J1
-
product
VME J1 10 Slot with ADC Connectors
101VMEJ110-0590
VME J1 backplane 10 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
Airborne Receiver
MS 2015
Receiver shall receive the telemetry signal transmitted by the airborne TGS unit. This unit is a single conversion super heterodyne FM receiver operating at 1486.5MHz. This unit has four connectors. They are RF input connector (J1), Power connector (J2), Signal connector (J3) for AGC signal and a Video output connector (J4). This unit operates at 28V DC and consumes a typical power of 5.6 watts.
-
product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
VME J1 18 Slot with ADC Connectors
101VMEJ118-0590
VME J1 backplane 18 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 7 Slot with ADC Connectors
101VMEJ107-0590
VME J1 backplane 7 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME Type 32 with 6U, 5 slot Backplane
32V05MMX36N3V10
VME Type 32 with 6U, 5 slot Backplane J1, J2.
-
product
VME Test Extender 9U/220mm J1/J2/J0
111EXT9122-0120
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Single Rear Slot Universal ISA plug-in PCMCIA Adapter
J105
* High reliability 68 pin PCMCIA compliant,* static protected, connectors with card eject buttons are used.* Standard Types I, II and III cards,* 5V cards supported.* Operating temperature range: 0-50 C* ISA board dimensions: 150 x 100 x 24mm Host Computer:* Any true compatible Pentium PC or higher with ISA Bus.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Simulators (Gen II)
J1939
The Au SAE J1939 simulators (Gen II, includes V1.00A releases and V2.00A releases) can generate SAE J1939 signal for up to three controller applications (CA): Engine, ABS and Transmission. Au J1939 simulators are designed so easy to use, even product line operator and sales personal can use them without Controller Area Network training. Au J1939 simulator can run all by itself and doesn''t require complicate software settings or user''s knowledge and experience on Controller Area Network. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
product
Cable Assembly, Receiver, 36", Micro Power to 41-Pin FML Power Connector, for VTI EX1200-2001 Switch Module
540249010247
CBA, RCV, MicroPWR to 41-Pin J1 PWR Conn f/VTI EX1200-2001 Switch Module.
-
product
Mini Logger
J1939
The DAWN J1939 Mini Logger™ is a compact logger that acquires CAN bus data from heavy-duty trucks, buses, and off-road vehicles. It fits directly on the J1939 connector. The J1939 Mini Logger is part of the Mini Logger family of compact, low-cost, data loggers that acquire a variety of data from trucks and cars.
