Sensor Amplifiers
-
Product
Distribution Amplifiers
-
Distribute time code, radio frequency and other electronic impulses. Click a model below to learn more.
-
Product
Amplifier Modules
RF Amplifiers
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project.
-
Product
Isolation Amplifiers
-
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Product
Limiting Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's limiting amplifiers use FET device with good consistency and distributed traveling wave amplifying circuit to design. Good amplitude and phase consistency characteristics can be achieved in a wide input dynamic range. It's the key component of the electronic system. Keylink's limiting amplifiers can be categorized as follows.
-
Product
Variable Gain Amplifier
VGA
-
RF Lambda’s variable gain amplifiers (VGA) are standard amplifiers which include a gain control pin to allow the customer to tune the gain for various applications without sacrificing performance and eliminating the need to use a separate amplifier and attenuator. Hermetically Sealed options are available upon request.
-
Product
High-Voltage Amplifier
ZET 420
-
The high-voltage signal amplifier for emission of acoustic signals through capacitive emitters: sonic detectors (without integrated amplifiers), piezoelectric emitters, and transducers.
-
-
Product
Temperature Sensor
96000
-
The 96000 Temperature Sensor is a low-cost device that provides a simple, effective way to prevent damage and downtime caused by overheating of equipment. In monitoring equipment temperature, the sensor detects a potentially damaging or hazardous condition and alerts personnel to take corrective action. Application areas include bearings, gear boxes and motors.
-
Product
Infrasound Sensors
MB3a
-
The MB3a is an infrasound sensor developed by the CEA, following the MB2000 and MB2005 series, which allows the recording of very-low-frequency acoustic signals over a broad frequency band, with an excellent resolution and a large dynamic range.
-
Product
RF Bidirectional Amplifiers
-
Miniature, high-efficiency and linear bidirectional amplifier modules (transmit and receive). 1.0 to 2.5 GHz, automatic or manual T/R switching, high-efficiency or high-linearity models. Custom designs available through RF PA design services.
-
Product
Operational Amplifiers
-
Operational amplifiers from ams are ideally suited to audio applications. These CMOS devices are available as single, quad or differential amps. They feature good common-mode rejection, have low input bias currents, good gain bandwidth, low total harmonic distortion and an excellent rail-to-rail output-drive capability of 200mA peak.
-
Product
Web Sensor
T3511P
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
-
Product
10 MHz to 50/53 GHz USB Wide Dynamic Range Peak and Average Power Sensor
U2065XA
Power Sensor
The Keysight U2065XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz USB peak and average power sensor.
-
-
Product
Sensor
Hyperion Phycocyanin
-
Valeport’s Hyperion Phycocyanin Fluorometer sensor delivers high-performance measurements of Fluorescein, in a compact & robust package ideal as a standalone sensor, for ROV and AUV integration or used as part of a multi-sensor array and data logger.
-
Product
Sensor Technology
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT is the only manufacturer to utilize all 5 types of online partial discharge sensor technology. Using multiple sensing methods ensures that PD activity is always discovered, located, and characterized. PMDT's handheld PDetector and PDStar units have more capability than the high-end diagnostic equipment of the past. The small handheld, battery powered unit can completely perform the test and analysis without the need of a PC. PDetector, PDStar, and PDiagnostic instruments feature high-resolution phase-resolved analysis of PD signals (PRPD and PRPS) in real time, so you get your test results instantly!
-
Product
Flow Sensors
-
Accuracy±0.75% of full scale Measuring pipe size range DN 15 to DN 600(0.5 to 24 inch) Measuring flow rate range 0.15 to 8 M/s(0.5 to 26 Ft/s) Field-rangable supply voltage from DC 5 to 24 VS Field-rangable operting temperature from -20 to 90°C(-4 to 194°F) Protection class NEMA4(IP65) or NEMA6,6P(IP68) CE EMC certification
-
Product
Stud Sensors
-
Stud Sensors such as the MSV100 and MSV350D comprise a category of their own. Each uses electromagnetic induction to sense the presence of (and thereby locate) a stud, pipe, batten, current-carrying wire or other metallic object behind a wall or above a ceiling. The two instruments differ in their choice of the display technology (LED or LCD) used to pinpoint position.
-
Product
Sensors
NanoFocus Probe
-
Scan of 3D topography of high accurate featuresVery high point densitySuitable to perform non-contact roughness measurementsHigh flexibility using a range of different front lenses
-
-
Product
Voltage And Current Amplifier
KINGSINE KA30 / KA60
-
KINGSINE Electric Automation Co., Ltd.
KINGSINE's KA30 / KA60 voltage and current amplifier is high accuracy, high power, Panel-mounted type real time simulation power amplifier with four-phase voltage and three-phase current.
-
Product
CATV Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of single-ended and differential 75 Ω broadband amplifiers service head-end, HFC infrastructure Nodes, system and line-extender amplifies, EQAM and CPE applications. MACOM’s industry leading GaAs amplifiers are offered in a range of small, plastic leaded and leadless packages operating off standard voltage rails 5,8 & 12V. Covering reverse path, 5 – 300MHz, and forward path, 45 – 1800MHz, our amplifiers offer flat gain response, low distortion and high linearity.
-
Product
Amplifiers & Buffers
-
Renesas amplifiers are among the industry's highest-performance, highest-value amplifier ICs on the market. Our broad operational amplifier (op amp) portfolio provides for a wide range of next-gen precision instrumentation, medical, communication and industrial process control applications where innovation, reliability and dependability is central to the analog designs.
-
-
Product
Sensors
-
Diversified Technical Systems, Inc.
DTS offers a full line of high performance data acquisition systems, sensors, accessories and software to meet a wide range of critical test requirements. Let the DTS team of experienced engineers and test professionals help you find the right instrumentation for your application.
-
Product
Portable Power Amplifier
PAC60Cip
-
PAC60Cip is the portable conventional linear power amplifier model with six channels of current output. It is with 6*30A/210VA output, and this current amplifier is similar to PAC60Ci but it has lower output power and less weight.
-
Product
Load Cell Amplifiers
-
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
-
Product
Analytical Sensors
-
Conductivity sensors are pre-destined for use in the food industry. They detect the conductivity and concentration of different media and can differentiate between e.g. cleaning agents, rinsing water, and the food product. This means that it is not only possible to constantly track the product but also to reduce the waste of product and rinsing water – all possible without making adjustments to the sensor.
