Coaxial Switching
Route RF offering excellent signal repeatability and isolation.
-
product
Speed Switch
DR1000
Features • Works with remote / external pulse frequency output sensor (NPN, PNP, or Mag Pick-up) • DPDT relay output • Under-speed setpoint adjustment from 0.5-5,000 rpm (at 8 PPR) • Terminal blocks for easy wiring • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • Rugged explosion proof / NEMA 4X housing • UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
product
Sealed Switches
Haydon's sealed switches are used in commercial jets, military aircraft, military ground equipment, space applications and industrial applications with harsh environmental conditions, such as gas turbines and high temperature research instrumentation.
-
product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8491A
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
product
Dynatrol® Level Switch for Bulk Solids
CL-10DJ
The Dynatrol® CL-10DJ Vibrating Level Switch is designed for high-, intermediate- or low-point level detection of bulk solids. The CL-10DJ is typically used with bulk solids in the density range of 15-60 lbs/ft3.
-
product
1x4 Optical Switch Module
81595B
The plug-in module for Keysight's Lightwave Solution Platform 8163B, 8164B, 8166B is ideal for flexible system configuration in applications such as transceiver/receiver test with small foot-print or multiple passive component test with complex cascade.
-
product
TMR Switch Sensor Demo Board
MultiDimension Technology Co.,Ltd.
Demonstration kit for MDT omnipolar and bipolar TMR switch sensors
-
product
Switched Amplifier With Analog Detector Output
Operates at 3 GHz-10 to -5 dBm Input Power to +4 to +7 Output powerAnalog Detector OutputTTL Compatible, 70 dB On-to-Off Ratio, 50 ηSec Response Integrated RF Switch
-
product
LXI RF & Microwave Switching Solutions
Our Ethernet-controlled LXI RFIU (RF Switching Interface Units) rack-mountable signal routing solutions range from standard and user-specified relay configurations to fully integrated turnkey switching subsystems. Take a look at our Microwave Switch Design Tool to design your own switching solution.
-
product
PXI Dual 32x4 Matrix 1-Pole Switching
40-534A-021
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
-
product
Adapt-a-Switch Series
Receive unprecedented density and flexibility with the Astronics' Adapt-a-SwitchTM Series. Available for VXI, GPIB, and LAN, this series includes a wide variety of switching solutions that are field-proven for any hi-rel application.
-
product
RF Routing Switches
Quintech Electronics and Communications Inc.
RF Monitoring and Routing Switch.
-
product
Coaxial T-Switches
The benefit of a T-switch over a DPDT (or transfer) switch is that up to three combinations of RF paths are available, which is perfectly suited for space applications where more than two path combinations are required.
-
product
Flexible Data/Analog Switching System
S6025DE
Universal Switching Corporation
Designed for parallel switching of RS-232 data or other similar types of data, the S6025DE delivers compact solid-state switching in an expandable configuration. The unit can start as a smaller size and be expanded later to a full 60x60 array with 25 levels, perfect for switching RS-232 type data. It provides a choice or a combination of remote control including RS-232C, RS-422A, RS-485, GPIB (IEEE-488) and Ethernet (10base-T).
-
product
19’’ Rackmount 1/10 Gigabit Ethernet Switch
IC-SR-BOXa
The IC-SR-BOXa is based on the Interface Concept ComEth4000e Layer 2/3 1/10 Gigabit Ethernet switch into a 19’’ rack mountable box. The IC-SR-BOXa is dedicated to industrial and military networking applications.
-
product
Optical Fiber 1×13 Switch
OFSW - 1 × 13
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×13 is a 1×13 prism optical switch. It can support 1 optical fibers input and 13 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-522-M
The 40/42-860A-522-M is a PXI/PXIe dual insert/bypass switch with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
Semiconductor Switching Systems
Keithley 700 Series
The high speeds and low currents of semiconductor devices demand high quality, high performance switching of I-V and C-V signals. We offer switching solutions for both semiconductor R&D and production test applications with mainframes that can support up to 2,880 channels and a family of matrix cards designed specifically for semiconductor applications.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
Coaxial Termination, DC to 26.5 GHz
909D
The Keysight 909D is a precision, low-reflection dc to 26.5 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard.
