Mains
chief conduit of electricity, gas or water distribution.
-
Product
Voltage Tester Pen
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
A non-contact voltage tester is the safest way to make sure the power is off without touching any wires. Before you open an electrical box, you should: - cut off power to the outlet at the main electrical panel - confirm you turned off the right circuit This is where the non-contact voltage tester comes in handy.
-
Product
PANTESTER Multi Cable Tester
PK-7890/7890PL
-
PANTESTER is an advanced multifunction pin-by-pin cable tester to verify cable integrity of Datacom. Telecom and Coaxial cables and displays the test results on the main unit.
-
Product
Circuit Breaker Analyzers & Timers
-
CAT circuit breaker analyzers and timers are advanced standalone or a PC controlled instruments for circuit breaker maintenance. Typical application areas of CAT instruments are medium and high voltage substations at electric power generation, transmission, and factories of switchgear. Also, industrial environments and electric power distribution are suitable application areas for these circuit breaker testing instruments.DV Power CAT circuit breaker testing instruments are portable and lightweight. They are designed for performing mechanical operations intended for circuit breakers testing according to standards IEC 62271-100 and IEEE C37.09.These instruments measure:the timing of main contacts, pre-insertion resistor contacts, auxiliary contacts operations,coil currents,motion parameters,voltage recording,main circuit resistance,arcing contacts wipe,and any relevant analog signal.Motion transducer channels provide measuring a displacement of the circuit breaker moving parts, contact wipe, over-travel, rebound, damping time, and average velocity. Even more, CAT circuit breaker analyzer optionally has a built-in micro-ohmmeter. Hence, it provides the main circuit resistance measurement and dynamic resistance measurement. Dynamic resistance measurement is an effective method for arcing contacts condition assessment.
-
Product
PC/104 OneBank Board
EMC2-ZU3EG
-
Sundance Multiprocessor Technology Ltd.
The EMC²-ZU3EG is a PCIe/104 OneBank™ SBC with a Xilinx Zynq SoC and a VITA57.1 FMC™ LPC I/O board. The main processing power of the EMC²-ZU3EG is a Dual Core ARM9 and combined with traditional FPGA fabrics/gates + High-Speed I/O interfaces, like USB2.0, HDMI, 1Gb Ethernet and SATA and provide an total solution for any Embedded Application.
-
Product
Beam Directional Power Supply Mains 60 To 180 kV
SiteX D1802
-
Our SITEX and SITEXS are capable of the direct and accurate measurement of high voltage. This essential information enables the control system to guarantee the stability and reproducibility of the radiological parameters based on true high voltage, ensuring extremely precise measurements-based utilization.
-
Product
Data Collection Systems
-
Data collection is an increasingly important part of manufacturing, and one of the main drivers in the movement toward electronic measuring tools with output. At the top of the Starrett line, DataSure Wireless Data Collection is a state-of-the-art system for real-time collection and recording of measurement data. transmission. From measurement to input, it reduces steps, saves time and can totally eliminate error in the data collection process. Starrett also offers several newer technology products for wire-based data collection; SmartCable for single tools and the 4-Port Gage Multiplexer.
-
Product
Self Testing Clamps with Visual Indicaiton
Bond-Rite REMOTE EP
-
The advent of the Bond-Rite REMOTE has allowed the further development of a mains Externally Powered (EP) version. This is ideal for applications where the clamp will be attached to plant / containers for prolonged periods of time, or where a monitoring system without interlocks is required (eg. for use during manual product transfer).
-
Product
PXI 8x4 Power Matrix, 2 Pole
40-550-002
Matrix Switch Module
Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current. These modules are fitted with electro-mechanical power relays, gold-flash over silver alloy. A spare relay is built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
Product
Standard Digital Multimeter - Auto Ranging
MM39
-
The MM39 is an auto-ranging multimeter with a large rotary switch for easy selection of the required test, even when wearing gloves. There are two test buttons, one to lock the range and the other to hold the results which are displayed on a 3½ digit LCD screen.
The main test functions are AC voltage and DC voltage and current and resistance. The MM39 measures both AC and DC voltage between 0.1mV to 600V and AC and DC current between 10mA to 10A. There is a diode test and an audible continuity test which sounds at less than 25Ω.
-
Product
MIL-STD-1553 Modules
-
> MIL-STD-1553B is the military specification defining a digital time division command/response multiplexed databus. The 1553 databus is a dual-redundant, bi-directional, Manchester II encoded databus with a high bit error reliability. All bus communications are controlled and initiated by a main bus controller. Remote terminal devices attached to the bus respond to controller commands. MIL-STD-1553B defines specifications for terminal device operation and coupling, word structure and format, messaging protocol and electrical characteristics.
