Fault
-
Product
20Hz Injection Kit Monitoring System
-
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
-
Product
Automatic Oil Insulation Test Kit
-
The test kit is fully automatic and has the facility forAuto/Manual selections. The operator simply needs thesample in the test vessel & selects the required test. Testingcan be done as per many international ( IEC & Europeanstandards ) which are programmed into the instrumentmemory . Stand time, Stir times & Rate of rise of appliedvoltage can be selected in Custom Mode also , one setof such selected mode can also be stored in the memory. In addition to the above set can also perform withstand test(proof) tests. In this test the set allows the set voltage to pre-set value & hold for one minute to see if breakdown occurs. The backlit LCD is used for user friendly operationsduring the test process. It also display fault condition messages such as open ground and cover open . All the user selected programmes are chosen through(4x3) key pad.The test results can be printed along with with test type, date, time, breakdown test voltage, averages and deviations. Voltage value can be measured & printed with a resolution of 0.1kV. In reprint option it is possible to have number of printouts for the last test. For each test the readings are recorded and stored in memory.
-
Product
GPS/GNSS Antenna Signal Splitter 4-Way, TNC Female, IP67 Weatherproof, 1-2 GHz
GPS421
-
INSTOCK Wireless Components, Inc
GPS421 is a four way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked ports is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
-
Product
RAID Box
-
Protects critical data and ensures uptime without software. Built for 24/7 industrial reliability and fault tolerance.
-
Product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCIe-7256
-
ADLINK's PCIe-7256 features all Form C type relays, ideal for device connection with on/off control. With latching relays, the PCIe-7256 further provides operating power conservation, while the status of each latching relay output is indicated by onboard LED. When the relay is in SET, its corresponding LED lights. Latching relays also feature unchanged status even when the system powered off, making the PCIe-7256 suitable for critical applications requiring output status to be maintained even under fault conditions. All digital input channels are non-polar and optically isolated, and may be set for optional use of RC filter. The PCIe-7256 also features a change-of-state (COS) function generating interrupt when any digital input changes state.
-
Product
Thermocouple Simulator Module for SLSC
-
Bloomy’s 8-Channel Thermocouple Simulator Module provides eight channels of galvanically-isolated thermocouple simulation and simulates types E, J, K, M, N, and T thermocouples. High-precision digital-to-analog converters which are isolated from each other and from system power provide sub-microvolt resolution and accuracy. Built-in switching provides open-circuit faults as well as switching to system calibration resources.
-
Product
Optical Extended CAN Bus Jumper
EOFL-C
-
Optical Extended CAN Bus Jumper, using fault tolerant to optical conversion to extend the range, can extend up to 5 kilometers subsea.Qualified repeater housing protected on each side by highly reliable glass to metal sealed penetrators.
-
Product
Power Dividers & Splitters
-
Keysight dividers and splitters are used in a wide range of applications, such as: transmission line fault testing, power combining, source leveling, ratio measurements, power splitting, and critical signal processing applications that require minimal insertion loss and high port isolation.
-
Product
Portable OTDR Tester
CARY-OT4000
-
The CA OPTRONICS CARY-OT4000 series portable optical time domain reflectometry (OTDR) is the latest FTTx optical fiber cable-based test instrument. It has light weight, elegant appearance, small size, easiness of installation and maintenance, high-capacity built-in battery. It provides multiple built-in test wavelengths and optical testing functions like visual fault locator (VFL). As a new product specially designed for FFTx network testing, it provides site technicians with the highest performance and upgrade services.
-
Product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
-
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
DC Ground Fault Finder
FST-JD200
-
Foresight Electronics Co., Ltd.
FST-JD200 not only can provide a solution on accurately testing the faults of the indirect-grounding of the direct current system, non-metal grounding, loop grounding, simultaneous grounding of the anode and cathode, balanced grounding of the anode and cathode and multi-point grounding 1.
-
Product
GAOTek Handheld Gigabit Ethernet Tester
A0060001tek
-
GAOTek Handheld Gigabit Ethernet tester is designed for installation and maintenance of 10 M/100 M/1000 M Ethernet networks. It combines the functions of network testing, data packet capture, traffic generation, cable testing and BER testing into one unit. It also integrates full RFC-2544 and Y.1564 tests. Featuring an ergonomic design and 5.0 inch LCD color touch screen, this Ethernet tester helps the front-line field workers to analyze the network quality and locate faults rapidly. Test results can be shown graphically and numerically.
-
Product
Fault Locator
BIDOYNG
-
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
Product
Hardened Media Converter, 1000Mbps, Multimode 850nm, SC
EKI-2741SXI
-
Provides 1 x 1000 Mbps Ethernet port with RJ45 connectorProvides 1 x 1000 Mbps fiber port with SC or SFP (mini-GBIC) type connector for 1000Base-SX/LX deviceProvides DIP switch for full/half duplex settingSupports MDI/MDI-X auto crossoverSupports Auto-NegotiationSupports redundant 12 ~ 48 VDC power inputProvides flexible mounting: DIN-rail and Wall mountProvides Link Fault Pass-through (LFP)Jumbo Frame: 9K bytes
-
Product
4 Station Endurance Test Setup for Thermostat of Iron
-
SCR ELEKTRONIKS have developed 4 STATIONS ENDURANCE TEST SETUP FOR THERMOSTAT OF IRONwhich is used for carrying out endurance test for thermostat of iron for the required amount of time It is very useful and handy in line testing on Mass production line as well as type Testing. It consists of Voltmeter, Wattmeter, Programmable Logic Controller( PLC ). The equipment continuously monitors faults like Contact weld and Contact Open. The other important feature is we can operate the panel in Auto Mode or Manual mode. User friendly operations make the equipment to be handled easier for any operator. This manual contains information about operating instructions and maintenance of the equipment.
