Parallel Interface
Connection between devices transmitting information through multiple conductors simultaneously.
See Also: Interfaces, Serial Interfaces, Bus Interfaces, UI, MIPI, Interface Adapters
-
Product
Ethernet Parallel Interface
Model 8003
-
* Provides 40 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has vertical Ethernet and Digital IO connector on the component side. * Optional Relay Driver board adds 4, 32 or 40 Relay Drivers. • Apply regulated 5 Vdc power through the Digital IO connector.
-
Product
Serial Parallel Interface
Model 2313
-
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
Product
Ethernet Parallel Interface
Model 8013
-
* Provides 128 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side. * Mates to Relay Driver Boards with 64 or 128 Relay Drivers.* Mates to 115650 Connector Board with 4 flat ribbon headers.
-
Product
Serial Parallel Interface
Model 2303
-
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
Product
Ethernet To Parallel Digital Interface Boards
-
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
Product
GPIB Parallel Interface
Model 4823B
-
* Provides 56 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Available with DIN connector on circuit side for piggyback mounting.
-
Product
Ethernet Parallel Interface
Model 8113
-
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
Product
Parallel Interface Voltage Output D/A Converters
-
Analog Devices offers a large portfolio of parallel interface voltage output D/A converters (DACs). We provide precision, fast settling, rail-to-rail micropower VOUT D/A converters, with resolutions of 8 bits up to 16 bits, single-channel to 40-channel density, and a unipolar or bipolar supply. These devices are used in a wide variety of applications such as process control, automotive test equipment, or digital gain and offset adjustment.
-
Product
GPIB Parallel Interface
Model 4803
-
* 4803 Board provides 40 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual GPIB headers support connections to a GPIB Connector/Address Switch Assembly or to a GPIB Flat Ribbon Cable Assembly.* Optional Relay Driver board drives 24-40 relays.
-
Product
GPIB to Parallel Printer Interface
Model 4892B
-
* Adds a GPIB Interface to Printers with Centronics or IEEE-1284 parallel interfaces. See the compatible printer list. * Replaces obsolete printers and plotters with a current HPGL/PCL5 printer.* Prints and Plots from most Analyzers. * Large 256 kbyte buffer and high speed GPIB interface off-loads the instrument and reduces printing time.* No program changes required.* Rack mountable in 1 U high rack mount kit.* Includes universal VAC Power Adapter and printer cable.
-
Product
PXI LIN Interface Module
Interface
The PXI LIN Interface Module is a bus interface for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LIN Description File (LDF) databases in integrated LIN databases. PXI LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
PXI CANopen Interface Module
Interface
The PXI CANopen Interface Module is a high-speed CANopen interface for developing applications with the NI-Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. The PXI CANopen Interface Module can transmit/receive PDOs and SDOs according to CiA DS301. It also features a batch SDO editor with electronic data sheet (EDS) file integration and layer setting services (LSS) support for slave node configuration.
-
Product
Interface (PMC)
QPM-1553-TB
Interface
The QPM-1553-TB provides the highest level of performance, flexibility and interface density for MIL-STD-1553A/B via PMC (PCI Mezzanine Card) to Thunderbolt 3 device. The QPM-1553-TB is integrated with powerful software that reduces development time. All 1553 databus functionality is supported from our advanced API (Application Programming Interface).
-
Product
Interface
RAR-PCIE
Interface
Available in a range of configurations to match your needs, RAR-PCIE provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols.
-
Product
ARINC interface
RAR-EC
Interface
Available in a range of configurations to match your needs, the 11 channel RAR-EC provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols, for an ExpressCard interface. The RAR-EC supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, time-tagging, error detection and four avionics-level I/O discretes.
-
Product
Interface
RAR15XF-TB
Interface
On-board firmware, large data buffers, and a high-level API are integrated to provide total flexibility in monitoring and generating ARINC bus traffic. Simultaneous scheduled and burst mode (FIFO) messaging is supported on all ARINC 429 transmit channels. Each ARINC 429 receive channel provides simultaneous dedicated and buffered mode storage, along with label/SDI filtering.
-
Product
PXI Interface Module, AIT MIL-STD 1553
M3406A
Interface
Interface to the LRU in avionics test solution Up to four channel MIL-STD-1553 bus interface with full error injection and detection Concurrent Bus Controller, multiple Remote Terminals (31), and Bus Monitor operation capabilities Data capture filtering, 100% bus recording, and physical bus replay Variable output voltage signal and software selectable bus coupling modes 10 high voltage (up to 30 V) programmable DIO lines PXI trigger generation on 1553 bus events
-
Product
High Performance PCI-GPIB Interface Card
82350C
Interface
Support fast transfer speeds for high data throughput and easily attach to low-profile PCs.
-
Product
Interface
P-SER
Interface
P-SER I/O product is a native PMC form factor interface providing real-time serial input and output with high time-precision reception/input time-stamping, scheduled transmission/output, event triggering and interrupt support. This interface is designed to meet the needs of both the simulations/test and the real-time embedded applications whether in Windows or VxWorks environments.
-
Product
Low-profile High-Performance IEEE488 GPIB Interface for PCIe Bus
LPCIe-3488A
Interface
The IEEE-488 standard, also known as GPIB, is a bus interface that connects instruments with a computer to form an ATE system. Today, GPIB is still the most popular interface between computer and instruments. ADLINK"s USB-3488A, LPCI-3488A and LPCIe-3488A controller interface cards are fully compatible with the IEEE-488.2 instrumentation control and communication standard and are capable of controlling up to 14 stand-alone instruments via IEEE-488 cables. The USB-3488A, LPCI-3488A and LPCIe-3488A are designed to meet the requirements of high performance and maximum programming portability.
-
Product
Interface
RAR-XMC
Interface
Designed for embedded, laboratory and simulator applications, the RAR-XMC supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, receive message time-tagging and error detection, and IRIG-B receiver (AM or DC/TTL) and generator (DC/TTL).
-
Product
Interface
RCNIC-A2PA
Interface
The RCNIC platform is a high performance PMC module for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
Smart Aircraft Interface Devices
webCS
Interface
The Ballard webCS® is the first highly integrated smart AID/server/router that securely bridges avionics data with wired and wireless networks in a single compact box. This wireless aircraft communications server platform is simple to install and configure, safe to interface with aircraft domains, and provides highly secure data transfer. The compact, versatile webCS enables aircraft operators to easily gather and process aircraft data, and then route it to where it is needed—whether on or off the aircraft.
-
Product
Vehicle Multiprotocol Interface Module
C Series
Interface
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787458-01
Interface
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
Product
GPIB Parallel Interface
Model 4813
-
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Optional Relay Driver boards add 64 or 128 Relay Drivers.
-
Product
C Series PROFINET Interface Module
Interface Module
The C Series PROFINET Interface Module provides two PROFINET interface ports that enable you to reliably connect programmable logic controllers (PLCs), I/O, sensors, and drives over long distances in industrial environments. PROFINET is an application protocol that uses familiar concepts from PROFIBUS that are implemented on the physical layer of Ethernet. The C Series PROFINET Interface Module includes NI-PROFINET driver software for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces.
-
Product
4-Port MIPI Interface GMSL Video Capture Card
MIC-FG-4G
Interface
GMSL SerDes controller. Supports up to 4K, 30fps, quad channel. MIPI 4 Lane compliant. Power Over Coax. V4l2, Gstreamer, Python support on Linux.
-
Product
Power Interface and Prototype PXI Card
GX7404
Interface
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
Product
PXIe Remote Control Interface Module
43-921-002
Interface
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