-
product
Microwave Coaxial Cable Assemblies
MWX0 series
JUNFLON® MWX products are flexible signal transmission lines that take advantage of the remarkable properties of fluoropolymers. They are suitable for use with a wide range of frequencies up to 67 GHz. These products feature low insertion loss and low VSWR, low signal leaks and low interference due to high shielding effectiveness, and higher density wiring for use in the narrow device interiors. Junkosha provides highly reliable products for microwave /millimeterwave applications tailored to customer assembly needs.
-
product
Panel Selector Switches
Model 767S
The 767S Panel Mounting DIN sized selector switches provide convenient, reliable selection of up to 12 thermocouple or RTD (Pt100 etc) inputs. The front panel rotary switch provides easy selection and clear indication of the desired channel.
-
product
PXI Differential Fault Insertion Switch Modules
Pickering's PXI Differential Fault Insertion Switch Modules support multiple channels of two-wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to externally applied fault conditions. *Two module types are available: Two wire fault insertion module suitable for CAN Bus and FlexRay.*High bandwidth two wire fault insertion module suitable for Gigabit Ethernet, AFDX and BroadR-Reach.
-
product
Tilt Switch and Control Unit
MTS / SCU-200
Features • Detects the presence or absence of bulk material • Standard enclosure is NEMA 12 with indicator lights • NEMA 4 and Intrinsically Safe enclosures available • Rugged heliarc-welded steel probes • Use with SCU-200 for complete monitoring system
-
product
UltraCMOS SP12T RF Switch
PE42512
The PE42512 is a HaRP™ technology-enhanced absorptive SP12T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42512 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
product
High Voltage Switching Systems
HXV Series
HXV products are high voltage systems intened for Hi-pot / IR or High voltage switching. They can be configured to drive from 32 to 128 switch points per chassis and can be configured as multiplexer (1xN) or Matrix (NxM) configurations. Stand HXV chassis are used for signals up to 5000 VAC rms ( 7400 V peak ) and can carry up to 5 amps of current. Custom systems can be built up to 25KV. Most of the modules used in these systems are 1xN multiplexers or 2x4 matrix modules that can be combined to form larger multiplexers or matrices. Connector options for standard HXV include 5 way banaba jacks / binding posts, Shrouded Banana Jacks or SHV ( High voltage BNC) if you need to use a high voltage cable with a grounded shield for safety applications. Control options include 10/100BaseT Ethernet LAN, RS232, GPIB or optional manual control. Standard HXV systems use high voltage reed relays. Custom HXV systems up to 25KV use application specific relays and connectors from a variety of vendors based on required specifications.
-
product
FA Leakage Switch Mainframe
B2200A
The B2200A reduces the cost of test by enabling characterization tests to be automated, without compromising the measurement performance of the semiconductor parameter analyzer. It supports a 4-SMU, full-Kelvin configuration and a capacitance meter, with room for future expansion. Includes 14 inputs, each with a unique internal measurement path, and a distinctive capacitance measurement compensation feature for two of the inputs. Provides front panel control via keypad or optional light pen, and supports instruments such as pulse generators.
-
product
Circuit Breaker (Switch) Test Instruments
Wuhan Huatian Electric Power Automation Co., Ltd.
Circuit Breaker (Switch) Test Instruments by HVTEST
-
product
Load Switches
Analog Devices load switches provide a highly integrated solution for switching voltage rails on in a controlled manner via an internal, high-side switch. This portfolio features overcurrent and overtemperature protection and supports currents up to 3 A. They provide a very low pass element RDSON to reduce power losses. The combination of the functionality and integration levels of ADI load switches make them extremely well-suited to inrush control applications for pluggable optical modules, line side pluggable interfaces protection, power plane switching, and power rail sequencing applications.
-
product
PCIe Passive Switch
MAX4889C
High-Speed PCI Express Passive Switches Enable Gen II Switching with Low Insertion Loss and Superior Return Loss
-
product
Switch Matrices
Becker Nachrichtentechnik GmbH
The three variants of the 4X4 matrix switch (RSWM-4X4, RSWM-4X4E, BSWM-4X4) are also available as Slot-In modules compatible to our 'Modular RF Systems' construction kit. Thereby the customer is able to combine different products in a space saving and efficient way for any application.
