PMC Carriers
-
Product
PMC Card
P-DIS
-
The P-DIS PMC card is different from most currently available data acquisition boards. It provides multiple I/O types on a single module and the functionality to work with high-speed digital I/O signaling. With very accurate time stamping of input data and synchronization to an external IRIG-B source, the P-DIS provides the capability to precisely synchronize all output ports.
-
Product
PMC Compatible Wizard Interface
PMC-Wizard
-
The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems. The primary application is to provide very high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 Ω. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media, and the noise coupling to the environment
-
Product
SIMRC - Carrier Kit
1050-002
-
The SIM Relay Carrier 1050 simplifies the custom integration of small format embedded switching cards. No additional PCB design is necessary. Due to the Eurocard format the carrier can be fitted into a standard case or can be mounted in a 19" rack with side rails. Plug in standard SIM Relay Cards and control your switch application with the provided Soft Front Panel without any additional programming.
-
Product
Modular VXI Switch Card Carrier
1260-100
-
The 1260-100 Switch Carrier accommodates up to six plug-in switch cards, providing optimum switching solutions while reducing the ATE size requirements.
-
Product
1 Or 2 Stream MIL-STD-1553 PMC Test And Simulation Modules With Prog. Coupling,onboard Bus Network And Variable Output Amplitude
AMCX1553-xT
-
MIL-STD-1553 Test and Simulation modules for PMC with 1 or 2 Dual Redundant streams plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
PCIe Carrier Board for SOM3
Solar Express 215 (SE215)
-
Sundance Multiprocessor Technology Ltd.
SE215 is a development board for Sundance SOM3 . It is a PCIe X1 Gen2 carrier card with one site for an SOM3. It offers USB JTAG and UART, through a micro USB connector, Display port and comes with a version of Display port IP core for SOM3 from Bitec DSP. The card provides Power GOOD and user LEDs for rapid debugging.
-
Product
Interface Module for Multimode, Multiprotocol Excalibur 8000 Family of Carrier Boards, a Complete Solution for Developing & Testing 1553 Interfaces
M8K1553Px(S)
-
The M8K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M8K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M8K1553PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M8K1553PxS module is NOT compatible to the M4K1553MCH module.The M8K1553Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
-
Product
Carrier Boards
ROM-DB3900
-
ROM-DB3900 is an evaluation carrier board designed for the Advantech RTX2.0 module. It is compatible with the RTX2.0 module ROM-3420 and has a rich I/O interface for evaluation and development. It supports wide range operating temperature, and also supports two MIPI connectors for a camera module. ROM-DB3900 is an ideal development board for ruggedized applications, such as industrial control, automation control and HDMI systems.
-
Product
3U VPX PMC/XMC Carrier Board
IC-CMC-VPX3b
-
The IC-CMC-VPX3b is a carrier board designed to expand 3U VPX system capabilities with the integration of PMC/XMC mezzanines.
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 4 M.2 PCIe SSD Modules
SKU-086-B4
-
B-series PCI Express Gen3 Carrier board was designed as a cost-effective storage solution for the systems that are using a motherboard with PCI Express bifurcation support. Such motherboards can be configured in the BIOS to split x16 PCI interface to four PCI Express interfaces by utilizing the following PCIe lanes:- x4 PCI Express interface 1: lanes 0,1,2,3 from x16 PCIe interface;- x4 PCI Express interface 2: lanes 4,5,6,7 from x16 PCIe interface;- x4 PCI Express interface 3: lanes 8,9,10,11 from x16 PCIe interface;- x4 PCI Express interface 4: lanes 12,13, 14, 15, from x16 PCIe interface;
-
Product
PMC to PCI Express Adapter w/ TSI384
6083
-
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI express primary side and a PCI/PCI-X secondary side.
-
Product
PCI Express FMC Carriers
-
Sundance Multiprocessor Technology Ltd.
FMC carrier boards based on the PCI express format:
-
Product
3U CompactPCI Serial Front Removable SATA Carrier for SSDs
SD8-STEEL
-
The SD8-STEEL is a peripheral slot card for CompactPCI® Serial systems. It includes a shuttle for 1.8 or 2.5” SSD or HDD drives. Signal integrity is optimized with 6Gbps SATA drivers. A push button ejection of the drive enables easy swap removal.
-
-
Product
PXI Carrier Module For SwitchBlock
-
The PXI Carrier Module for SwitchBlock can hold up to six Matrix Modules for SwitchBlock while occupying four PXI slots. By connecting multiple SwitchBlock relay cards through the carrier's integrated analog bus, you can easily create large matrices with more than 2,000 crosspoints in four PXI slots and more than 8,000 crosspoints in a single PXI chassis. Each Matrix Module for SwitchBlock comes in an A-type version, which serves as the first matrix building block and offers row and column access through the front connector, and a B-type version, which serves as an expansion module and only provides column access through the front connector. Typically, SwitchBlock systems contain one A-type module and numerous B-type modules.