-
Product
Detector, Metal, Power, Stud
72-6792
-
*Electronically locates hidden cables gas and water pipes*Traces hidden ceiling joists and wall studs*Senses presence of mains power withut touching live wires*Locates breaks in circuits and cables*Identifies faulty plugs switches and sockets*Incorporates audio signal and indicator light
-
Product
Optical Protection System ( Single Fiber Two-Way )
OPS-1000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OPS-1000 Optics Protection System product series, mainly applies to optical communication field of single fiber two-way for main, light path switching equipment. It makes up from light path switching unit, optical power monitoring unit and network management terminal. In optical communication networks, OPS-1000 real-time monitor the optical power of operating fibers and spare fibers, when monitor the optical light path’s optical power is lower than setting switching threshold, it will alarming prompt and switch to the spare fiber to realize the line protection of optical transmission system.
-
Product
LCR-Reader-MPA: Ultimate All-in-One Digital Multimeter
-
LCR-Reader-MPA combines tweezer probes with a powerful LCR/ESR-meter that is able to determine the type of component and best test parameters before measuring with a 0.1% basic accuracy. The device will display the main impedance value, any secondary values such as ESR, Q or D, component type and test parameters used instantly on a bright backlit LCD display. The 1 oz. device is very portable and ideal for fieldwork.
-
Product
Analyzers and Timers
CAT Advanced Series
-
Description The Advanced CAT Series Analyzers and Timers are stand-alone or PC-controlled digital instruments for circuit breaker status evaluation. Timing channels record arc closing and opening, resistance and auxiliary contacts. The main contact channels can also measure the resistance value of pre-insertion resistors (if present in the breaker). The advanced CAT series records graphs of the opening and closing coil currents and the movements of the moving parts of the high and medium voltage circuit breaker. Test results are printed on the 112 mm (4.4 inch) thermal printer (optional accessory) in tabular and graphical form. The advanced CAT series provides easy selection of different operating modes:
-
Product
Data Logger & Monitor
DLM-09
-
The Data Logger/Monitor has been designed to operate on 12V, 24V, 48V and 110V battery systems, with optional inputs for higher input Voltages, up to 550V. The Data Logger/Monitor is completely powered from the Batteries, and therefore a mains supply is not required. Therefore tests are not terminated part way through by a temporary mains power outage. The unit is lightweight and is completely portable. The Data Logger/Monitor may be left on site, unattended, for extended periods of time for data collection. Or used permanently as a Monitor / Alarm system.
-
Product
Single channel Motor Insulation Monitor
-
The SURETECH Motor Insulation Monitor measures insulation resistance to earth of electric motors when themotor stops. Motors running from mains (380 / 220V) and higher voltages up to 6.6kV can have their insulationcontinuously monitored.
-
Product
Inspection System
X-eye 7000B
-
Appropriate for the inspection of medium•large size components and detection of surface structure and defects (inside voids and cracks etc).Due to high-energy, high-power Micro-focus X-ray Open Tube, maintenance cost's significantly reduced and long-term use possible with only replacing consumables.Customization is available with selecting main parts by customers depends on their needs for size and material.
-
Product
ESD Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
Product
General Purpose Lab Oven
REXMED ROV-150
-
MOD. ROV-150, AC 110/230V, Plug type: , General purpose lab oven, dry air / hot air sterilizer, HS CODE: 841780, UNCCS CODE: 447483, UMDNS CODE: 14410, Main construction: powder coated steel and SS304, Controller: Microprocessor based PID controller, water proof keypad with timer, ˚C/PV and ˚C/SV display and setting, Timer: 9999/min, 9999/hr, Timer has DELAY_ON and DELAY_OFF function and at the end of operation audio and visual warning, Working range: Ambient +5˚C~250˚C, Stability at 37˚C: ±0.2˚C, Uniformity at 150˚C: ±1.5˚C, Sensor: PT 100Ω, Temperature audio and visual warning for AL-H and AL-L and OFS correction setting, Heater: 700W X 2pcs, Chamber: L50 X W50 X H60cm, Capacity: 150L, chamber with key lock, W/S: shelf X 2pcs
-
Product
Vehicular Antennas
-
Pulse manufactures a diverse line of outdoor automotive antennas. Our ruggedized, built- to-last antennas cover frequencies 136 MHz to 6 GHz, including GNSS and multi-band antennas. Most antennas are available in a variety of mounting styles including NMO, direct mount, glass, and magnetic mounts, and in many different form factors such as low profile, stealth blade, low profile transit, and whips. Pair your vehicular antenna with our wide variety of high performance, high frequency NMO Mounts making your vehicular installation easier while also insuring the best possible antenna performance. Pulse is a leader in automotive aftermarket antennas and has been a main supplier to large Automotive OEM’s for decades. Find your next automotive antenna and NMO Mount today using the product finder below.
