Courses
-
Product
Active Loop Antenna
AL-130R
-
Also known as Magnetic Loop Antenna, the AL-130R is compliant with CISPR 16-1-4. It is ideal for emissions measurements as required by various EMC standards such as FCC 18, CISPR 11, CISPR 13, CISPR 14, CISPR 32 and many more. The built-in, low-noise preamplifier, increases overall measurement sensitivity as well as the overall signal to noise ratio. As per ANSI C63.4-2014, the use of active loop antenna for compliance testing is permitted in a non-sheilded environment ONLY if the saturation indicator is continuously monitored during the course of testing. Com-Power’s Remote Antenna Interface (RAI-100) comes in very handy for this application. It is a compact controller which can be used to enable/ disable RF measurement circuit and monitor saturation and battery low conditions remotely via a fiber optic cable up to 30 mtrs in length.
-
Product
Decoders
SignalPilot
-
Electronic Solutions ULM GmbH & Co. KG
Today we would like to present to you a brand new multi-protocol accessory decoder designed for controlling signals. Due to its intelligent software it supports DCC and Motorola®. Flexible programming makes this decoder THE all-rounder amongst accessory decoders. The SignalPilot has 16 outputs for direct connection of micro lamps respectively LEDs installed in daylight signals. Due to the fact that the outputs are designed as push/pull power amplifiers, they are suitable for both – conventional daylight signals with common anode as well as for daylight signals and/or lighting strips with common ground (common cathode), as is the case with some Viessmann® signals. Of course, the SignalPilot decoder can also handle semaphore signals and turnout motors.
-
Product
Automatic Total Nitrogen/Phosphorus Monitoring
TPNA-500
-
More than 10 years have passed since the 5th Water Use Regulation was enforced in 2001. From the perspective on preservation of ambient water quality, it has become a matter of course for companies to be compliant with regulations and observe corporate compliance. Total nitrogen and total phosphorus monitoring in the future has the potential to lead to proactive enhancement of corporate value, in addition to compliance with regulations. While we propose technological innovations and improvements and LCC*1 reductions, we will pursue the future where regulations are strictly observed and corporate value is improved through monitoring.
-
Product
Mining and Geochemistry Handheld XRF Analyzer
-
DELTA Mining & Geochemistry Handheld XRF Analyzers provide immediate results to help determine the next course of action for the entire process - exploration, ore grade/process control, environmental sustainability. On-site detection of metals, minerals & contaminants. GPS-GIS-XRF for instant metal mapping, time, cost savings
-
Product
Circuit Break Timer Test Set
PME-500-TR
-
Before developing the system or equipment for the testing of a circuit break timer for distribution, the application information was obtained by consulting various users of this type of timer for circuit breaker. The customers consulted were from private service and maintenance companies, large industries, and of course from the Utility companies. It is essential to receive first hand information of the actual requirements and needs of each of these customers who are making these types of tests and then make a detailed study of the various alternatives offered by different manufactures of this type of circuit breaker timer.
-
Product
Check Weighing
-
You run containers all day (and sometimes all night) at light speed. Of course there are minor mistakes or issues from time to time. If you know there is an issue or even if you aren’t sure, let FlexXray do a weight inspection for you. We’ll identify any abnormalities and help you address them quickly and efficiently.
-
Product
Safety Compliance Test System
EN 60601
-
Test system for electrical safety compliance testing of medical products in accordance with EN 60601-1, 3rd edition.The system is equipped with three test fixtures which are connected in parallel order to reduce the number of setup tasks for different variants in the course of day-to-day manufacturing processes. Its purpose is to test medical products, e. g. patient monitors, which are employed at hospitals to monitor heartbeat and oxygen saturation.Based on the integrated electrical safety tester by Associated Research, in combination with an AC power source and a switching matrix, it is possible to fully automate tests like for instance AC/DC high-voltage tests, insulation resistance measurements, earth connection tests and leakage current measurements.The required occupational safety is provided by a high-voltage safety hood in accordance with EN 501191. The entire safety technology, as well as the control PC, is mounted in an aluminum-profile cart.
-
Product
Intrinsically Safe Smartphone for Mining Locations
Smart-Ex 01M
-
The new Smart-Ex 01M was developed and certified to be used in underground mining locations - one of the toughest workplaces in the world. This rough environment places extra importance on mobile workers equipment to help them complete their work while staying safe - the Smart-Ex 01M is the perfect device to withstand this adversity. With this advanced technology, everything which was once handled by paper, clipboards and huge staff costs causing delays, can now be handled by this intrinsically safe smartphone. The Smart-Ex 01M comes with the same and unrivalled features as the Zone 1 / Division 1 Smartphone, the Smart-Ex 01: Same performances, same features, same quality. Of course, it is also unlocked, can be used with dirty or wet work gloves and has a powerful battery for a long workday. However, it is important to know that the Smart-Ex 01M is a stand-alone device with an own mining certification. Therefore and because of certification reasons a yellow leather case is required in underground mining locations. The Smart-Ex 01M with an ambient temperature range from 0C to +50C is approved and certified for use in ATEX and IECEx Mining areas.
