Programmable Switching Power Supplies
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel, 2.5 Ω to 201 kΩ
40-297A-141
-
The 40-297A-141 (PXI) and the 42-297A-141 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 201 kΩ, 0.25 Ω Resolution. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
USB Power Sensor Module For Measuring Receiver
U5532C
-
The U5532C USB power sensor module is specially design for the N5531X measuring receiver. Based on the Keysight USB power sensor and a power splitter, the U5532C provides the N5531X measuring receiver user with a single RF input device covering up to 50 GHz. Using of the U5532C USB power sensor module eliminates the requirement of an external power meter, simplifying the setup process and saving lab space. The measurement integrity and accuracy are guaranteed by the fully defined specification sets. The traceability of measurement uncertainties is also ensured.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 510 Ohm
40-294-014
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 12-Slot BRIC Matrix, 252x6 1-Pole (3 Sub-cards)
40-558-121-252X6
-
The 40-558-121-252x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
Power, Patchcord, ITA, 36", QuadraPaddle, 16 White Teflon, Single Ended (19 Amps)
7-235916000-036
-
Power, Patchcord, ITA, 36", QuadraPaddle, 16 White Teflon, Single Ended (19 Amps).
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-022
-
The 40-254-022 (PXI) and 42-254-022 (PXIe) are programmable resistor modules with 1 channel which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-350-HI
-
The 40-230-350-HI (PXI) and 42-230-350-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 1.5MΩ with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI-2534, 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-34
-
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2534 is a high-density 8x32 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2534 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
PXI 8-Slot BRIC 168x8 Matrix, 2A 2-Pole (7 sub cards)
40-565A-102-168X8
-
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 239Ω
40-251-113
-
The 40-251-113 is a programmable resistor module with 4 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 8-slot BRIC Matrix, 704x8, 1 pole (11 Sub-cards)
40-558-801-704x8
-
The 40-558-801-704x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 75Ω, MCX
40-837A-102
-
The 40-837A-102 (PXI) and 42-837A-102 are 75Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2Ω to 102kΩ
40-251-134
-
The 40-251-134 is a programmable resistor module with 2 channels which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-250-HI
-
The 40-230-250-HI (PXI) and 42-230-250-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 1.5MΩ with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Mini Power, Contact, Receiver, 65 Amp, 8 AWG
610116112
-
Primary mating contact 610115124. (May mate with other ITA contacts, as well.)Mini Power contacts carry up to 65 amperes continuous current. Maximum resistance is 1 Milliohms.
-
Product
LXI High Density Dual 24x64 2A Matrix
60-552-010
-
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 6.97kΩ
50-298-130
-
The 50-298-130 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 6.97kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Alternate 1.10 (31.18) - 7.20 (204.00) Switch Probe
TSP100-F180-2
-
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
PCI High Density Resistor Card 18-Channel, 8 Bit, 0 To 255 Ohm
50-295A-121-18/8
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Single 2x2 RF Matrix 2.5GHz 50 SMB
40-877-001
-
The 40-877-001 is a 50Ω 2x2 RF matrix with 1 bank in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40-877 modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 1.51MΩ
50-298-144
-
The 50-298-144 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Potentiometer Module 4x12 Bit, 0 Ohm to 4K Ohm
40-296-121-4/12
-
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
Analog Optical Power Meter - MATRIQ
1500 Series
-
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
Product
PXI Expandable 16x16 RF Matrix 50Ohm Lemo 00
45-720A-541
-
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm - SPST
50-294-131
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 8 Slot BRIC 77x16 2-pole (7 sub-cards)
40-562A-122-77X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Precision Resistor Module 9-Channel, 1.5 to 1.81k
40-297-022
-
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Programmable Resistor Module 6x24 Bit, 0 Ohm to 16M Ohm
40-295-121-6/24
-
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
IEC61850-3 20G SFP + 6GE Managed Ethernet Switch, 48DC
EKI-9226G-20FMI
-
-40 ~ 85˚C wide-range operating temperatureDual Power input and 2 relay outputRedundancy: Gigabit X-Ring Pro (ultra high-speed recovery time < 20 ms), RSTP/STP (802.1w/1D),MSTPSecurity: 802.1x (Port-Based, MD5/TLS/TTLS/PEAP Encryption), HTTPS, SSH and SNMPv3Management: SNMP v1/v2c/v3, WEB, Telnet, Standard MIBSFP socket for Easy and Flexible Fiber Expansion20 x Gigabit SFP ports + 6 x Gigabit x RJ-45 ports
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-151
-
The 40-297A-151 (PXI) and the 42-297A-151 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 2.97 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