-
Product
DGN Advanced Reporting Feature, GTE 10.00p
K8223B
-
The Basic Diagnostics levels is the main troubleshooting tool used by all users to check the hardware configuration, and verify and isolate hardware failures. Some Diagnostic tests require that a Pin Verification Fixture be installed on the system.
-
Product
Primary Reference Generator
VCH-001
-
The Primary Reference Generator (PEG) VCH-001 is designed to generate the highest accuracy clock signals in a digital communication network. Main areas of application: – synchronization in telecommunication networks.
-
Product
Add Dsc To Your Thermal Analysis Toolkit
-
The analysis of polymers is one of the main applications of differential scanning calorimetry (DSC) solutions. DSC provides complementary data to DEA, but many DSC solutions are prohibitively expensive. Lambient Technologies has partnered with LINSEIS Corp. to offer the industry’s first low-cost DSC/DEA package.
-
Product
Battery Chargers
BAC Series
-
Battery charger BAC series is a portable and universal battery charging solution. It is primarily intended for charging Lead-Acid, Ni-Cd and Li-ion batteries from 1 V DC to 300V DC level. However, the unit can charge the string of any battery type by one of the available charge modes:IU (constant current + constant voltage)UU (constant voltage + constant voltage with a current limit)Charging modes provide a safe regulation of charging procedure and achieves fast recharge and low risk of overcharge.Variety of implemented protections, such as thermal, overcurrent, undervoltage, and overvoltage, assure the charging process will be safe for the battery and the instrument itself.A user doesn’t have to switch off the main charger in order to use BAC series charger. Just the opposite, the BAC series charger should support the main charger to speed up the process. An alternative use is to quickly recharge a battery following a discharge test.The provided display enables users to monitor all relevant information during the charging process and to adjust charging parameters and limits in real-time.The instrument offers the best power-to-weight ratio in the market, weighing only 10 kg / 22 lbs with the maximum output power of 2,7 kW.The maximum charging currents for lead-acid, Ni-Cd and Li-ion batteries, at various battery voltages, are presented in the brochure.
-
Product
Touch (Leakage) Current Meter
LC-2R
-
The test for leakage current in mains operated equipmentis one of the most primary & important tests to verify thequality & electrical safety characteristics of products.
-
Product
HDMI Tester
21-8575-00
-
The HDMI Tester is designed to provide fast convenient verification of proper pin connections of HDMI cables and wall plates. The set includes a Main Test Unit and Remote Test Receiver.
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-1100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of main cable*Ultra big CT window*AC 1mA～30A : 3080turns*AC 30A～3000A : 2000turns
-
Product
HandyScope HS4: 25 MS/s 100MHz BW, 4 Channel, USB Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS4-25
-
The Handyscope HS4 is the successor of the popular Handyscope HS3. Built for customers that want to extend their measuring capabilities even further, this powerful computer controlled measuring instrument now features four input channels. The HS4 has just like it's predecessor the four main measuring instruments: a Multimeter, an Oscilloscope, a Spectrum analyzer and a Transient recorder.
-
Product
DC Power Supply
-
The main products of DC Power Supply are divided into four categories: linear DC power supply, programmable DC power supply, switching DC power supply, and DC power supply, which are subdivided into single output/dual output /Four sets of memory dual output/ high voltage/high power/high resolution/four sets of memory dual output/dual range/customized specifications and other DC power supplies are available for you to choose and use the appropriate DC power supply to get the best results. Best noise performance and device protection.
-
Product
Linemen's Test Set
TeleTalker 330
-
Triplett Test Equipment & Tools
The Triplett TeleTalker™ 330 is a high performance lineman's test set with a weather resistant seal. This butt set offers many standard features not found on more expensive models like dedicated store / redial buttons, adjustable volume, Pulse and Tone dialing, and more. The high impact and weather resistant case allows for this product to be used in all demanding industry settings and features a full 3 year warranty. The user-friendly layout helps installers get the job done effectively with ease. The TeleTalker™ 330 requires no battery for main use and can store up to 10 frequently dialed numbers. Complete with angled bed of nails (JS Popper) test clips.
