Cable Trackers
Identify a wire's path.
-
Product
Cable Tracing
Tone and Probe
-
The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation. It allows for pin point identification even in the most congested cable bundles. Our unit can be used with any tone generator.
-
Product
Wireless Functional Test Fixtures
-
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Product
Circuit Testing & Tracing
-
A versatile circuit tracer can do more than just help you locate the breaker that supplies a particular load. Breaker finders can also quickly identify and troubleshoot energized outlets. Circuit and wire tracing kits can trace energized or de-energized circuits without power interruption, locate individual wires in a bundle and find shorts and ground faults.
-
Product
Advanced Wire Tracers
-
Amprobe’s Advanced Wire Tracers provide accurate results in minutes with new features and technologies that simplify wire tracing and breaker identification, including two optimal frequencies for both energized and de-energized wire and breaker tracing in walls, ceilings, and floors.
-
Product
Cable Tracers
-
Shanghai Beha Electronics Co., Ltd.
*Trace wires or cables.*Continuity and polarity testing.*Digital Multimeter
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
Auto Circuit Tracer
7411
-
Peaceful Thriving Enterprise Co Ltd
Find short and open circuits quickly and easily in DC circuits from 6-42V. Designed to identify and trace wires or cables without damaging the insulation.
-
Product
Circuit Tracer Detector
7410
-
Peaceful Thriving Enterprise Co Ltd
Find short and open circuits fast and easily. It is designed to identify and trace wires or cables without damaging the insulation; you just simply attach the sender unit to the circuit and follow the wires by using the detector. There is a sender and a receiver included in the instrument.
-
Product
Tone Generator with Cable Tracer
1RA470
-
Cable tracer is designed to trace wires without damaging the instalations. It has wolume control to increase sensitivity. Power supply is standard 9V battery.
-
Product
Impact Tools
D914™ Series
-
The D914™ Series impact tools provide quality terminations on the first punch, helping to achieve the highest quality possible on network installations. They are the only impact tools that combine torque and impact in one tool. They also include a built-in hook and spudger into the handle. Use the hook to remove wires from any style block or to help trace wires. Use the spudger to remove the cross-connect module from the mounting bracket. Quick and easy blade replacement, and extra blade storage available in the handle.
-
Product
LAN/Ethernet/Telephone Cable Tracker & Tester
PHCT65
-
Trace Telephone Wire and LAN CableTrace Wires In Electrical SystemVerify LAN Cable ConditionContinuity TestDC Voltage ProbeBright White LED FlashlightSold as : Unit
-
Product
Net Toner and Probe Kit
1EA680
-
Cable tracer is designed to trace wires without damaging the instalations and much more.
-
Product
USB Cable
143556-02
-
USB Cable - The USB Cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use this cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
Product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks) to 4x50-Pin IDC, Male, 1m
40-971B-200-1m-FM
-
This female rear exit to male ribbon 1m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks.
-
Product
SMB Female to BNC Female Cable, 50 Ohm, 61 cm
763389-01
-
The SMB-BNC Coaxial Cable, sometimes referred to as SMB-100 or SMB-110, connects measurement and signal devices. NI offers this 50 Ω cable in different lengths and quantities.
-
Product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks) to Unterminated (Tinned Ends), 0.5m
40-972B-200-0.5m-FU
-
This female rear exit to unterminated 0.5m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to its mating connector by female screwlocks.
-
Product
10-meter (33 feet) Sensor Cable
E1739B
-
The E1739B 10-meter (33 feet) Sensor Cable is used to connect the E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.Other cable lengths available: E1739A 5-meter (16 feet), E1739C (49 feet) 15-meter and E1739D 25-meter (82 feet).
-
Product
3-Pin Power D-Type Cable, Male to Male, 2m
40-970-403-2m-MM
-
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly, Receiver, Mini Coax, 36", 9 SMB Plugs
540062010207
-
Cable Assembly, Receiver, Mini Coax, 36", 9 SMB Plugs
-
Product
Cable Assembly, Receiver, 36", Tripaddle, 96 Pin 2X InfiniBand SMB
540285010203
-
Cable Assembly, Receiver, 36", Tripaddle, 96 Pin 2X InfiniBand SMB.
-
Product
Cable Assembly, Receiver, 36", Micro Power and Micro Coax, 4 BNC Plugs and 4 SMB Plugs
540297010247
-
Cable Assembly, Receiver, 36", Micro Power and Micro Coax, 4 BNC Plugs and 4 SMB Plugs
-
Product
Cable Assembly, 104-Pin D-Type, Female to Unterminated, Tinned Ends, 2A, 1m
A104HFR-T-0A100
-
This 1m long female to untermiated 104-Pin D-type Cable Assembly is suited for direct connection to various products using the 104-Pin connector. It is constructed from high-flexibilty, high-specification fully screened cable and is unterminated with tinned ends.
-
Product
68-Pin SCSI Micro-D M to 2x34 2m
40-971-068-2m-MF
-
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 2x34-Pin Twisted Pair cable with PVC insulation, terminating with 2x34-Pin polarised IDC connectors. Strain relief is provided via a metal spring latch on the 68-Pin connector.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 0.5m, Exit Towards Pin 1
A050DF5-050DF5-0A050
-
The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
-
Product
Row Expansion Cables
Y1134A
-
Easily configure an expanded matrix using this expansion cable with the 34934C and 34934T terminal blocks
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Tinned Ends, 2m
A015DM5-T-0A200
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m
A050DF5-C-0A050
-
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 1m HV, Exit Away From Pin 1
A050DM4-T-HA100
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 1m HV, Exit Away From Pin 1
40-970-050-1m-MF-HV
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