-
Product
3U Format CompactPCI (CPCI) Bus IP Carrier
CPCI-SIP-2
-
The CPCI-SIP is a 3U format CompactPCI (CPCI) bus IP carrier. The CPCI-SIP-2 provides mechanical support and the electrical interfaces for two single width IP modules, or a double width IP module. Multiple CPCI-SIP-2 boards may be installed in a single system.
-
Product
PCIe FPGA Carrier For FMC+, Kintex UltraScale™
PCI592
-
The PCI592 is based on the Xilinx XCKU115 Kintex UltraScale FPGA, which provides 5,520 DSP slices, 75.9 Mb RAM and 1,451,000 logic cells. The FPGA interfaces directly to the FMC+ DP-23 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR4 memory channels (2x 64-bit wide and 1x 32-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10G/40G, SRIO, PCIe) without the need to go through the host.
-
Product
PCI - Quad Industry Pack Carrier w/ DSP
PCI-4IPM
-
The PCI-4IPM module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the PCI-4IPM is the perfect solution.The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via thePCI bus. WinNT drivers are standard.
-
Product
PMC to PCI Express Adapter w/ TSI384
8636
-
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI Express primary side and a PCI/PCI-X secondary side.
-
Product
3U VPX Flash Storage Module Carrier
FSM-C
-
Curtiss-Wright Defense Solutions
The Flash Storage Module Carrier (FSM-C) provides rugged, removable, VITA 48.2 compliant, solid state storage in a 1” pitch, industry standard 3U VPX format. By providing a COTS storage solution, the FSM-C can lower schedule and technical risk for embedded storage applications.
-
Product
M-Module Carrier for PCIbus
i2001
-
The i2001 M-module Carrier for PCI bus implements a PCI bus gateway to the M-module interface. One M-module mounting socket is provided by this carrier. The M-module I/O connector is accessible through the PCI card bracket. The M-module interface of the i2001 complies to the M-module Specification ANSI/VITA 12-1996. The interface features A8, A24, D16 and D32 access types.
-
Product
OnyxFX Virtex-7 Processor and FMC Carrier - 3U VPX
Model 5973
-
- VITA-57.1 FMC site offers access to a wide range of possible I/O- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe4 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- LVDS connections to the Virtex-7 FPGA for custom I/O- Optional optical interface for backplane gigabit serial interboard communication- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
Carrier Cards and Bus Adapters
-
Abaco's wide range of carrier cards allows you to expand your systems capabilities simply and cost-effectively, allowing easier technology insertion.
-
Product
PMC ARINC 429 Board
MS 1723
-
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- Spartan-3AN FPGA and Arinc429 controller based design- 8 transmit and 8 receive independent channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
AngelShark Carrier Board™ Mac Pro (Late 2013) Cylinder Storage Upgrade by M.2 PCIe SSD
SKU-088-01
-
How to upgrade storage capacity (the SSD) on a Mac Pro (Late 2013) cylinder?It is possible with the AngelShark Carrier board™ (designed & produced by Amfeltec Corporation, Canada).Carrier board is located internally between the Mac and the original SSD module. It supports any M.2 PCI Express (M-key) SSD modules with standard lengths 2280 and 2260, 22110 (optional).Carrier Board supports x4 PCI Express Gen 3 connection on each M.2 circuit, and it is compliant with PCI Express Specification 3.0 and M.2 Specification 1.1.
-
Product
3U 4HP PMC Adapter for cPCI
cPCIBPMC3U32
-
cPCIBPMC3U32 is a 3U 4HP PMC adapter for cPCI. One PMC position is provided with a 32 bit interface for both the PMC and the cPCI backplane. User programmable VIO on the PMC side of the bridge. High capacity mini-planes with filtering for 3.3 and 5V.
-
Product
DDC (Dual DIMM Carrier) DIOS Adaptor
JT 2702/DDC
-
The JT2702 Digital 256 channel JTAG I/O module. JT2702/DDC (Dual DIMM Carrier) is a DIMM DIOS accessory product. It is typically used in custom test adapters or fixtures where a large number of digital I/O channels are required with a minimum space overhead.
-
Product
PCIe Gen 3 ATCA Carrier With Low-Power Xeon E3
ATC123
-
The ATC123 is a Carrier Module with an onboard x16 PCIe Gen3 slot (only x8 PCIe is routed to the slot) to accept any standard PCIe edge type module.
-
Product
SparkFun MicroMod Machine Learning Carrier Board
-
The MicroMod Machine Learning Carrier Board combines some of the features of our SparkFun Edge Board and SparkFun Artemis boards, but allows you the freedom to explore with any processor in the MicroMod lineup without the need for a central computer or web connection. Voice recognition, always-on voice commands, gesture, or image recognition are possible with TensorFlow applications. The cloud is impressively powerful but all-the-time connection requires power and connectivity that may not be available. Edge computing handles discrete tasks such as determining if someone said "yes" and responds accordingly. The audio analysis is done on the MicroMod combination rather than on the web. This dramatically reduces costs and complexity while limiting potential data privacy leaks.
