-
product
Mining Compass
COMTA
F. W. Breithaupt & Sohn GmbH & Co.KG
*„Kassel“-type cardanic suspension device with adjustable bearings; foldable*High quality 80mm needle with adjustable inclination weight*Graduation: 1° / 1gon*High precision accuracy of ± 0,1°*Declination adjustment (± 30°)
-
product
Equipment Condition Indication
MetalSCAN
Condition indication in real-time, so you can schedule maintenance at the right time.MetalSCAN is the leading real-time, on-line condition indication technology designed to alert equipment operators to bearing and gear damage, long before equipment failure. Nothing else comes close. Its advanced capabilities deliver knowledge that transforms equipment failure to predictable and avoidable high cost events. Use MetalSCAN to optimize maintenance schedules, reduce repair costs, increase reliability and improve safety.
-
product
19" Drawer with Writing Surface, Unshielded, 10.5"H x 24"D
DR-101924-S
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
product
19" Rackmount Drawer with Keylock, Unshielded, 10.5"H x 24"D
DR-101924-K
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
product
Control Cables
TRIUMPH specializes in cable controls which are mechanical connections between controls and actuation systems used in a variety of applications. Our systems provide higher reliability, lighter weight, and greater control box selection. Current controls include wire rope, push-pull controls, sliding friction controls, ball-bearing controls and low-resistance and backlash mechanical control system cables. Wire Rope Controls: Wire Rope is used in applications where weight is critical, and the system operates in tension only. Assemblies are built to your required standards with unlimited configuration capabilities. Sliding Friction Controls: High load capacity in tension and compression. Flexible in any direction, wide temperature range and easy installation. No adjustment or lubrication needed during the life of the control. Ball Bearing Controls: Ball Bearing controls are a self-contained system that performs linear motion under tension or compression loads.Precise and accurate movement with high load capacity offering weight savings, low friction and high efficiency. Quick disconnect ends available.
-
product
Crossed Roller Rail Sets
Del-Tron’s crossed roller rail sets (or crossed roller bearings) are compact, precision rail sets that can support and guide high loads with high accuracy, excellent repeatability, and low friction. A complete range of profiles are offered with roller diameters ranging from 1.5mm up to 6 millimeters, providing load carrying capacities to 2800 lbs. For vertical applications or applications involving high acceleration or deceleration forces you may want to consider our Anti-Creep crossed roller rail sets.
-
product
Dynamic UPS
ROTOBLOC® RBT SERIES 400 - 2000 kVA
The RBT system consists of a standard synchronous generator with no special windings and a simple steel flywheel. The low speed shaft extends bearing life and reduces maintenance. The ROTABLOC® machine is very robust as critical functions do not use fragile components such as power electronics, power capacitors, electro-chemical batteries, active magnetic bearings, electro-mechanical or mechanical friction clutches.
-
product
19" Rackmount Drawer, Unshielded, 8.75"H x 20"D
DR-081920
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
product
Turbine Flowmeters
Titan’s small turbine flowmeter range use a radial flow principle based on the Pelton wheel technique. This well proven method is the ideal way of measuring low rates of flow of low viscosity liquids. For these mini flowmeters, a jet of fluid is directed at a turbine that is mounted on robust low friction sapphire bearings. The geometry of the turbine and the fluid chamber ensures that the rotational speed of the rotor is proportional to the flow rate through the device. The use of this radial arrangement allows more energy to be imparted into the turbine, so the bearing drag is far less important. Furthermore, because more energy is available the bearings themselves can be a lot stronger so increasing the life of the flowmeter. For larger flows, some of the liquid can bypass the turbine chamber, which then behaves as a “shunt” to the metered fluid. Accuracy is still maintained and the output remains linear.
-
product
High Speed Test Bench
AT444
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
product
Tabletop Mask Aligner
Model 200
The OAI Model 200 Mask Aligner is a cost-effective high performance mask Aligner that has been engineered with industry proven components that have made OAI a leader in the photolithography capital equipment industry. The Model 200 is a tableop mask Aligner that requires minimal cleanroom space. It offers an economic alternative for R&D, or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The system is capable of one micron resolution and alignment precision.
-
product
24" Rackmount Drawer with Keylock, Unshielded, 10.5"H x 30"D
DR-102430-K
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
product
24" Rackmount Drawer, Unshielded, 7"H x 24"D
DR-072424
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
product
Coordinate Measuring Machines
VideoCheck® V-HA
The most accurate multisensor coordinate measuring machine for tool measurement available in the world todayUsing 10 nm scalesAll axes are based on high precision low vibration air bearingsIntegration of additional sensor units to a multisensor system guarantees higher flexibility and measuring speedScan high precision gear profilesUse of high precision telecentric lenses in a second optical beam pathModular structure guarantees customized solutions for individual applicationsIntegrated high precision air bearing rotary
-
product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 230 x 175 mm (wxd)
CMK-06
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Flow Logger Sensor
NUL-224
This sensor allows for a stream of water to flow through its inlet and outlet pipes, thus revolving a rotation wheel within it. The wheel is not connected mechanically to anything else, but rather floats on a bearing for minimum friction and the enhancement of its minute accuracy. The measuring is done by monitoring changes in the sensor's surrounding magnetic field.
