Solder Paste Inspection
assures volume and area of paste application.
See Also: Solder Paste, Solder Paste Measurement, 3D Solder Paste Inspection
-
Product
Vison Inspection System
-
High Speed stroboscopic 2D vision inspection system for die attached and wirebond quality in back-end semiconductor processes. User friendly HMI for easy recipe creation and management. Able to configure with various defect identification module. (Strip Mapping, Inker, Scriber, Pucher, Bristle, Laser wire cutter and Laser clip bonding cutter.)
-
Product
SparkFun Solder-able Breadboard
Mini
-
This is the Mini SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our mini modular breadboards with the same connections to pins. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
-
Product
Sensor for Filament Inspection
EyeFI
-
EVT presents the EyeFI - the sensor for the inspection of filaments. The sensor contains two cameras with an Aptina sensor and S-Mount lenses. The cameras are perpendicular to each other. It is therefore possible to inspect two sides of the filament, which means that the EyeFI can detect if the filament is out-of-roundness. Additionally the errors and defects can be detected. For example the occurring flaws are point-shaped or partly flaked, or point-shaped and transverse, or also looking like a longitudial rib, or only spots in different shapes. The defects can be detected with the EyeFI sensor. The EyeFI contains board cameras with sensors from Aptina, the IoCap and an evaluation processor. The housing is about 14x10x4 cm in size. The IoCap is the image-capture-IO-board, which is designed and developped by EVT.
-
Product
Connector, 104-Pin D-Type Female, Solder Bucket, 5A, 4-40 UNC Screwlocks
C104DFR-2SB-1A
-
This 104-pin female D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell. This connector is suitable for use with Pickering modules that use the 104-pin D-type connector.
-
Product
High Precision Angular Positioning, Calibration and Geometry INspection
LabStandard AIR
-
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.The LabStandardAIR has been designed as a “Contact Free” system and eliminates features, which may detract from achieving the optimum rotational performance. The rotating elements are supported on super high precision, air lubricated, hydrostaticbearings and are not subject to disturbances associated with gear drives.
-
Product
Micro Coax, Two Piece Contact, Receiver, PCB Vertical Mount, Solder
610140109
-
For vertical PCB terminations. Used with standard 50 and 120 Pin Micro Coax Modules.Up to 10GHz transmission speeds (PCB design dependent). Two-piece contact that allows for pin replacement, field repairable. Mates to all existing Micro Coax contacts.
-
Product
Portable Strain Gage Welding and Soldering Unit
700
-
A battery-operated capacitive discharge spot welder for attaching and wiring weldable strain gages and temperature sensors.
-
Product
Automated Optical Inspection (AOI)
TR7700 SIII
-
TR7700 SIII is the newest generation of TRI's AOI solutions, delivering precise multi-phase inspection at full speed. By combining an ultra-fast camera, intelligent auto conveyor, and new GUI, the TR7700 SIII offers a powerful and easy to use AOI solution with fast programming, optimized board loading, production line integration and support for offline programming. TRI's new color algorithm combined with multiple lighting phases increase defect coverage and help deliver highly accurate inspection results with a minimum of false calls.
-
Product
Low to Modest Volume Clean, Inspect & Test
KI-TK071A
-
1310/1550 nm & 850/1300 nm source & Autotest power meter + acceptance reporting software, inspection microscope, cleaning materials. Interchangeable MPO, MPO/APC, SC, LC connectors (EAR99 Restricted)
-
Product
Defect Inspection System
NovusEdge
-
The NovusEdge System provides high sensitivity inspection for the edge and backside of bare unpatterned wafers for current and advanced nodes. Multiple modules can be configured on the same automation platform for increased throughput while maintaining a small footprint for an improved cost of ownership.
-
Product
Bulkflow X-Ray Inspection System
-
Designed to be integrated into line with optional reject stations, the Bulkflow X-ray System is perfect for loose and free flowing products. Offering a good detection levels on a wide range of contaminants including all metal, bone, glass and dense plastics.
-
Product
Tyre Inspection Systems
-
The VLT tyre inspection system can check several tyre and wheel related items, such as tread depth and sideslip. All measurements are done very fast when the vehicle is on the roller brake tester.
-
Product
Solderability Tester
ZHX-35
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.14-2008Used to detect the self-solderability of enameled round wires and wire harness;Set variable temperature range and automatically maintain constant temperature;Under mechanical driven, samples would be withdrawn by the action of automatic insertion and lateral movement, free from vibration and noise;
-
Product
Digital Inspection
-
The DI-1000 and DI-1000L-PRO inspect fiber optic connector endfaces, providing clear sharp digital images on your Windows® PC. The DI-1000 and DI-1000L-PRO use LIGHTEL's Series 2 Tips and come with a soft case designed to fit easily into a standard laptop case.
