Impulse Voltage
-
product
High Voltage D/A Converters (>=20V)
Analog Devices’ offering of digital-to-analog converters with on-chip high voltage output amplifiers includes the AD5501/AD5504, which are single-channel/quad-channel products with a DAC output range of 0 V to 30 V or 0 V to 60 V. The AD5535 is a 32-channel DAC with output range of 0 V to 50 V or 0 V to 200 V.
-
product
Multifunction Voltage and Current Calibrator
MC140i
Multifunction calibrator MC140i is ideal for calibration of voltmeters, ammeters, DMMs and panel meters. AC/DC voltage 1uV to 1000V. Current 50uA? to 1000A using test coil. Deviation control along readout. 0.0035% basic dc accuracy. 0.03% basic ac accuracy. Supplied with RS232 interfaces. UKAS/NIST Traceable
-
product
Contact Voltage Detectors
Shanghai Beha Electronics Co., Ltd.
The detector detects a high and extra high voltage in AC lines. An elongate insulation rod permits checking of high voltage circuits at safe distance for voltage.
-
product
Voltage And Continuity Testers
Unlike voltage testers, continuity testers are always used when a circuit is turned off—or on wiring or devices that are disconnected from the circuit. They don't test for the presence of voltage but rather to see whether an electrical path is intact in an appliance or a device.
-
product
Two-Pole Voltage Tester
P-6
SONEL P-6 has all the features that characterize the P-4 Voltage Tester and P-5 Voltage Tester. In addition, the P-6 model has the phase identification function which allows to verify the phase compatibility (and its overtaking or delay) against the phase at the reference object.
-
product
AC Voltage Proving Units
HLV-2
Standard Electric Works Co., Ltd
The AC Voltage Detectors and AC Voltage Testers utilized to determine if the devices under test are functionally working. They are not a calibrator and cannot be utilized for calibration.
-
product
Linear Voltage Regulators
ST offers a wide range of voltage regulators intended for automotive applications.
-
product
Cross Voltage Testers
designed to perform the 60 Hz power line cross test/AC power fault tests required in GR 1089 issue 6 table 4.5 surge test 3,4, 4.3,and 6, and for UL 1950 section 6.4 paragraph 3 and 4.. Preset and Adjustable Time Settings Measuring Terminals including Voltage Sense and Current Shunt portals provide a safe location for users to accurately measure test voltages and output current while setting up tests. Calibration of the Mini_PT-600 is designed to be performed with a simple handheld multi-meter and the removable Currents Shunts can be easily sent to a calibration laboratory if required.
-
-
product
AC/DC Voltage Detector (CONTACT TYPE)
LVD-20
Standard Electric Works Co., Ltd
Contact type. LED indication and audible alarm sound when voltage is present. Designed for AC/DC voltage detection. Used for bare wires or conductors. Self-test function. For indoor use only. Low power consumption. Light weight and compact.
-
product
Voltage Logger0 to 25V DC
TV-4704
The TV-4704 measures voltage from 0 to 25V DC and can be connected to a variety of industry standard sensors enabling the logging of a wide range of process parameters.
-
product
Selenium Voltage Doubler Rectifier P/N 6063C
Selenium Voltage Doubler Rectifier, P/N 6063CPlate size: 1.6” x 1.6”Each plate is rated for 33 Volts, 9 AmpsNumber of plates: 24
-
product
PXI 10 Channel High Voltage Attenuator
41-660-001
The 41-660 and 41-661 are high voltage attenuators designed to reduce the high output voltages commonly generated by some types of sensors. This is in order to produce manageable signal levels that can be acquired by typical data acquisition devices in a PXI system.
-
product
Voltage Converter
99539C
The model 99539C is an 8 channel wide dynamic range voltage to frequency converter of modular design.
-
product
Isolated Voltage Source
SIM928
Stanford Research Systems, Inc.
The SIM928 Isolated Voltage Source is ideal for applications where ultra-clean DC voltage is required. Voltage can be set between ±20 VDC with millivolt resolution, and the source can drive up to ±10 mA
-
product
Continuity of Insulation Tester (Low Voltage Method)
DYQ-005
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-5;Inspection standard: JB/T4279.12-2008Used to test the film continuity (namely the pinhole number of enamelled wire sample per unit length) of enameled round wires with nominal conductor diameter of0.050mmand below;The application of advanced SCM control allows for faster operation and stronger anti-interference capacity.
