Broadcast Monitoring
-
Product
Torque Measuring and Monitoring System
WISER 4000
-
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
Product
CO2 And H2O Monitor
EGA30
-
A highly stable monitoring system that measures CO2 to 1ppm in a range of 0-2000ppm, and H20 to 1% relative humidity in a range of 0-100% relative humidity. The instrument is designed for long-term monitoring.
-
Product
Thermal Control and Monitoring
-
Harmonize and control your entire data center thermal management system to achieve up to 50% higher efficiency, improve protection and security and enhance staff productivity.
-
Product
Portable PD Monitoring
ASM-P
-
The ASM-P can be configured with up to 32 PD sensor channels. If excessive discharge is detected, the ASM-P raises an alarm that can be configured either locally or by email/SMS. This enables the long-term assessment of plant conditions to be carried out quickly and easily, from any remote computer.
-
Product
Clamp-On Ultrasonic Flow Monitor
KATflow 10
-
The KATflow 10 is a simple ultrasonic clamp-on flow monitor, which provides an extremely cost-effective alternative to in-line flowmeters on effluent, wastewater and sludge applications. The KATflow 10 is used to monitor the flow of liquids containing higher levels of solids or entrained gas bubbles for measurements where a general flow indication is sufficient. The instrument is extremely simple to install and commission and is ideal for applications which demand good repeatability and reliable results.
-
Product
Portable Dew Point Monitor
1500
-
The Model 1500 is a self contained system; not only is there no field assembly required, there’s no need to carry around a myriad of individual components such as control boxes, sensors, cables, pumps, and power cords. Simply attach the sample line, adjust the flow (with the integral flow meter) and turn on the power. Within minutes you’ll be collecting field dew point data with the same chilled mirror accuracy of a lab standard hygrometer. And with a nominal battery life of 12 hours, you will be able to collect for the entire shift or spot check your processes for several days.
-
Product
Micro Volume pH Monitor
UP-100
-
Redevelops HORIBA's founding pH measurement technology using new ultra-small capillary electrode. HORIBA's UP-100 affords ultra-low sample consumption of just 500 uL/measurement, enabling continuous pH monitoring for a variety of critical manufacturing processes that include Semiconductor (Cleaning, Etching and Plating); Chemical Manufacturing, Bio, Pharm, Food Processing, etc.Designed for 6 month continuous operation without operator intervention for minimizing downtime.
-
Product
Highly Sensitive Silica Monitor
SLIA-300
-
Highly sensitive silica monitor for ultrapure water management in semiconductor/FPD processes
-
Product
PXI Monitored Multiplexer, Quad 32-Channel, 1-Pole
40-619-204
-
The 40-619-204 is a high density PXI 2 A multiplexer module in quad 32-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
Vapor Concentration Monitor
IR-300 Series
-
Metal-Organic Chemical Vapor Deposition (MOCVD) is widely used in the manufacture of LEDs, optical devices and other components. Liquid and solid precursors are delivered to the reaction chamber by controlling the temperature, pressure and the carrier gas flow rate (bubbling method). Process results can be affected by changes especially in temperature and liquid level. The in-line IR-300 Series measures and reports the precursor concentration in real time.
-
Product
Critical Process ESD Monitor
Novx Series 7000
-
Simco-Ion's Novx Series 7000 Process Monitor is a multi-purpose microprocessor based instrument for monitoring critical electrostatic related parameters in work station and process environments. The six dedicated use channels provide the flexibility to customize the instrument for the monitoring capability and communication required at each location.
-
Product
Transmitter Monitors Carbon Monoxide
CO-R
-
The CO transmitter monitors carbon monoxide (CO) levels and is designed for the continuous monitoring of vehicle exhaust in non-hazardous areas. The CO uses a wide spectrum, long life electrochemical sensor to measure the amount of carbon monoxide in the environment. It is offered with an operating range of 0 to 125 ppm. Both the Room and Duct CO transmitters are offered in a standard NEMA 1 rated ABS Polycarbonate plastic enclosure. An optional NEMA 4X watertight and dust proof enclosure is only available with the CO room transmitter.
