Charge Sensitive Preamplifiers
See Also: Detectors
-
Product
Charge Amplifier
-
This compact Charge Amplifier has 3 signal routes.When it is used as the Charge Amplifier for the vibration analysis systemWave Stocker, all setups are possibleby the upgraded software.
-
Product
Static Charge Checker
STME-STATCHK
-
Statclean Technology (S) Pte Ltd
This is an ideal training kit for verifying and demonstrating the level of static charges generated by persons in an ESD sensitive area.It also demonstrates the effectiveness of eliminating static charges when a person is properly gounded by a wrist strap.NOTE: Product comes with 9V alkaline battery and a carrying case
-
Product
Quartz Charge Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load.
-
Product
16 Channel Charge Integrating ADC
CQ16
-
The CQ16 is a 16-channel 12bit, fast converting charge-integrating ADC for CAMAC. To provide compatibility to older CAMAC ADC’s it can be switched into an 11-bit mode. All data read-out is provided either via CAMAC commands or through the fast FERA bus on the front of the module.
-
-
Product
Capacitor Charging Power Supplies
-
Lumina Power CCPF and CCHP capacitor chargers utilize the latest innovations in power electronics to deliver clean and efficient energy for pulsed power applications. Learn more about the CCPF and CCHP below.
-
Product
Electric Vehicle Charging Station EVSE Test Adapter
FEV100
-
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope.
-
Product
Low Noise Pre-Amplifiers
-
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
Product
USB Preamplifier, 2 to 50 GHz
U7227F
Amplifier
The U7227F, 2 to 50 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
Product
30A, 100MHz High Sensitivity Current Probe
CP031A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
-
Product
Static Charge Event Detector / Data Logging System
EV-10A
-
Tokyo Electronics Trading Co., Ltd.
EV-10A detects ESD (Electro-Static Discharge) and records them in a PC. ESD sensitive electronic components increase rapidly. If electro-static charge is not strictly controlled in the production line of these components or in the assemble line using them, the yield will be decreased.
-
Product
Crossed-Roller Bearing Linear Stage 13mm Travel XYZ,Sensitivity 2um
AKSM13(A)-40
-
Model:AKSM13(A)-40 Crossed-Roller Bearing Linear Stage 13mm Travel XYZ,Sensitivity 2um Details&Spec: Please refer to KSM13(A)-40 Specification,It is combinated by 2pcs KSM13(A)-40 (C,SR,SL) and 1pc KSM13(A)-40CZ(as vertical stage)
-
Product
Low Noise Voltage Preamplifier
1201
-
The Model 1201 Voltage Preamplifier with Remote Gain Programming Option (06) is usable in both computer controlled and maual applications requiring uncompromising performance.
-
Product
Highly Sensitive Magnetization Switching Evaluation system
FMSS
-
The necessity of evaluation for media by thin film and high speed magnetic recording increases as high density of magnetic recording media. This equipment is newly-developed one which applies any time-range and pulse magnetic field to test sample, and detect magnetization after applied with highly sensitive resonating sample magnetometer.
-
Product
Preamplifier
-
Is designed for the amplification of measuring signals, e.g. weak signals of near field probes with high resolution.
-
Product
Low Noise Preamplifier
-
The UPL-3001 preamplifier is a high performance solution for the low-noise amplification of ultrasonic signals. Designed for signals ranging from 0.5 to 300 MHz, the small and lightweight, rugged unit is perfect for remote applications. This is ideal for P&C, TT, AUT or TOFD inspection.
-
Product
Crossed-Roller Bearing Linear Stage 25mm Travel,Sensitivity 2um
KSM25(A)-65
-
Model：KSM25(A)-65 Crossed-Roller Bearing Linear Stage 25mm Travel,Sensitivity 2um Details&Spec: Please refer to KSM25(A)-65 Specification,It is combinated by 2pcs KSM25(A)-65 (C,SR,SL).
-
Product
BJT Voltage Preamplifier
SIM911
-
Stanford Research Systems, Inc.
The SIM910 and SIM911 are low-noise, programmable preamplifiers which are ideal for a wide range of small signal applications. The primary differences between the two models are their input impedance and input noise.
-
Product
PCB High Sensitivity, 100mV/g, ICP® (IEPE) Accelerometer
784170-01
-
The PCB HSTA15 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB HSTA15 features a sensitivity range of 10 mV/g and requires a 4-socket plug-to-3 BNC plug cable.
-
Product
Crossed-Roller Bearing Linear Stage ,13mm Travel XYZ,Sensitivity 1um
NFP-3461
-
odel:NFP-3461 Crossed-Roller Bearing Linear Stage ,13mm Travel XYZ,Sensitivity 1um Details&Spec: Please refer to NFP-1461 Specification,It is combinated by 2pcs NFP-1461(C,SR,SL) and 1pc NFP-1461CZ(as vertical stage)
-
Product
Low Noise Current Preamplifier
SR570
-
Stanford Research Systems, Inc.
The SR570 is a low-noise current preamplifier capable of current gains as large as 1 pA/V. High gain and bandwidth, low noise, and many convenient features make the SR570 ideal for a variety of photonic, low temperature and other measurements.
-
Product
High Sensitivity Reed Relays
Series 86
-
General purpose relays - As series 80 and 88 but with coil resistances typically twice as high
-
Product
Preamplifier
-
The UBBV series are external, extremely low-noise broadband preamplifiers that can be mounted to any SPECTRAN spectrum analyzer. They are ideally suited for spectrum analyzers and oscilloscopes as well as antennas of all manufacturers and are supplied with extensive accessories.
-
Product
Programmable USB Hub with 4 Charge Ports
-
The USBHub2x4 is a programmable USB 2.0 compatible hub featuring 4 device downstream ports with standard USB type-A receptacles and each port is capable of delivering up to 2.5A simultaneously. With two host (upstream) connections using usb mini-B connectors, the USBHub2x4 is perfect for environments where multiple devices need to be shared or switched between two host computers. E.g.: software regression testing, iPhone software development and validation, Android software development and validation, USB device regression testing, manufacturing testing, device burn-in testing and USB device charge-curve testing.
-
Product
Charge Plate Monitors
-
Our charge plate monitors the voltage of the battery and the voltage of the battery.
-
Product
High Temperature Charge Mode Accelerometers
-
Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).
-
Product
Electric Vehicle AC Charging Compatibility ATS
8000
-
It is a customized system for Electric Vehicle AC Charging Compatibility testing.Hardware : Integrated by AC Source/Power Meter/DC Source/Function Generator/Scope/ EVSE CP & PD Simulator…。Software : Fully complies with SAE-J1772, CNS15511 test requirements
-
-
Product
Current Preamplifier
1641
-
The Model 1641 Current Preamplifier is a simple low cost wideband gain block for use with photomultipliers