-
Product
X-Ray Inspection System
TruView™ Cube
-
The Perfect Solution for a Powerful Small Form Factor X-ray Inspection System. The all new TruView™ Cube X-Ray Inspection System is a fully motorized radiography system developed to meet the stringent requirements of electronics assembly and component inspection. Ideal for applications where space is premium, the the TruView™ Cube X-Ray sits comfortably on your laboratory bench.
-
Product
Automatic and Accurate Inspecting Systems
Circuit AOI
-
The Circuit AOI system is designed to perform automatic and accurate inspecting systems. It integrates rigid mechanical system with advanced vision technology and manufactured and tested by strict is standards. It is suitable for circuit inspection for PCB/FPC, verification and repair. Innovation and unique inspection algorithms are applied to inspect open, short, protrusion, nick, scratch, pin hole, island, line width/space violation, object missing and others defects. AOI system can use offline setup project and check results. It will improve the throughput.Compare to halogen lighting, the full angle LED lighting of Circuit AOI can obtain the best image contrast and is good for different panel type inspection.
-
Product
WiFi Inspection Cameras
-
WiFi Inspection Cameras generates a local WiFi hotspot (without Internet access) through which video clips and still photos of hard-to-reach or hard-to-see areas or equipment captured by the probe camera can be sent to an app-enabled smartphone or tablet for viewing and sharing. Free apps for iOS devices (iPhones or iPads) and Android devices are available from the iTunes App Store and Google Play Store, respectively. The three WiFi cameras differ in probe length, camera lighting and grip style.
-
Product
Step & Repeat Non-Contact Inspection System for FPC and PCB
OHT-Ⅴ
-
*Space-saving design and highly efficient and high-speed inspection, with top and bottom slider structure*Roller head enables to handle the reverse imposition.*Easy operation by new alignment mechanism*The machine handlingPCB is called "WSR"
-
Product
Industrial CT X-Ray Inspection System
X3000
-
The X3000 is North Star Imaging’s newest standard system. Whether you are inspecting small or large components, the X3000 is the best option for customers needing a compact system with unique capabilities generally available on a larger X-ray or CT system.
-
Product
GPR System for Concrete Inspection
StructureScan™ Mini
-
Geophysical Survey Systems, Inc.
The StructureScan Mini safely locates metallic and non-metallic targets within concrete structures up to a depth of 20 inches. The system incorporates an auto target feature that marks the detection of features of interest. This function also estimates the depth of targets and automatically adjusts the depth scale.
-
Product
Mask Foreign Matter Inspection Device
PR-PD2HR
-
Efficient foreign matter inspection and measurement with high yield.
-
Product
*Micro-fluoroscopic X-ray Inspection System
Cath-X
-
The Cath-X is a bench top system employing Glenbrook’s micro-fluoroscopy technology providing highly detailed x-ray video of the critical components of the needle device. The transparent, safely shielded, view chamber permits the operator to locate the critical areas of the needle for inspection. The x-ray image can be further magnified using the electro-optical zoom feature of the Cath-X.
-
Product
Visual Counting & Inspection Systems
-
Sciotex has created a comprehensive line of visual counting and inspection systems. These systems can be custom configured for a wide range of applications and are often delivered, ready-for-installation in your environment.Our Products:PerfectCount, Ball Coleman SeedView, ConveyorView Inspection Systems, Sciotex ImageView, MultiView Inspection Systems
-
Product
Real-time X-ray Medical Device Inspection System
The Bench-X
-
Our latest real-time, compact system used for Medical Device X-ray Inspection. Very configurable and compact with high resolution at relatively low radiation levels.
-
Product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
-
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
92-960-009-M-HV
-
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - Without Backshell
-
Product
Specialist Inline Inspection
-
NDT Global treats each pipeline individually from the offset. Before a project even begins, a feasibility study of the pipeline detail is conducted by NDT Global, to determine the appropriate tool and required modifications to complete the inspection. NDT Global has an extensive engineering capability in this regard and has a proven track record in providing tailored solutions to deal with a wide variety of pipeline characteristics.
-
Product
Inspection + Cleaning for High Volume Manufacturing Environments
AVIT-2020
-
AVIT-2020 is a fully automated system that removes human subjectivity from the entire inspect-clean cycle. With integrated cleaning and fast, robotic mechanics, operators simply press the process button, allowing them to complete a week’s worth of inspections in just a couple of hours with almost zero active operation.
-
Product
Hand-held Fiber Inspection Microscopes
-
The WL-C series hand-held fiber microscopes use coaxial illumination to provide users with maximum detail. It easily can detect the finest scratches and contamination, making it ideal for critically inspecting polish quality.
-
Product
Incremental Length Gauges For Measuring Stations And Multipoint Inspection Equipment
CERTO series
-
*Interferential scanning principle*Very high system accuracy of down to ±0.03 µm*Well-matched ball-bearing guide for very high quality*Defined thermal behavior*Large measuring ranges of up to 60 mm*Interface: 11 µAPP