-
Product
Ultrafast Photodetector with Current Monitor, 1250 - 1650 nm, DC - 20 GHz, FC/PC
DXM20AF
-
The DXM20AF Ultrafast Detector is a DC - 20 GHz, fiber-coupled, InGaAs-based photodetector designed for applications in the 1250 nm - 1650 nm wavelength range. The core element of the detector is the fiber-coupled, hermetically sealed, microwave detector module. For convenience and simplicity of use, the module is mounted inside a rugged housing that includes a rechargeable battery, current monitor circuitry, and a digital display of the DC photocurrent.
-
Product
PM Mass Monitor
Model T640
-
Teledyne Advanced Pollution Instrumentation
The Model T640 PM Mass Monitor is the next breakthrough in ambient particulate monitors. The T640 delivers 1-min or better time resolution with exceptional sensitivity and precision. The instrument is very low maintenance and requires no sample media for minimal cost of operation.
-
Product
19" 1280 X 1024, VGA/DVI Interface, Ultra Slim Touch Open Frame Monitor
IDS-3119
-
19" 1280 x 1024 SXGA panel with LED backlight for 20% power saving and environmental protection. 0~ 45° C operating temperature support, 5-wires resistive touchscreen solution, Combo touch interface of RS-232 and USB.
-
Product
Aerosol Particle Monitor
AES-1000
-
The Kanomax Aerosol Particle Monitor features an easy-to-read display, can connect to a network via ethernet, and offers simplified monitoring of particulates at multiple locations.
-
Product
15" XGA Industrial Panel Mount Monitor
IDS-3215
-
15" XGA LCD panel with LED backlight for 20% power saving and environmental protection. -20° ~ +60° C wide range operating temperature, 5-wire resistive touchscreen solution or tempered smudge resistant protected glass.
-
Product
Real-Time Content Monitoring System
ORION
-
Interra Systems' ORION is a real-time content monitoring system that enables service providers to deliver error-free, superior quality video. ORION provides real-time monitoring of IP-based infrastructures that looks at all aspects of video streams such as QoS, QoE, closed captions, ad-insertion verification, reporting and troubleshooting. ORION performs critical monitoring functions on hundreds of services simultaneously from a single platform, providing an operator with a single point of visibility and access to important information such as, status, alerts, alarms, visible impairments, error reports, triggered captures and more. ORION effortlessly monitors streaming content scaling single to multiple monitoring units/ sites across different geographical locations.
-
Product
21.5" Full HD, 1920 X 1080, VGA/DVI/HDMI Interface, Panel Mount Monitor
IDS-3221W
-
21.5" Full HD 1920 x 1080 LCD panel with LED backlight for 20% power saving and environmental protection. 0 ~ 45° C range operating temperature, 5-wire resistive, Pcap touchscreen or 3mm tempered protected glass.
-
Product
Industrial Panel Mount Monitors, PCs, and HMIs
-
Explosion- Proof HMIs Corvalent Panel Mount all-in-one system HMIs are water, dust, and explosion-proof. Our Explosion-Proof Industrial HMIs are compliant with IP66, NEMA 4X, and C1D2 standards and are the best solution for environments prone to explosion. -Visio Z15R-XP Explosion-Proof -Visio Z19R-XP Explosion-Proof -Visio Z21.5R-XP Explosion-ProofAll-In-One Industrial HMI Displays Corvalent’s full line of Industrial HMIs is rated IP65 to IP69K, as well as ATEX Marine. These all-in-one HMI systems are available in a wide variety of display sizes, ranging from 7“ to 21.5“.Industrial Panel Monitors Corvalent’s Industrial Panel Monitors are built with the highest quality materials. They are rated ATEX Marine, as well as IP65 to IP69K. Industrial Panel Monitors are available in display sizes ranging from 7” to 21.5”.Industrial Panel PCs Corvalent’s Industrial Panel PCs are built with longevity in mind. They can withstand the stresses an industrial environment places on technology rated IP65 to IP69K and ATEX Marine. -Visio PPC-17RES -Visio PPC-19RES -Visio PPC-21RES -Visio PPC-24PCT
-
Product
Transportable Monitors
BM 25 & MX 40
-
Teledyne Gas & Flame Detection
The BM25 packs the benefits of a fixed system area monitor into a rugged, user-friendly and transportable instrument. It was designed to detect one to five gases for mobile or temporary work applications, team protection, area surveillance or places where fixed detection systems are not suitable.Powered by a NiMH battery pack, the BM 25 multi gas monitor offers up to 170 hours of continuous run time. Other standard features include STEL and TWA values, as well as a data logging capacity of more than four months. Multiple units can be grouped using optional alarm transfer kits. This protects larger areas by transferring alarms from one BM 25 to the next. An intrinsically safe trickle charger is also available for long-term area monitoring in classified zones.