-
product
CE Marking
The CE mark enables the free movement of products into and within the European market.By placing a CE mark on a product the manufacturer is declaring, on their sole responsibility, that the product conforms to all legal requirements to achieve CE marking.Prior to placing the product on the European market, a manufacturer performs an assessment of the product against all applicable EU Directives, and verifies compliance with the relevant essential requirements.Not all products require the CE mark – only products subject to specific directives must bear the CE mark.
-
product
Upset Testing Machine
YQ/YQR Series
Jinan Testing Equipment IE Corporation
The series of upset testing machine are designed according to the International Standard 'Metallic Materials Upset Test Methods', especially for the quality inspection of high-speed rods and wires. Through simulating the quick impact conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. Under room temperature or hot conditions, exert test force in the direction of specimen axial line, quickly compress the specimen, and then the machine can inspect the metal ability of bearing upset deformation in the specified upset ratio. The upset testing machine can also show the metal’s surface disfigurements. The upset testing machine is widely used in the steel industry, standard specimen manufacturing industry, and tools manufactures for inspecting the upset tests of metallic materials.
-
product
Vision System
Project X
Project X is different. It utilises a totally new, patented technology XY scale, that records not only X and Y position but also any rotational movement of the camera system. In addition, this is an absolute scale system, which means as soon as you switch on the machine it knows exactly where it is - no need for referencing. The camera is free to glide around the measurement area mounted on a simple air bearing system, without any worry about constraining the mechanics to avoid losing accuracy.
-
product
24" Rackmount Drawer, Unshielded, 10.5"H x 20"D
DR-102420
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
product
19" Drawer with Writing Surface, Unshielded, 7"H x 24"D
DR-071924-S
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
product
Axis Play Tester
LMS 20.0 | VP 425017
Maschinenbau Haldenwang GmbH & Co. KG.
The LMS 20.0 axis play tester is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by means of counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the LMS 20.0 easy to use.
-
product
24" Rackmount Drawer, Unshielded, 8.75"H x 24"D
DR-082424-S
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
product
High-Voltage Test Hood
LX-HVE600
The bright test room with a ball-bearing cover is designed for high production quantities. Thanks to the easily exchangeable exchangeable plate, retrofitting for testing different products is also a simple task. Product properties: External dimensions (W * D * H) approx. 640 * 716 * 640mm Usable test space (W * D * H) approx. 450 * 500 * 460mm Contacting Installation space approx. 100mm high under removable plate Dielectric strength min 10kV Application area up to 2000m above sea level Pollution degree 1 without condensation Standard conformity EN50191 / EN61010-1 Schmersal safety switch AZM161 with guard locking Lid is supported by ball bearings for high number of cycles, the bearings can be easily exchanged for servicing Optionally available, Not included in the price: - Red / green signal light - Mobile substructure trolley with 19 "
-
product
24" Rackmount Drawer, Unshielded, 10.5"H X 24" D
DR-102424-S
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock.
-
product
FFT Analyzer Software Modules
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Vibration analyzer for low and middle frequencies*Calculates the spectrum of vibration acceleration*VM-FFT+ also for velocity and displacement*RMS and peak spectrum*Envelope spectrum for roller bearing analysis with VM-FFT+*Limit curve with external alarms in VM-FFT+*Power spectral density (PSD) with VM-FFT+*Two measuring cursors for magnitudes and frequencies with snap-in function*Up to four signals per window*One VM-FFT license can be operated simultaneously up to four times with different settings*VM-SCOPE may trigger the frequency analyzer module VM-FFT*External messengers *Offline measurement
-
product
Manual Fixture Kit
230355 – CMK-06
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Vibration Testers
Application for vibration tester: used for measuring periodic motion, to check the imbalance and deflecting of moving machinery.Is pecifically designed for present measuring various mechanical vibration. So as to provide the data for the quality control, run time and equipment upkeep.use the high-performance acceleration meter, realize the repetitiveness and accurate measurement. it has the function of testing axle bearing situation
-
product
Pylon ITA Mount Linear Testfixture Cassette and ITA Frame Not Included, UUT 306 x 248 mm
MG-02 VGR12
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with aluminum backpanel for a Genrad VGR12 Pylon frame• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette
-
product
20" Ball Bearing Slides Pair
DRS-20
20"D ball bearing slides ship complete with brackets and all hardware for attachment to cabinet
