-
product
CTEL 6U 5 slot with ATX, P1P2P4s, P3P5l, RoHS
104CTEL605-4146R
CompactPCI CTEL 6U 5 slot with system slot left, H110 bus, ATX connector, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
-
product
PMC to PCI Adapters
The PMC to PCI, PMC to CPCI and PMC to PC/104+ adapters enable the use of the PMC650 or PMC850 bus analyzers in PCI, CompactPCI and PC/104+ systems. The PMC analyzer plugs onto the adapter and then the mated adapter and analyzer plug into a PCI, CompactPCI or PC/104+ system. These passive adapters route the bus signals from the analyzer to the bus with minimal trace length and impedance matching. The adapters provide the full 64 bit interconnect between the analyzer and the bus.
-
product
Industry Pack Carriers and Digital I/O
CPCI-IPC
The CPCI-IPC module provides a 3U high performance flexible I/O scheme, that supports industry standard Industry Packs™. For application requiring low cost, high density I/O or unique combinations, the CPCI-IPC is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via the CompactPCI bus. A very low cost, non-intelligent version is also available, CPCI-SIP.
-
product
Electronical Load Board 3U CompactPCI (conduction cooled)
046-712
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
- ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch- 24-port fully managed Gigabit Ethernet switch- Pre-installed ADLINK PacketManager accelerates packet processing- Layer 2/3 switching with advanced support for VLANs, QoS and IPv6- Two 10 Gigabit Ethernet SFP+ uplink ports- Supports IPMI based on PICMG 2.9 (System Management Specification)
-
product
16 Bit PXI I/O Board With 32 Or 64 Analog Outputs
CP266
The CP266 is a single-width, 6U, CompactPCI module with 32 or 64, 16-bit analog output channels. These independent analog channels provide ±10 V full-scale outputs. The channel update rate is 2ms, and each output is accurate to ±1mV. The power-up state of the analog outputs can be set to independent user-defined values. Paired output signals are provided to eliminate ground offset effects. The analog outputs are available at a single 68-pin SCSI II shielded connector (32-channel option) or a pair of 68-pin SCSI II shielded connectors (64-channel option).
-
product
64-CH Isolated Digital I/O Modules
cPCI-7432/7433/7434
- Two external interrupt sources for cPCI-7432/7432RP/7433- 3U Eurocard form factor, CompactPCI compliant (PICMG 2.0 R2.1)- 32-CH isolated digital inputs & 32-CH isolated digital outputs for cPCI-7432- 64-CH isolated digital inputs for cPCI-7433- 64-CH isolated digital outputs for cPCI-7434/7434P- 5000 VRMS isolation voltage
-
product
CompactPCI Backplanes
The CompactPCI standard was created to address a large range of applications, including aerospace and defense as well as communications and industrial. The standard supports both 3U and 6U cards and allows for both convection (air) and conduction cooling. Since its release in 1995, it has also been extended multiple times.
-
product
CompactPCI 6U 64 bit ATX 5 slot, P1s no P2-5, RoHS
102CPCI605-41XXR
CompactPCI 6U 5 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
product
3U CompactPCI Quad-Core Intel Atom® Processor X Series Blade
cPCI-3640 Series
- Low power quad-core Intel Atom® x6413E Processor (formerly Elkhart Lake)- Up to 32GB DDR4-2400-3200MT/s ECC soldered memory- Optional onboard SSD support- Flexibility in IO selection- Extended temperature -40 to 85 degree C supported
-
product
Windows Driver & SDK for ADLINK USB DAQ Series Data Acquisition Modules
UD-DASK
ADLINK DASK drivers are the device drivers for custom data acquisition applications for Windows. The DASK driver libraries provide API sets for ADLINK PCI ExpressR, PCI, CompactPCI, PXI and USB data acquisition cards, to access full hardware functionalities, such as buffered/double-buffered data acquisition, pattern generation, digital input/output and etc. For novice users, the built-in CodeCreator utility helps you create your first program in just a few minutes.
-
product
3U CompactPCI-Serial CPU Boards
Advantech’s 3U CompactPCI-Serial board offers latest Intel Xeon®/Core™/Atom based processor blades.
-
product
CTEL 6U 6 slot with ATX, P1P2P4s, P3P5l, RoHS
104CTEL606-4146R
CompactPCI CTEL 6U 6 slot with system slot left, H110 bus, ATX connector, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
-
product
GPIB Controller Card
GPIB-cPCI-XL
The GPIB-cPCI-XL is a GPIB controller card for PXI and CompactPCI computers.
-
product
6U CompactPCI 9th/8th Gen Intel® Core™ I3/i5/i7 Processor Blade
cPCI-6640 Series
The ADLINK cPCI-6640 is a 6U CompactPCI® processor blade featuring an 8th/9th Gen Intel® Core™ (formerly Coffee Lake-H) with Mobile Intel® CM246 Chipset. Dual SO-DIMM slots provide up to 64GB of DDR4-2666 dual-channel memory (2x 32GB modules). ECC memory is also available when paired with a supporting CPU.