-
Product
Inspection Cameras
-
The inspection camera opens a new view into the insides of machines and systems; whether an endoscope, thermal imaging camera or infrared thermometer - an inspection camera is the ideal instrument for monitoring and maintenance.Due to the flexible control of the endoscope or the visual display of potential damage areas in machines or systems, weaknesses and points of failure can be detected and therefore be prevented. The inspection camera make this possible without the need for complex disassembly.The inspection camera is used by electricians, safety experts, expert witnesses, mechatronics, and mechanics. The inspection camera is also used for apprenticeships and in-service training. An inspection camera can be applied internally as well as at school or at universities for demonstration purposes. With their help, inspections in the industrial sector can be organized considerably faster, more targeted and more cost-efficient. An inspection camera is an important companion in the course of everyday work.
-
Product
Fourier Transform Infrared Spectrophotometer
IRTracer-100
-
This system achieves excellent sensitivity with an SN ratio of 60,000:1, high resolution at 0.25 cm-1, and high-speed scanning capable of 20 spectra/second. The performance of medium and higher end models is supported by high reliability including advanced dynamic alignment and an interferometer with a dehumidifier. This is compatible with applications active in a variety of circumstances, with a library of approximately 12,000 spectra and data analysis programs for contaminant analysis, and time course and rapid scan programs for reaction tracking.
-
Product
Training Kits
-
Keysight offers a variety of Training Kits designed to assist educators in quickly setting up new engineering courses and labs on topics ranging from the Internet of Things (IoT), RF circuit design, precision power measurement, and more. These training kits will provide you with ready-to-teach material for a full semester, covering 50 hours of lab sessions. Courseware integrates hands-on industry relevant experiences, and real-world applications.
-
Product
Photometer
Optronik Line DSP 200
-
Instrument Systems Optische Messtechnik GmbH
DSP 200 offers outstanding sensitivity and stability for precise measurements even at very low illumination levels. The instrument meets, of course, all requirements of the newest standards, like EN 13032-1 and DIN 5032-7 (2017). A low-noise photo diode with V(lambda)-filtering and optimized electronics provides for a broad dynamic range from 0.1 mlx to 200 klx. At the same time the very high local resolution allows an accurate determination even of high gradients when measuring headlamps. Therefore, the DSP 200 is suitable for all automotive and traffic applications, as well as for flashlights and for measurements of all pulse width modulated light sources.
-
Product
Shaker Control Complex
K-5201
-
n the course of vibration tests of finished products or prototypes, a number of steps are carried out that require certain, often very complex, algorithms for the operation of bench equipment and the processing of measurement results. Automation of the test process allows to reduce time costs, improve the accuracy of the task, the reliability of measurements, the visibility of information and minimize the impact of the human factor.
-
Product
Speaker/Receiver Unit Tester
BK2120A
-
Our new, upgraded BK2120A is a complete system for testing both acoustical features and rub & buzz in microspeakers, receivers and earphones or earbuds. It is just as fast and easy to use as our "Classic" BK2120A speaker tester, but because it connects with a LAN cable, you can use it with a notebook, as well as a PC. Its new modular design also makes maintenance more convenient and the redesigned BS1123 software is even easier to use and more versitile than the old version. You still get both graphical and numeric test data but with more display options than before. We still customize our machine to your special needs and of course you can still save your data to analyze later. Easier setup, improved design, more features, easier to use: we expect our new BK2120A to be even more popular than the original!
-
Product
Ultrasonic Transducers
-
Low frequency transducers for ultrasonic testing of concrete and other course grained materials. Shear Wave transducers (pictured above) are used in combination with compressional wave transducers to calculate Poisson's Ratio. The line of general-purpose compressional wave transducers feature robust PZT elements in stainless steel.
-
Product
Elevators Diagnostics System
Vector
-
Lift diagnostics system “Vector” is used for measurements in the course of elevators diagnostics and enables measurements of the following parameters:
-
Product
Course Length Tester
TF124
-
TESTEX Testing Equipment Systems Ltd.
Course Length Tester, to determine the accurate length of a complete course of knitted fabric. When the yarn is attached to the clamp and wound round the pulleys, the length indicated on the ruler by the weighted clamp is added to that indicated on the appropriate location in use to give the total length of yarn.
-
Product
Fluid Power Actuators
HPU
-
Hydraulic power units (HPU’s) complement our extensive offering of rotary and linear actuators. We have over three decades of experience in their manufacture with units in service in a variety of plants and pipelines in locations spanning the globe. Although our HPU’s are primarily intended to power our hydraulic actuators they are of course suitable for other applications as well. And, in order to provide a complete range of options to best meet the requirements of any application, RFS also has the Skilmatic range of self-contained electro-hydraulic actuators.
