Mains Tester
-
product
Energized Tester
ALL-SAFE PRO
Conduct safe, easy and accurate ESA testing in only 60 seconds with the ALL-SAFE PRO® motor connection box. The ALL-SAFE PRO® is a permanently installed connection accessory for the ATPOL III™ energized testing instrument. With this electric motor connection box, the ATPOL III™ can perform tests easily with a quick disconnect.
-
product
Validation Testers
M Series
The M Series line introduces a new class of massively parallel SerDes validation testers that are ideal for high-volume data collection and characterization. Constructed using a collection of Introspect Technology’s D Series modules that are operated seamlessly using the Introspect ESP software, these massively parallel testers are able to interface to high-speed devices in their entirety.
-
product
Socket Tester
1945
Peaceful Thriving Enterprise Co Ltd
This is a portable 220VAC socket tester to inspect the wiring conditions. The tester also features current variation for simulation of different leaking current. With the current variation, technician is able to test the condition of Ground Fault Circuit Interrupter (GFCI) / Residual Current Device (RCD) easily.
-
product
Resistance Tester
KT-2000RD
This equipment represents the wanted resistance value in digital figures and at the same time, is an ohmmeter which decides products to be bad in case of being out of the previously set range of H,L and to be good in case of being within the range. Moreover, because it is designed and manufactured on the basis of KAST's business experiences and know-hows accumulated through on-the-spot works for a long time, it is highly trustable, especially strong to noise and impulse that occur on the bad electric condition of on-the-spot or on the connection with any other equipments, and also is convenient for use.
-
product
Cable Tester
The Cable Test System is a perfect example of a special solution built on existing DapTechnology building blocks. The system, which was developed with the cooperation of a key A&D cable harness supplier, replaces a cable test system with proven FireSpy Technology.
-
product
Compression Tester
Guangzhou Biaoji Packaging Equipment Co., Ltd.
Compression tester is used to test the compression resistance of packaging bag.
-
product
Solar Tester
Amprobe solar meters and analyzers provide you with superior technology to optimize the placement and performance of solar energy equipment. Our meters also offer analysis of window efficiency.
-
product
Hardness Testers
We offer a comprehensive range of hardness testers for Rockwell, Brinell, and Microhardness testing on materials such as metals.
-
product
Roughness Testers
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
-
product
Environmental Testers
Our range of environmental test equipment provide users to test and measure all aspects of the environment. The comprehensive range includes temperature, infra red, sound level, humidity, LUX level and air flow.
-
product
Hipot Testers
We've been manufacturing hipot testers for over 75 years & have supplied many of the worlds leading manufacturers instruments with features that satisfy every type of requirement
-
product
RCD Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
-
product
Headlight Tester
LITE 3
Maschinenbau Haldenwang GmbH & Co. KG.
Quick and accurate testing of the headlight setting Operator-friendly menu guidance using LCD graphic display Measurement recording with CMOS camera technology "Stand alone" version with PC connection Result evaluation with integrated control electronic Easy headlight adjustment with „acoustic setting mode"
-
product
Installation Testers
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
product
Multifunction Tester
EASYTEST
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
product
Trailer Tester
Inspector 930
The Inspector 930 trailer tester is a complete, all-in-one trailer diagnostic system which simplifies ABS, brakes, air, lights, and electrical testing. It provides the ability for a single technician to perform a full inspection in one trip around the trailer.
-
product
LISN Line Impedance Stabilisation Networks / AMN Artificial Mains Network
A LISN Line Impedance Stabilization Networks / AMN Artificial Mains Network: *supplies the neccessary mains voltage (AC or DC) and current for the Equipment under Test (EuT).*couples interference voltage generated by the EuT and supplies it to the receiver.*provides well defined RF-impedance to the Equipment under Test (EuT)*keeps away unwanted disturbance coming from mains (filter)*protects the mains from unwanted disturbance voltage generated by the EuT
-
product
Cable Testers
DMX ADAPTER
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
product
Self-Rectified Generator Power Supply Mains 90 to 300 kV
SITEX C3005
Self-Rectified Generator Power Supply Mains
-
product
Adhesion Testers
Adhesion testing is the best way to determine whether your films and coatings adhere to substrates the way you need them to.
-
product
pH Tester
148
The Elcometer 148 sensor has automatic temperature compensation, ensuring like-for-like measurements can be taken for meaningful comparison of the results.Simultaneously displays pH and temperatureMeasurement hold / freeze functionRecord maximum and minimum readings over a series of tests°C / °F user switchableWaterproof to IP57 and floats on waterAuto power off
-
product
Cable Testers
FiberMASTER
FiberMASTER provides optical loss (dB) measurements meeting Tier 1 certification requirements.
-
product
Mechanical Tester
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
product
Electrical Testers
CURT electrical testers are perfect for testing a new wiring harness on your vehicle or troubleshooting the existing wiring. Our trailer plug testers are built with LEDs and are available in 4-way, 5-way, 6-way and 7-way. We also offer brake control testers.
-
product
Multifunction Testers
1662
The Fluke 1662 installation tester gives you Fluke reliability and all the basic testing power you need for day-in, day-out installation testing. It tests to all local regulations and is easy and intuitive to use. Additional helpful features like the On/Off switchable auto-start for RCD and loop test, and self-test save time and give you more confidence in your results.
-
product
Brinell Hardness Tester
Beijing TIME High Technology Ltd.
Measures a material's resistance to indentation by pressing a hardened steel or carbide ball into its surface with a specific force.
-
product
Beating Pulp Tester
DRK116
Shandong Drick Instruments Co., Ltd.
DRK116 Beating Pulp Tester is applied to test the filter ability of suspending pulp liquid. That is to say the determination of the beating degree. Product features According the inverse proportion relation between beating degree and draining velocity of suspending pulp liquid, designed as Schopper-Riegler beating degree tester.DRK116 Beating Pulp Tester is applied to test filterability of suspending pulp liquid and research fiber condition and evaluate beating degree.
-
product
Ultra-Compact Testers
adaptronic wiring testers of the ultra-compact class are available as low voltage testers and also as high voltage testers, as KT version with display and keyboard and as NT version with the grafical user interface NT Control.
-
product
Pull-Off Adhesion Tester
506
The Elcometer 506 are lightweight, portable and easy-to-use adhesion testers available in analogue or digital gauges and are suitable for measuring the pull-off adhesion of coatings up to 50MPa (7250psi) either on-site, or in the laboratory.
