-
Product
4-CH Analog Output Module
HSL-AO4-U
Analog Output Module
The HSL-AO4 offers four analog output channels with a high drive capacity based on the HSL bus. The HSL-AO4 also features 16-bit resolution and offset/gain calibration to minimize the power-on 0-voltage drift to meet precise analog output requirements.
-
Product
16 channel 16 bit Digital to Analog Module
CPCI-DA16-2
Digital / Analog Converter
The CPCI-DA16 is a slave Digital to Analog board thatis managed by the host processor on the CPCI bus.The card contains a state machine that performs mostof the work of outputting data, in order to minimize theimpact to the HOST system.
-
Product
PXI-6713, 12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
777795-01
Analog Output Module
12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6713 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6713 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
8-CH 16-Bit PCI Express Analog Output Card
PCIe-6208
Analog Output Module
ADLINK PCIe-6208 series are 8-CH, 16-bit, PCI Express analog output cards which provide high resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 16 Channel
43-765-001
Analog Output Module
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function PXI modules
PXI-2500 Series
Analog Output Module
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
Product
PXI-6722, 13-Bit, 8-Channel, 800 kS/s PXI Analog Output Module
778999-01
Analog Output Module
13-Bit, 8-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6722 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6722 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
96-CH 12-Bit 3 MS/s High-Density Analog Input PCI Express Card
DAQe-2208
Analog Input Module
ADLINK DAQe-2208 is an high-density and high-performance analog input card. The device can sample up to 96 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 48 AI channels in order to achieve maximum noise elimination.
-
Product
sbRIO-9219, Non-Enclosed, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
781027-01
Analog Input Module
Non-Enclosed, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The sbRIO‑9219 is designed for multipurpose testing. With the sbRIO‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel. Non-enclosed modules are designed for OEM applications.
-
Product
Analog Functions
-
Analog Devices designs amplifiers and linear products that deliver high performance and high value. We combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
Product
sbRIO-9218, Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module
783362-02
Analog Input Module
Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.
-
Product
Analog Distribution Amplifier
DA 1:54
-
The DA 1:54 Analog Distribution Amplifier is designed to make it simple to distribute analog signals generated by Spectrum products to multiple locations and to overcome long cable runs. The DA 1:54 consists of three separate amplifier sections that are factory- configured to operate independently or ganged together, depending upon requirements.
-
-
Product
Analog
-
Create complete systems while streamlining your development process and reducing your design risk. We design our mixed-signal, linear, interface and power products for seamless integration with our extensive portfolio of microcontrollers, digital signal controllers, microprocessors and FPGAs.
-
-
Product
Analog Multimeters -VOM
-
Triplett Test Equipment & Tools
Analog Multimeter is a multi-range instrument for electrical and electronic troubleshooting and measurement. It can stand up under rigorous hard usage of the industrial and maintenance environment. Using a unique design and selection of materials, it can withstand the normal accidents of dropping (up to 5 ft.) and rough handling which occur in hard day to day use. Engineered for significant reduction in the need for maintenance by virtual elimination of parts burn out (other than fuses), and parts damage from severe mechanical abuse.
-
Product
Analog Oscilloscope
PS-600
-
*60MHz DUAL TRACE, DUAL TRIGGER.*VERT SENSITIVITY FROM 1mV/DIV TO 15V/DIV.
-
Product
Analog Panel Meters
-
Analog panel meters offer accuracy and dependability and are available in Panel Board, Surface and Window mount styles. We offer variety of AC and DC input panel meters such as ammeters, voltmeters, frequency meters, elapsed time meters, etc.
-
Product
Analog Oscilloscope
PS-251
-
*25MHz, ALT Trigger.*1mV sensitivity.*10ns Resolution.*Component test, Beam-finder*Illuminate, Hold-off, X-Y
-
Product
Analog Cables
-
The SHDB9F-IXBF Cable is a straight pass-through cable that works with compatible switch load and signal conditioning (SLSC) modules.
-
Product
Analog Output PXI Card
GX1642
Analog Output Module
The GX1642 is a 3U PXI digital to analog output board is designed specifically for applications where multiple analog outputs are required. The GX1642 offers precision signal sourcing performance and quality at an economical price.
-
Product
Analog Mixed Signal Testers
-
- PC-performance independent: multiple SPEA CPUs provide test program timing, while pc replacement does not require the test program requalification- Pattern-based programming: -30% test time vs competitors- 64-line synchrobus and 16-line high-speed synchrobus for real-time instrument synchronization: no embedded delay when running pattern-based testing- 99% parallel test efficiency- Multi-site test capabilities for up to 256 devices in parallel- High-density, floating instruments, for true parallel analog test- Universal slot architecture, up to 1,408 channels- RF generators up to 3 GHz
-
Product
Analog Meter
PR-A Series
-
The PR-A Series of series-regulated CV/CC power supplied were designed to provide a compact power supply package with high performance, and ensure excellent reliability as well as excellent design. Four types are available, three 18V types and one 36V type. Whether used individually or connected in series or parallel for greater capacity, the PR-A Series are housed in a compact rack-mount package and can be used on the bench top as well.
-
Product
PXIe-4303 , 24-Bit, 32-Channel, 51.2 kS/s, ±10 V PXI Analog Input Module
783866-01
Analog Input Module
24-Bit, 32-Channel, 51.2 kS/s, ±10 V PXI Analog Input Module—The PXIe‑4303 is a filtered input module for voltage, thermocouple, and current measurements. The module offers you the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
Product
Analog and Digital Interface
425
-
Three quadrature encoder channels with 16-bit countersFour 12-bit D/A outputsEight 12-bit differential A/D inputs, 50 kHz rateWatchdog timerForty-eight bi-directional digital signals for solid state relay boardsPC/ISA compatible
-
Product
NI-9218, 51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module
783362-01
Analog Input Module
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
-
Product
Analog Receiver / RF Tuners
-
The Bandit™ family of analog receivers or RF tuners provide a series of high-performance, stand-alone RF downconverter modules. These products offer a low noise figure, programmable gain and a high dynamic range and ensure there are no gaps in the RF spectrum coverage.
-
Product
Analog I/O Modules
-
Remote RS-485 I/O modules using Modbus RTU protocol offer complete analog I/O for current, voltage, thermocouple or RTD.
-
Product
Analog Test Solutions
ATX series
-
The ATX series of instruments are designed for applications that require an analog performance that is not achievable with industry standard platforms like PXI(e).
-
Product
Digital-To-Analog Converter
DAC-200
-
Advanced Thermal Solutions, Inc.
The DAC-200 is a digital-to-analog converter designed to convert the output of the ATVS family of instruments to 0-5VDC. The device produces an output whereby the voltage is linearly proportional to both the air velocity and temperature for the ATVS product family, including the ATVS-Nxt, ATVS-2020, eATVS-4, eATVS-8, and iQ-200.
