Relay
acts as a circuit breaker in the event of a fault.
-
Product
Three-phase Protection Relay Test Set/Kit
POM2-3243
-
POM2 series protection relay test kit is the best modular designed relay tester with local control system. There are 2 models, the POM2-6143 and POM2-3243, the POM2-3243 with 3×20A and 4×300V.
-
Product
Generator Protection Relay
SEL-700G
-
Schweitzer Engineering Laboratories, Inc.
The SEL-700G is the right solution for utility and industrial generator protection, with an autosynchronizer, flexible I/O, and advanced communications. Apply the SEL-700G for comprehensive primary and backup generator protection.
-
Product
Three-Phase Protection Relay Test System
VAE-430
-
Shenzhen Feso Automation Technology Co., Ltd.
Three-Phase Protection Relay Test System with high per-phase power for electromechanical, static and numerical relays.
-
Product
6-Phase Protection Relay Tester
HME-1200
-
HAOMAI Electric Power Automation Co., LTD.
Economical 6-phase Protection Relay Tester 6-phase current (6×30A) + 6-phase voltage (6×120V) output.
-
Product
Portable Multi Phase protection relay test set with GPS
TEST-630
-
Beijing GFUVE Electronics Co.,Ltd.
Test-630 multi Phase Universal protection relay test set have 6U6I output, it is a universal protection relay tester with eight pairs of binary input and four pairs of binary output
-
Product
Single Phase Universal Protection Relay Test Set
S100A
-
S100A is the Universal Single Phase Protection Relay Test Set with 1*100A and 3*150V output, local control system for basic relay testing with manual operation.
-
Product
Protection Relay Test PW636i
PW636i
-
PW636i universal relay testing equipment is the most powerful protection relay test equipment. It can do all types of protection relay testing, from electromagnetic relays to numeral relays, microprocessor computer relays, and IEC61850 digital relays.
-
Product
Stator Ground Protection Relay
SEL-2664S
-
Schweitzer Engineering Laboratories, Inc.
Protect high-impedance grounded generators from ground faults at standstill, during startup, and while running with the multisine frequency injection and neutral overvoltage-based protection in the SEL-2664S.
-
Product
Relay Protection Test System
RELAYSTAR 1600
-
HAOMAI Electric Power Automation Co., LTD.
Relaystar-1600 the 6 phase universal relay protection test kit6-phase current (6×40A) + 6-phase voltage (6×150V) output.
-
Product
Automatic Relay Test Set
DRTS 34
-
DRTS 34 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 4 Voltage generators simultaneously available.
-
Product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix topology With Column Protection Resistors
782385-10
Terminal Block
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Sensing Resistors
Resistive Voltage Dividers
-
NGR Sensing Resistors are attached in parallel to the neutral grounding resistor. The sensing resistor allows a protective relay to detect a resistor failure in a continuous manner. Sensing Resistors are used in combination with neutral grounding resistor monitor relays. The relay measures neutral grounding resistance, neutral grounding resistor current and neutral to ground voltage. The relay continuously measures neutral grounding resistor ohmic value in an unfaulted system and it trips on if neutral grounding resistance varies from its calibrated value.
-
Product
Protection Relay Test Set/Kit
-
KINGSINE Electric Automation Co., Ltd.
Our conventional relay test set series is developed based on years of industry experience and technological accumulation, catering to various needs of power system relay testing. Renowned for its precise testing performance, user-friendly interface, and comprehensive functionality, this series has earned the trust and praise of numerous users.
-
Product
20Hz Generator
-
Signals & Systems India Private Limited
In order to implement a 100 % stator earth fault protection based on subharmonic injection, a 20Hz voltage is injected into the generator star point. The 20-Hz generator SGEN-1001 is used in combination with the Band Pass Filter SBPF-1001 in the Stator Earth fault protection. The injection can be performed by connecting the SGEN-1001 and the SBPF-1001 to the load resistor of an earthing or neutral transformer. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. From the driving voltage and the fault current, the protective relay determines the fault resistance.
-
Product
3-Phase Protection Relay Tester
HME-702
-
HAOMAI Electric Power Automation Co., LTD.
Economical 3-phase Protection Relay Testerwith 3-phase current(3×40A) + 4-phase voltage(4×120V) output.
-
Product
Digital Test Switch
FT-14D
-
Test switch solution for digital switchgear using current and voltage sensors. With the FT-14D Digital FlexitestTM switches, a new era of protection relay testing can be performed more safely, quickly and easily. The FT-14D switch allows a customer to integrate current and voltage sensors within digital switchgear and protective relays and thereby enable the Industrial Internet of Things.