-
Product
Photovoltaic System Bypass Diode Tester
FT4310
-
Hioki is pleased to announce the launch of the Bypass Diode Tester FT4310 for Photovoltaic Systems. The FT4310, which is designed to test bypass diodes in strings of crystalline photovoltaic cells, can be used to detect open and short-circuit faults in bypass diodes by string either in daylight or at night. The instrument is the first portable device capable of detecting bypass diode open faults in operating panels (without requiring the panels to be shielded from sunlight).
-
Product
Vector Network Analyzer
ZNLE
-
The renowned high-quality design, innovative user interface and compact size of the R&S®ZNLE make it ideal for basic VNA applications. The time domain analysis option (R&S®ZNL-K2) and distance-to-fault measurements option (R&S®ZNL-K3) enhance the R&S®ZNLE with essential features for general purpose testing.
-
Product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
-
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Optical Time Domain Reflectometer
OTDR II
-
The OTDR II (Optical Time Domain Reflectometer) excels in fault finding on fibre cabling with industry-leading specifications and performance levels on both single-mode and multimode fibre networks. Not only does OTDR II deliver accurate test data and pass/fail results, it also offers automated fault-finding capabilities that help to minimise network downtime.
-
-
Product
PCI-6516, 32-Channel, ±30 V, Source Outputs, Bank-Isolated Digital I/O Device
779082-01
-
The PCI-6516 is an industrial digital output interface, with one bank of channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6516 module is an industrial digital I/O interface, with all channels on an isolated bank. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6516 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
Network Cable Testers
-
Companies expect their Ethernet twisted pair cabling to work flawlessly, but corners cut during design, installation and testing result in network downtime which translates to wasted resources and lost revenue. This can be avoided by cable installers that can install copper cabling systems and locate faults quickly.
-
Product
Mini PoE+ Media Converter, 1000Mbps, SFP (Also Known As MiniMc 857-11911TG)
IMC-390-SFP
-
Supports IEEE802.3at PoE+ (25.5W) and IEEE802.3af PoE (15.4W) standardsServes as a power sourcing equipment (PSE) deviceSupports jumbo frame functionality (up to 10240 bytes)Supports multiple mounting options (desktop, DIN rail or wall-mount)Features in configurable PoE reset on fiber LOSSupports Link Fault Pass Through (LFPT)
-
Product
PXI/PXIe Fault Insertion Switch, 64-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-112
-
The 40-190C-112 (PXI) and 42-190C-112 (PXIe) are fault insertion switches with 64 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Multiple Gas Transformer DGA
MULTITRANS
-
The MULTITRANS is an 8-gas on-line transformer DGA monitoring unit designed to monitor a bank of three single-phase transformers in close proximity. Based on the same core technology as the highly successful TRANSFIX the MULTITRANS measures all significant fault gases (in ppm) as outlined by international standards as well as moisture in oil (%RH & ppm).
-
Product
Pentype Visual Fault Locator
RA3105
-
Radiasun International Group Ltd.
The RA3105 Pentype VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes: Finding the breakpoint, poor connections, bending or cracking in fiber optic cables. Finding the faults of OTDR dead zone End-to-end visual fiber identification.
-
Product
Isolation Power Panels for Healthcare Facilities
-
Standards such as NFPA 99 and CSA Z32 require isolated power systems in all areas deemed “wet procedure locations” in healthcare facilities. Isolated power systems offer an invaluable advantage - early detection of ground faults allows for critical systems to remain online in a single fault condition.Bender isolated power panels provide isolated power to electrical systems in operating rooms and other critical care areas. Utilizing the latest in technology, Bender equipment ensures that electrical ground faults are detected and located fast and automatically, in compliance with the latest standards and code requirements.
-
Product
PXI-6511, 64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated PXI Digital I/O Module
778967-01
-
64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6511 is an industrial digital input interface, with eight banks of isolated channels. If a computer or application fault occurs, the PXI‑6511 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Desktop/Wallmount Chassis
IPC-7130L
-
Desktop/Wallmount Chassis for ATX/MicroATX Motherboard with Dual Hot-Swap 3.5" Drive Bays. Shockproof drive bays - One 5.25", one internal 3.5", and two hot-swap 3.5" trays for IPC-7130 / two 3.5" HDD device trays for IPC-7130L. Lockable front door prevents unauthorized access, LED indicators for system fault detection.
-
Product
Vacuum and Fuel Pump Tester
DVG1
-
Suitable for testing and fault finding the following in petrol engines including: Spark misfires; poor engine compression; weak/rich mixture; ignition over advanced/retarded; inlet manifold and carburettor air leaks; incorrect valve timing; poor fuel economy; balancing carburettors; turbo boost gauge; fuel pump testingDisplay packed.