-
product
Cycle Voltage Drop (Rise) Simulator
STT-CSS-20P1
Beijing KeHuan Century EMC Technology Co,.LTD
*Using 2 The regulator, and the rated voltage adjustable automatic voltage regulator, power fluctuations avoid adversely affecting the test results. Simulate the test under 110V power supply. It can simulate the fluctuation of the power grid under extreme conditions (such as high or low power supply voltage in remote areas).
-
product
Shaft Voltage Tester™ Digital Oscilloscope
AEGIS®
Digital Oscilloscope and Multimeter with Conductive Microfiber Probe Tips. Is your motor safe from destructive shaft voltages? For the first time you can get all of the tools to find out in one place. The AEGIS® Shaft Voltage Tester™ Digital Oscilloscope bundle includes the AEGIS-OSC-9100 100 MHz digital osciloscope, shaft voltage probe tips, and a shaft grounding simulator. Armed with these tools, you can quickly and easily find whether your motors are at risk of premature bearing failure due to VFD-produced bearing currents.
-
product
Single Channel High Voltage Linear Amplifier
F20A
The F20A is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of ±150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Dual Channel High Voltage Linear Amplifier
A400D
This unit contains two independent A400 amplifiers that share common ground reference and power supply.
-
product
Probe Oscilloscope High Voltage
High voltage probes allow safe and accurate voltage measurement using your oscilloscope.
-
product
AC & DC Combined Test Set With / Without Impulse
This testing equipment is used in electrical and power industry.
-
product
Three Phase AC Voltage Source
EAC-TAVS
Electronic Test & Power Systems
The EAC-TAVS is a series of programmable high power AC voltage sources. Each system provides a three phase true sinewave output as standard. Each unit is built in a freestanding cabinet. The output frequency is adjustable in the range of 45 - 105Hz. Different frequency ranges are optional, with up to 805Hz possible. An RS-232 and CAN interface are provided as standard. The high resolution TFT front panel displays a host of measurement and setting functions. Besides standard models, other nominal power levels and voltages can be user specified. Single phase and bidirectional versions are available on request.
-
product
LXI High Voltage Matrix
65-218-121-CC
The 65-218-121-CC is a plug-in module is part of a scalable high voltage matrix platform designed to provide a large matrix solution with a switching capacity of 1000V without access to the chassis backplane.
-
product
DC High Voltage Test Set
It is extensively used in electrical and power generation industry for varied testing operations.
-
product
Voltage Detector
Shenzhen Noyafa Electronic CO.,LTD
*Detect AC Power range : 50-1000V.*Test live wire and with flash indicate.*Locate wire break point easily.*LED assist using in dark place.*Certification. Passes RoHS, FCC, and CE compliance testing, and Noyafa is certified to the ISO 9001 standard.*100% Affordable. Manufactured in China and a lot cheaper than competitor products with similar quality.
-
product
PXI 12 Channel High Voltage Multiplexer
40-320-001
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
Stand Alone Low Voltage Tester
TestMate 128
The TestMate continuity tester features a universal interface fixture that accommodates adapter cards for quick changes in harness setups. Adapters can be exchanged in seconds to adapt quickly to any of a variety of wire-harness/cable connectors.
-
product
High Power/Anti-Surge/High-Voltage Resistors
ERJ-P Series
Panasonic Industrial Devices Sales Company of America
Panasonic’s ERJ-P Series High Power Resistors offer the ability to use smaller case sizes while still maintaining the same level of power or better in respect to conventional size Thick Film Resistors. The ERJ-P Series has a unique trimming pattern and high heat dissipation characteristics. These parts can be easily designed as replacements for existing Thick Film Resistors due to comparable technology and materials with use of better manufacturing processes. The ERJ-P Series has an operating temperature of -55°C to 155°C, with a smaller part, you have a higher solder-joint reliability. Less material means less solder which lowers risk for solder fracture due to thermal expansion or contraction. Panasonic High Power Resistors are AEC-Q200 Qualified.
-
product
Broad-Range High Voltage Non-Contact Tester
HVNCVT-2
Use to check for the presence of voltage in overhead conductors or to find faults in cables.7 sensitivity ranges up to 230kV AC (240V, 4.2kV, 15kV, 25kV, 35kV, 69kV, 115kV, 230kV).Audible and visual signals indicate the presence of voltage.Water resistant.Includes durable carrying case and universal/shotgun adapter.