-
Product
Protection Relay Testing
ARTES
-
Compact, powerful relay test systems for carrying out highly complex tests with ease and precision. The test systems of the ARTES product line are used to carry out functional tests on all types of protection devices, including DT/IDMT relays, distance protection relays and differential protection relays, to ensure that they function correctly. More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the fourth generation of ARTES test instruments.
-
Product
Universal relay test set and commissioning tool
CMC 356
-
The CMC 356 is the universal solution for testing all generations and types of protection relays. Its powerful six current sources (three-phase mode: up to 64 A / 860 VA per channel) with a great dynamic range, make the unit capable of testing even high-burden electromechanical relays with very high power demands.
-
Product
NI TB-2640B Terminal Block for NI 2532B as 1-Wire 4x128 Matrix Topology Without Column Protection Resistors
782385-01
Terminal Block
Screw Terminal, Ribbon, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors … of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.This 782385-01 card does NOT have 100 Ohm protection.
-
Product
Relay Modules
DN-PR4
-
The DN-PR4 Features a DIN-Rail mount and four form C electromechanical power relays for efficient switching of load by programmed control. The contact of each relay can control a 5 A load at 250VAC/30VDC. The relay is energized by applying a +24V voltage signal to the appropriate relay channel. Each output is equipped with a LED to display their status. Each output is equipped with a varistor that shunts the surge voltage of the inductive load or electromagnetic brake to protect the relay contact point. All relay control and relay outputs are accessible through the wiring terminals.
-
Product
Primary Current Injection Sets
-
Protective devices such as relays, overload Coils, Circuit breakers and CTS etc. must be checked regularly to ensure that they are always ready to operate correctly, Routine current injection testing will quickly detect faulty or incorrectly adjusted protection circuits / devices & will be possible to prevent serious damage to the system. Primary injection kit is designed to operate on single phase 230/240 volts AC 50 HZ to develop smooth & continuous test current as for loading, calibrating, and testing of CTS, Bimetal Relays, Protection Relays etc. The test set gives high current output at low cost and with inherent safety. The primary current injection testing checks all parts of the protection system by injecting current down the cable / bus bars. The application of the primary current injection sets is to ascertain the current carrying capacity of any Conductor, insulator, connector or calibration of CTS / Bi-metallic relays etc.
-
Product
NI TB-2643B Terminal Block for NI 2532B as 1-Wire Dual 4x64 Matrix or 2-Wire 4×64 Matrix topology With Column Protection Resistors
782385-08
Terminal Block
The TB-2643B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x64 or 1-wire dual 4x64 matrix. You can directly connect the TB-2643B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2643B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Stand-alone Three-phase Protection Relay Test Set
-
Weshine Electric Manufacturing Co., Ltd
Universal Auto Low Price 3 Phase Relay Protection Tester, 3 Channels ,40A/450VA Three-Phase Parallel 120A, 3 Channels, Each Channel ±10A/200VA
-
Product
Primary Current Injection Testers
-
Primary Current Injection Tester is designed for testing protective relay and circuit breakers and also testing the turns ratio of current transformers at high variable currents. A test current is injected into the primary side of a system to determine how the system behaves at particular levels of current. This test makes it possible to determine whether the relay will trip and how long the current needs to flow before the trip is initiated.
-
Product
Automatic Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
-
Product
Overcurrent Protection Relays
-
DKR-24 Besleme üniteleri, tüm elektrik tesislerinde 24V DC gerilim ihtiyacnkarþlamada kullanlrlar. DC besleme, genellikle acil durumlarda kullanlmaküzere aranmaktadr. Bu nedenle besleme ünitesi her an hazr durumdaolmaldr
-
Product
Overhead Enhanced Protection
-
Schweitzer Engineering Laboratories, Inc.
These products enhance distribution protection by helping relays make better tripping and reclosing decisions based on the location of a fault.
-
Product
Relay Test Set
-
Relay testing equipment is a portable apparatus designed for checking the operating characteristics of protective relays on site. Rr Relay Testing Equipments are designed to facilitate routine test or periodic maintenance test of relays by simulating (as early as possible) fault conditions under which the protective relays are required to function. There are several approaches to the method of testing relays on site. The Relay Testing Equipments are secondary injection type and are intended to be used to test the relays after isolating them from live systems, either physically or electrically.
-
Product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix Topology Without Column Protection Resistors
782385-09
Terminal Block
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Secondary Injection Relay Test Set
TD 1000 PLUS
-
TD1000+ is a protective relay test set especially designed to give the commissioning engineers a multitasking and highly reliable testing equipment. In comparison with T 1000 PLUS model, TD 1000 PLUS has two current outputs to test the differential relay characteristic curve, besides the pick-up current.