-
product
Electronical Load Board 6U CompactPCI (air cooled)
056-169
The 6U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
product
9U Blade Server for 12 Blades with Dual Fabric Switch Slots
cPCIS-3300BLS
- PICMG® 2.16 Packet Switching Backplane architecture- Dual PICMG® 2.16 fabric slots for high availability- 21 slots, including 12 node slots, two fabric slots, three redundant 6U CompactPCI® power modules and one CMM slot- Hot swappable 800 W + 400 W redundant CompactPCI® power supply with universal AC input
-
product
8-Slot 32-bit 6U CompactPCI Backplane
cBP-6108F
- PICMG:2.0 R3.0, 2.1 R2.0, 2.5 R1.0, 2.9 R1.0Note- Dimension:202.5 x 262.05 (mm, WxH, vertical insertion view)- Segment:One- cPCI Bus:32-bit/33MHz- System Slot:Right-hand side; System Slot Rear I/O:P3, P4 and P5 rear I/O with AB-type shroud
-
product
3U CompactPCI 9th Gen Intel® Xeon®/Core™ i7 Processor Blade
cPCI-3520 Series
The cPCI-3520 Series is a 3U CompactPCI blade available in single-slot (4HP), dual-slot (8HP) or triple-slot (12HP) width form factors with various daughter boards to provide a broad range of I/O requirements. Faceplate I/O in the single-slot (4HP) version includes 1x DVI-I, 2x GbE and 1x USB 3.0 port (these I/O are common to all versions). Faceplate I/O in the dual-slot (8HP) version includes additional 2x USB 2.0, 1x COM, 1x KB/MS and Line-in/Line-out on the cPCI-3520D or additional 2x DisplayPorts, 1x COM in RJ-45 connector, 1x KB/MS and 1x additional USB 2.0 port on the cPCI-3520G. Two more dual-slot options are the cPCI-3520L with additional 2x GbE, 1x COM and 2x USB and the cPCI-3520M with one 100-pin high density connector supporting additional 2x DVI-D, 2x USB 2.0, 2x COM, 2x KB/MS and Line-in/Line-out ports.
-
product
4, 8, 16 And 32 Channels ARINC429 Test & Simulation Module CompactPCI-Express/PXI-Express (3U)
ACE429-3U-x
4, 8, 16 and 32 channels ARINC429 Test & Simulation module for CompactPCI-Express/PXI-Express (3U).
-
product
CompactPCI PICMG 2.16 Backplanes
Comtel Electronics offers a large variety of CompactPCI 2.16 Backplanes, 8 – 14 slots 64 bit 33Mhz,Fully compliancy with PICMG 2.0 Rev 3.0 Specs & 2.16 Spec. Hot Swap compliant per PICMG 2.1 R2.0 Spec.
-
product
Board Drivers
9450-DRV
IOWorks board drivers are Abaco Systems' IOWorks data acquisition and control (DAQC) software driver. It is a hardware and operating system-independent driver designed to support the widest variety of I/O in the industry. The driver operates with many operating systems such as Windows NT/Windows 2000, QNX, VxWorks, and Linux, and delivers high performance and flexibility across multiple platforms such as CompactPCI, VME and PCI.
-
product
9U cPCI Chassis
DP-cPCI-8001
DP-cPCI-8001 is a compact high performance, high reliability 9U cPCI chassis.The DP-cPCI-8001 provides the right platform options to meet system integration needs. The chassis complies with the features defined by the CompactPCI specifications. Ruggedness, modular construction, integrated cooling and EMI-EMC protection are available. The DP-cPCI-8001is available with 4 -14 cPCI slot backplane and various power supply configurations.
-
product
cPCI Serial Power Supplies
CompactPCI Serial (PICMG CPCI.S-0) has added a number of features and benefits while maintaining backward compatibility to create a foundational spec for serial-based CompactPCI technologies. This includes an updated power supply specification. CompactPCI Serial requires only one +12 V power supply with a maximum power of 79.8 W per 3U module and 171 W per 6U module as well as a 5V stand-by voltage.
-
product
3U CPCI To PCI 4 Slot Adapter
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
product
6U CompactPCI Rear Transition Module with PCIe x16 and PCIe x4
cPCI-R6600 Series
6U CompactPCI rear transition module with PCIe x16 and PCIe x4
-
product
6U Compact PCI Single Board
CP62005
LinkedHope Intelligent Technologies Co.,Ltd.
CP62005 is a 6U CompactPCI® single board with high-performance, low power consumption and high reliability. It is ideal for ruggedized systems requiring high-bandwidth processing, or for information processing and embedded computing.CP62005 supports 4th generation Intel® Core™ i7 or i5 Haswell processors, up to 16GB onboard DDR3L memory. It also offers 16GB onboard SLC SSD for operating system and drivers. The onboard design of memory and SSD can enhance the anti-shock and vibration performance.CP62005 integrates Intel® HD Graphics 4600 controller, which supports a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA… CRT max resolution is up to 2048x1536. With HDMI/DP/eDP it can be up to 4K. It also supports three independent displays.
-
product
9-Slot 3U PXI Express Chassis with AC - Up to 8GB/s, All Hybrid
PXES-2590
The ADLINK PXES-2590 is a 9-slot PXI Express chassis equipped with advanced features and functions. Compliant with PXI Express and cPCI Express specifications, the PXES-2590 offers one system slot, one system timing slot, and seven hybrid peripheral slots for versatile test and measurement applications requiring enhanced bandwidth. The hybrid-slot design accepts installation of CompactPCI, PXI, CompactPCI Express, and PXI Express modules into any peripheral slots in PXES-2590, maximizing flexibility. The PXES-2590 is built on a four-link PXI express chassis with 8 GB/s system bandwidth, and 2 GB/s slot bandwidth for all peripheral slots.
-
product
14-Slot 32-Bit 6U CompactPCI H.110 Bus Backplane
cBP-6014R
- PICMG 2.0 CompactPCI Specification R3.0 Compliant- PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant- PICMG 2.5 H.110 Computer Telephony Specification R1.0 Compliant- PICMG 2.7 Dual system Bus specificationR1.0 compliant- One system slot with 13 expansion slots, system on the middle slot of the backplane