-
Product
Monitoring & Control Systems
-
PBE's Vantage software is designed to allow users to monitor real time data from a site remotely and accurately. Vantage allows for tracking, telemetry monitoring, alerting, and reporting of data to users. It can be configured to accept telemetry from almost any device via custom developed drivers. Capable of importing CAD maps and image files the mapping software offers a 2D GUI with icons. Vantage also offers historical playback of the data reported to replay a set timeframe. Reports are customizable and exportable to multiple common formats.The user configuration manager allows for user defined roles to grant or restrict access to and from all modules and features of those modules. The Electronic Tag Board module offers a tagging system designed to track assets that are checked in or out, while the Asset Summary module provides a list of assets with user selected telemetry streams and configurable alerts. Vantage provides location tracking and tagging, telemetry monitoring, ventilation control and reporting off data to users.
-
Product
Low Concentration Type HF/HCl/NH3 Concentration Monitor
HF-960M
-
The HF-960M uses sensors that offer outstanding corrosion resistance for high-precision, high-speed measurement of low concentrations of hydrofluoric acid, hydrochloric acid and ammonia, and is thus perfect for single-bath and wafer cleaning. The HF-960M is also an environmentally-friendly product that uses lead-free solder for mounting chips on the PCB.
-
Product
Ultrafast Photodetector with Current Monitor, 700 - 870 nm, DC - 12 GHz, FC/PC
DXM12CF
-
The DXM12CF Ultrafast Detector is a DC - 12 GHz, fiber-coupled, GaAs-based photodetector designed for applications in the 700 nm - 870 nm wavelength range. The core element of the detector is the fiber-coupled, hermetically sealed, microwave detector module. For convenience and simplicity of use, the module is mounted inside a rugged housing that includes a rechargeable battery, current monitor circuitry, and a digital display of the DC photocurrent.
-
Product
Vibration Monitoring
-
From milling machines to pumps to wind turbines – wherever the condition of machines and systems needs to be monitored, Pepperl+Fuchs vibration monitoring products help prevent unplanned downtime and ensure personal and system protection.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Optical Performance Monitor
-
Optoplex Optical performance monitor (OPM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical performance monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controlling network elements so as to optimize operational performance. In particular, Optoplex Optical performance monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength and power. See the following schematic diagram for OPM working principle.
-
Product
21.5" Full HD Standalone HD Base-T Multi-Touch Industrial Monitor
SPC-821(M) V2
-
21.5" Full HD TFT LED LCD display16:9 widescreen with P-CAP multi-touch controlSupport HD Base-T long distance video streamingFront-facing LED indicators show operating statusSilicone-free enclosure with all-round IP65-rated protection
-
Product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
-
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
-
Product
Automated Monitoring of Airborne Molecular Contamination
AMC-Monitor T-1000
-
The all-in-one analyzer for FOUP, fab and clean-room environment AMC monitoring in the semiconductor industry. The AMC-Monitor is a modular and flexible platform for airborne molecular contaminations (AMC) monitoring in semiconductor applications such as: FOUP analysis with a focus on VOC and condensables incl. full integration with Pfeiffer Vacuum APA 302 pod analyzer. Clean-room monitoring in fabrication plants.
