Programmable Switching Power Supplies
-
Product
PXI 8 Slot BRIC Matrix, Solid State, 128x8, 1-Pole (4 sub-cards)
40-563B-121-128X8
-
The 40-563B-121-128x8 is an ultra high density 8-slot matrix module with 1-pole switching and is part of our range PXI BRIC matrices. They are available in 2, 4 or 8-slot sizes to suit high performance PXI switching requirements and are constructed using solid state switches.
-
Product
High-Density PXI Multiplexer Switch Modules
-
This range of High-Density Multiplexer Switch Modules provides a compact array of MUX solutions with differing combinations of channel counts and poles. Most of our high-density solutions include isolation relays that allow the MUX to be disconnected from the single input/output port, enabling the convenient interconnection of other channels.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 6.97kΩ
40-251-024
-
The 40-251-024 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 6.97kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
-
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
Standard 5.95 (169.00) - 7.55 (212.00) Switch Probe
MSP-25C
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 50Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 125Full Travel (mm): 3.18Recommended Travel (mil): 85Recommended Travel (mm): 2.16Mechanical Life (no of cyles): 100,000Overall Length (mil): 1,690Overall Length (mm): 42.93Switch Point (mil): 30Switch Point (mm): 0.76
-
Product
PXI 4 Slot BRIC 230x8 1-Pole (5 sub-cards)
40-560A-021-230X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 12-Slot BRIC Matrix, 286x8 2-Pole (13 sub-cards)
40-562B-322-286X8
-
The 40-562B-322-286X8 is a high density BRIC12 matrix module with a size of 286x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm
40-294-022
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 12-Slot BRIC Matrix, 77x16 1-Pole (7 sub-cards)
40-562B-321-77X16
-
The 40-562B-321-77X16 is a high density BRIC12 matrix module with a size of 77x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
LXI High Density 448x4 2-Pole 2A Matrix With BIRST
60-556-027
-
High density double pole matrix capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
LXI High Voltage Matrix 2-pole 200x2
60-310-202
-
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
PXI Precision Resistor Module 4-Channel, 2 to 13.6k
40-297-131
-
These PXI precision resistor modules provide a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
SP4T Microwave Switch Plug-In
1260-164AH/BH
-
The Astronics 1260-164AH/BH is a 2-slot microwave switch plug-in available in two standard configurations with either one or two relays, each being SP4T, 1-pole, 4-throw.
-
Product
PXI 8 Slot BRIC 132x16 1-Pole (12 sub-cards)
40-562A-121-132X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 330x8 1-Pole (11 sub-cards)
40-561A-121-330X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC Module, 2 Resource Distributor, 5 Bus Matrix Inputs
40-569B-125
-
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-125 is a 8 slot module fitted with 5 Bus Matrix Inputs cards and 2 Resource Distributor cards.
-
Product
LXI Low Thermal EMF Matrix 1-pole 56x33
60-510-001
-
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
Product
EN50155 Managed Ethernet Switch
EKI-9512E-4GMX
-
8 x M12 D-Coded 10/100 Mbps ports + 4 x M12 X-Coded 10/100/1000 Mbps ports, Complies with EN50155 & EN50121-3-2, Operating temperature: -40 ~ 75°C, Operating power input range: 16.8~137.5VDC. Supports X-Ring Pro for rapid and predictable convergence, Supports IXM for fast and easy maintenance, Supports N-Key for quick configuration and backup, M12 connector with IP67 rugged housing.
-
Product
PXI 4-Slot BRIC Matrix, 176x4 1-Pole (4 sub-cards)
40-562B-021-176X4
-
The 40-562B-021-176X4 is a high density BRIC4 matrix module with a size of 176x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 2.5Ω to 3.55kΩ
40-298-123
-
The 40-298-123 is a high density programmable resistor module with 4 channels which can be set between 2.5Ω and 3.55kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 395kΩ
40-298-142
-
The 40-298-142 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI BRIC8 FIBO Matrix Dual 62x4 2pin brkout
40-592A-112
-
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
Product
PXI BRIC8 FIBO Matrix Dual 24x2 3pin brkout
40-595A-004
-
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
PXI 8 Slot BRIC Solid State 256x8 1-Pole (8 sub-cards)
40-563A-121-256X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PCI Precision Resistor Card 6-Channel, 3Ω To 2.97MΩ
50-297-051
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI BRIC8 HD FIBO Matrix 186x8 2pin brkout
40-592-121-186X8-2P
-
The 40-592 FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC™ format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short-circuits to ground or battery, or short-circuits between input/output lines.
-
Product
PXI 4 Slot BRIC Matrix, 2A 1-Pole 96x12, 3 Sub-cards
40-597A-003
-
The 40-597A-003 is a PXI 1-pole 96x12 matrix in BRIC4 format and is part of a range of high density matrix modules able to switch up to 2 A or 200 VDC/210 VAC. The 40-597A BRIC modules are available in 2, 4 or 8-slot sizes to suit most high performance PXI matrix requirements, constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI 4-Slot BRIC Matrix, 184x8, 1-Pole (4 sub-cards) Dual Bus
40-560B-021-184X8-M
-
The 40-560B-021-184x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
LXI 64x4, 10A, 1-pole Matrix
60-600-003
-
A high power single pole matrix module capable of switching up to 400VDC/250VAC, 10A (300W/2500VA max power)
-
Product
PXI 8-Slot BRIC Matrix, 264x8 2-Pole (12 sub-cards)
40-562B-122-264X8
-
The 40-562B-122-264X8 is a high density BRIC8 matrix module with a size of 264x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
